Birlea COTSWOLD User manual

Vendor: S000159
Page 1 of 10
ASSEMBLY INSTRUCTIONS
COTSWOLD SLEEP STATION - BED
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR COTSWOLD
SLEEP STATION.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
HEALTH & SAFETY:
DO NOT jump on this bed frame.
DO NOT use this bed frame if any parts are missing, damaged or worn.
DO NOT use this bed frame unless all fixings are secured.
Please keep small parts out of reach of children.
lways use on a level, even surface.
WARNING: If this b d is plac d on a non-carp t d floor you must plac som prot ction und r all l gs to stop
th b d fram from moving. If this is not adh r d to th r is no guarant if th b d fram collaps s.
WARNING: High b ds ar not suitabl for childr n und r th ag of six du to th risk of injury from falls.
WARNING: High b ds can pr s nt a s rious risk of injury from strangulation if not us d corr ctly. N v r attach
or hang it ms to any part of th b d that ar not d sign d to b us d with th b ds .g. rop , string, cords,
hooks, b lts, bags tc.
WARNING: Childr n can b com trapp d b tw n th b d and wall, roof pitch, c iling or adjoining pi c of
furnitur . To avoid th risk of s rious injury, th distanc b tw n th top saf ty barri r and adjoining
structur should not xc d 75 mm or shall b mor than 230 mm.
CARE & MAINTENANCE:
ssemble in the room of use.
Periodically check all screws & fixings to ensure they are secure.
DO NOT push the bed frame as this will damage the legs.
lways lift the bed with two people to reposition.
Keep any sharp objects away from the frame.
The maximum mattress height recommended for this frame is 200 mm.
It is necessary to ventilate the room well to keep humidity low and to prevent formation of mold in or
around the frame.
www.birlea.com

Vendor: S000159
Page 2 of 10

Vendor: S000159
Page 3 of 10
Parts List for B d Hardwar List for B d (found in box 1)
Part D scription Box Qty Part D scription Qty
1 Left Headboard 1 1 A 10 x 50 mm Wooden Dowel 25
2 Right Headboard 1 1 B 10 x 40 mm Wooden Dowel 9
3 Plinth 2 2 C llen Key 2
4 Back Siderail 2 1 D 7 x 90 mm Bolt cab.13 6
5 Back Centre Rail 2 1 E
Elliptical Nut
4
6 Back Top Rail 2 1 F ¼” x 80 mm Bolt 4
7 Front Siderail 2 1 G 4 x 30 mm Screw 4
8 Front Centre Rail 2 1 H 4.5 x 50 mm Screw 4
9 Runner 2 2 I 4 x 35 mm Screw 32
10 Support 2 1 J
Spacer Block
2
11 Front Top Rail 2 1 K
Plastic Cap
18
12 Flat Slat 2 1 L 7 x 60 mm Bolt 10
13 Runner Slat 2 2 M
7 x 80 mm Bolt
6
14 Slat 2 11 **You will n d a small mall t and scr wdriv r (not
provid d).
15 Step 2 3
16 Left Ladder Rail 2 1
17 Right Ladder Rail 2 1

Vendor: S000159
Page 4 of 10
St p 1: Insert hardware parts and B using a small mallet (not provided).
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.
St p 2: ttach the plinth (3) to the left headboard (1) and right headboard (2) using hardware parts , C and
D.
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.

Vendor: S000159
Page 5 of 10
St p 3: ttach the side rails to the end panels using hardware parts C, E, F and M.
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.
St p 4: ttach the left ladder rail (16) and right ladder rail (17) to the steps (15) using hardware parts C and
L.
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.

Vendor: S000159
Page 6 of 10
St p 5: Insert hardware part B to the ends of the front centre rail (8) and front top rail (11) using a small
mallet not provided).
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.
St p 6: ttach the assembled ladder using hardware parts L and C.
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.

Vendor: S000159
Page 7 of 10
St p 7: Secure the ladder in position using hardware parts C and L. ttach the support (10) using hardware
part G and a screwdriver (not provided).
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.
St p 8: ttach the runners (9) to a runner slat (13) and the flat slat (12) using hardware part H and a
screwdriver (not provided).
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.

Vendor: S000159
Page 8 of 10
St p 9: ttach the runner slat (13), flat slat (12) and a slat (14) using hardware parts I and J with a
screwdriver (not provided).
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.

Vendor: S000159
Page 9 of 10
St p 10: ttach the remaining slats (14) and runner slat (13) using hardware parts I and J with a screwdriver
(not provided).
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.

Vendor: S000159
Page 10 of 10
St p 11: ttach hardware part K as shown.
DO NOT us any pow r tools as this may damag th fram and will invalidat any claim.
Additional Information:
• For complete product information, images and dimension diagrams please visit the
website www.birlea.com
• If you have any issues with your item please contact the retailer directly you
purchased it from who will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be
shared in our #birleahome feature on Instagram.
Purchase order number: B00383K