Birlea corona User manual

Vendor: S000238
Page 1 of 6
ASSEMBLY INSTRUCTIONS
CORONA TV CABINET
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE OR
USE YOUR CORONA TV CABINET
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
ASSEMBLY INSTRUCTIONS:
Please check contents and read instructions carefully before commencing assembly
To avoid damages assemble the item on a soft, clean surface
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn
DO NOT use this item unless all fixings are secured
Always use on a level, even surface
t is recommended that two people handle and assemble the item
CARE & MAINTENANCE: To enjoy your urniture or many years please ollow our recommendations
below:
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations
On unpacking the item you may notice an odour due to the production process. However, this will disappear
after a period of time.
Do not place the item next to a radiator or direct sunlight – this item is manufactured in pine but is susceptible
to temperature change. t is recommended an even room temperature be maintained with no sudden
fluctuations.
Do not place hot or cold items directly onto the surface of the item – always use a placemat or marking will
occur
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water, detergents,
aerosol sprays or any polish. The use of these materials would invalidate any claims.
You may wish to retreat the surface to maintain the original finish – this can be done using block wax (un-
perfumed). Please follow the manufacturer’s instructions carefully
Do not place the item onto wet or damp flooring as staining may occur to the floor
Periodically check all screws & fixings to ensure they are secure
DO NOT push the item as this will damage the base
Keep any sharp objects away from the item
www.birlea.com

Vendor: S000238
Page 2 of 6
Parts List Hardware List
Part Description Qty Part Description Qty
1 Top Panel 1 A Wooden Dowel 12
2 Right Panel 1 B 14 mm Screw 32
3 Left Panel 1 C 30 mm Screw 7
4 Base/Shelf Panel 1 D 35 mm Screw 12
5 Back Panel 1 E Hinge 4
6 Door 2 F Handle 2
7 Front Plinth 1 G 19 mm Bolt 2
8 Top Front Frame 1 H Clip 2
9 Middle Front Frame 1 J
Plug
2
10 Bottom Front Frame 1 K Stud 6
11 Side Plinth 2 L Tack 18
** You will need a small mallet and a screwdriver

Vendor: S000238
Page 3 of 6
Step 1: nsert hardware part A using a small mallet (not provided)
DO NOT use any power tools as this may damage the rame and will invalidate any claim
Step 2: Attach the base/shelf panels (4) to the left panel (3) using hardware part D and a screwdriver (not
provided). nsert the top front frame (8), middle front frame (9) and bottom front frame (10).
DO NOT use any power tools as this may damage the rame and will invalidate any claim
Step 3: Attach the right panel (2) using hardware part D and a screwdriver (not provided)
DO NOT use any power tools as this may damage the rame and will invalidate any claim

Vendor: S000238
Page 4 of 6
Step 4: Attach the top panel (1) using hardware part D and a screwdriver (not provided)
DO NOT use any power tools as this may damage the rame and will invalidate any claim
Step 5: Attach the side plin ths (11) and front plinth (7) using hardware part C and a screwdriver (not
provided)
DO NOT use any power tools as this may damage the rame and will invalidate any claim
Step 6: Attach hardware part E to the doors (6) using hardware part B then attach hardware part F using
hardware part G. You will need to use a screwdriver (not provided)
DO NOT use any power tools as this may damage the rame and will invalidate any claim

Vendor: S000238
Page 5 of 6
Step 7: Secure the doors (6) using hardware part B and a screwdriver (not provided)
DO NOT use any power tools as this may damage the rame and will invalidate any claim
Step 8: Attach hardware part H using hardware part B ensuring the small wheels are flush with the edge of the
base. nsert hardware part J ensuring they are level, then push the door against the hardware parts to make 2
small marks on the door. Secure hardware part J using hardware part B. You will need to use a screwdriver
(not provided)
DO NOT use any power tools as this may damage the rame and will invalidate any claim