Birlea corona User manual

776mm
850mm
425mm
4 m
4m
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR
USING YOUR .CORONA CORNER TV CABINET
ASSEMBLY INSTRUCTIONS
CORONA CORNER TV CABINET
Vendor: S000238
!
f
You
Tube
www.birlea.com
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Page 1 of 8
CARE & MAINTENANCE:
Assemble in the room of use.
To avoid damages assemble the item on a soft, clean surface
Periodically check all screws & fixings to ensure they are secure.
DO NOT push the item as this will damage the base.
Always lift the item with two people to reposition.
Keep any sharp objects away from the item.
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to production processes but this will disappear after a
period of time.
DO NOT place the item next to a radiator or direct sunlight – this item is susceptible to temperature change.
It is recommended an even room temperature be maintained with no sudden fluctuations.
DO NOT place hot or cold items directly onto the surface of the item as marking will occur
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as use of these materials would invalidate any claims.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Birlea advise you use the wall straps provided to further enhance the safety of this product.

PARTS LIST
Part Item Qty
HARDWARE LIST
Part Item Qty
1
1
1
2
1
2
1
1
1
1
1
2
3
4
5
6
7
8
9
10
Right Panel
Left Panel
Base/Shelf Panel
Door
Front Plinth
1
Side Plinth
Middle Front Frame
Bottom Front Frame
Wooden dowel
14mm Screw
30mm Screw
35mm Screw
Hinge
Handle
19mm Bolt
Clip
Plug
Tack
Stud
A
D
G
K
B
E
H
C
F
J
18
33
4
14
7
2
2
2
2
6
30
1
2
3
4
4
5
6
6
7
8
9
10
11
12
13
14
14
13
Top Panel
1
2
12
13
2
11
14
Right Back Column
Left Back Column
Large Back Panel
Small Back Panel
40mm Screw 4
Recycle
2m
01 2 345 6 7891 0
mm 1 1 1 2 1 3 1 4 1 5 1 6
Wall Strap 1
Washer
L
M
N
O2
** You will need a small mallet and a screwdriver.
Vendor: S000238
Top Front Frame
Page 2 of 8

Step 2: Attach hardware part F to the doors (6) using hardware part B then attach hardware part G using hardware
part H. You will need a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 1: Insert hardware part A using a small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
4
10 11
23
and
and
2x
A
A
A
A
A
Step 3: Attach the side plinths (14) using hardware part C and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
C
2
3
14
14
C
2x
6
B
F
G
H
Vendor: S000238
F
F
Page 3 of 8

Step 4: Attach the base/shelf panels (4) and top front frame (7) to the left panel (2) and
right panel (3) using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
3
4
7
8
72
4
9
9
D
D
D
D
10
11
11
10
Step 5: Attach the right back column (10) and left back column (11) using hardware part E and a screwdriver
(not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
E
E
E
E
Vendor: S000238
Page 4 of 8

Step 6: Attach the top panel (1) using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
1
D
D
D
D
D
12 13
Step 7: Attach the large back panel (12) and small back panels (13) using hardware part M and a small mallet
(not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
13
M
Vendor: S000238
Page 5 of 8

Step 9: Secure the doors (6) using hardware part B and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 8: Attach the front plinth (5) using hardware part C and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
5
C
C
C
6
6
B
Vendor: S000238
Page 6 of 8

Step 10: Attach hardware part J using hardware part B ensuring the small wheels are flush
with the edge of the base. Insert hardware part K ensuring they are level, then push the door
against the hardware parts to make 2 small marks on the door. Secure hardware part K using
hardware part B. You will need to use a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
J
J
K
K
6
6
L
L
L
L
L
L
Step 11: Insert hardware part L using a small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
6
B
B
a: b:
c: d:
J
K
K
Vendor: S000238
Page 7 of 8

Step 12: Furniture must be fixed to a wall.
Fix wall strap N to top of furniture using washer O and screw B . With help, move furniture into position.
Wall plugs not supplied. The correct type of fixing must be used for your wall, seek professional
advice if in doubt.
Vendor: S000238
Page 8 of 8
Additional Information:
• For complete product information, images and dimension diagrams please visit the
website www.birlea.com
• If you have any issues with your item please contact the retailer directly you
purchased it from who will be able to resolve any issues with Birlea.
• Why don’t you send us photos of your assembled furniture to [email protected] to be
shared in our #birleahome feature on Instagram.
B
wall
N
O
O