BIXOLON SRP-350plusIII SRP-352plusIII User manual

User's Manual
Network Interface
Rev. 1.00 SRP-350plusIII
SRP-352plusIII
http://www.bixolon.com

Rev. 1.00
- 2 -
Network Interface
■Table of Contents
1. Manual Information........................................................................................................3
2. Precautions ....................................................................................................................3
3. Specifications ................................................................................................................4
4. How to Connect..............................................................................................................5
4-1 Initial WLAN Connection (Windows 2000)..................................................................8
4-2 Initial WLAN Connection (Windows XP) .....................................................................8
4-3 Initial WLAN Connection (Windows VISTA, Windows 7, Windows 8).......................13
5. Configuration ...............................................................................................................19
5-1 WLAN Setting: FTP ..................................................................................................21
5-2 WLAN Setting: Telnet...............................................................................................23
6. Ethernet/WLAN Test by using Windows Test Page..................................................24
7. Factory Reset...............................................................................................................30
7-1 Initializing LAN Settings............................................................................................30
7-2 Initializing WLAN Settings.........................................................................................31
8. Troubleshooting...........................................................................................................33

Rev. 1.00
- 3 -
Network Interface
1. Manual Information
This Network manual provides information on the connection of network with the printer.
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and
quality of all our products. In following, product specifications and/or user manual content
may be changed without prior notice.
2. Precautions
2-1 The printer has to be within 100m (Outdoor) from AP (Access point) to connect
WLAN.Although 35m is able to communicate in door, WLAN could be affected by
environment to be shorten.
2-2 The maximum separating distance may be shortened if transmission obstacles, such
as cement walls, are present
2-3 If a device (such as a microwave oven, wireless LAN, etc.) that uses the same
frequency is present, transmission may be interrupted. Separate the printer and
Bluetooth-enabled device from such interrupting devices by a distance of at least 5m.

Rev. 1.00
- 4 -
Network Interface
3. Specifications
CATEGORIES
FEATURE
IMPLEMENTATION
WLAN
Specification
Standard
IEEE802.11b, IEEE802.11g, IEEE802.11n
Frequency
Range
2.412~2.484GHz
Channels
1 ~ 14 channels
Range
Up to 100m free space (Outdoor)
Connection
Modes
Infrastructure and Ad-hoc (IBSS), Wi-Fi Direct
Security
Open Connection
Shared Key(WEP encryption 64 and 128 bit options)
WPA-PSK, WPA2-PSK
WPA1/2 Enterprise
(EAP-TLS, EAP-TTLS, PEAP, LEAP, FAST)
SSL2 / SSL3 / TLS1
Protocol
DHCP Client, HTTP, HTTPS, TELNET, FTP, ARP,
ICMP, SNMP, IPv4, TCP, UDP
LAN
Specification
Interface
10/100 Base-T All in one (Auto detection)
Protocol
DHCP Client, HTTP, ARP, ICMP, IPv4 ,TCP, UDP

Rev. 1.00
- 5 -
Network Interface
4. How to Connect
(1) Connecting WLAN Printer
Connect to the AP (Access Point) configured in Infrastructure mode in order to connect to
the wireless network
Infrastructure mode
In order to configure the network between wireless terminals, connect to the terminal in
Ad-hoc / Wi-Fi Direct Mode.
Ad-hoc / Wi-Fi Direct mode
A P

Rev. 1.00
- 6 -
Network Interface
(2) Checking Network Setting
1) LAN
Function key
.
a. Turn on the printer.
b. Wait 10 or more seconds until the LAN interface boots up.
c. Push the function key.
d. The settings will be printed only one time since the printer is turned on.
2) WLAN
a. Turn on the printer and wait for about 10 seconds until WLAN interface boots up.
The Error/Paper LED will stop blinking when booting is complete.
b. When booting process is complete, open the printer cover and press the FEED button
for five seconds. The internal buzzer will sound five times and printer will be in WLAN
selection mode. Mount the paper properly, close the cover, and check that the
following information is printed.
Function key
Power
FEED

Rev. 1.00
- 7 -
Network Interface
c. When the above message is printed, you can print and check the WLAN information
as shown below by selecting Mode 1. (Mode 1 can be selected by one short-press of
the Feed button followed by one long-press.)
WLAN F/W VERSION : 0.1
SYSTEM NAME : SRP-350plusIII
NETWORK MODE : ADHOC
ENCRYTION : NONE
ESSID : PRINTER_adhoc
DHCP : ENABLED
IPADDRESS : 192.168.1.1
SUBNET MASK : 255.255.255.0
GATEWAY : 192.168.1.2
PORT : 9100
HTTPS : DISABLED
TELNET : DISABLED
FTP : DISABLED
SNMP : DISABLED
WLAN MACADDRESS
C C 7 A 0 0 0 0 1 0 8 7 7
WLAN Mode Selection
Modes
0: Exit
1: WLAN Information Print
2: WLAN Factory Reset
and Reboot Printer.
3 or more: None
Select Modes by Feed button control
as below.
Step 1. Short-press as many times as
The mode number to choose.
Step 2. Long-press over 1 second.
*e.g. To choose Mode 2, press Feed
Button 3 times(short-short-long)

Rev. 1.00
- 8 -
Network Interface
4-1 Initial WLAN Connection (Windows 2000)
Windows 2000 does not support wireless network setting.
When you use Windows 2000, you need to set the utility option as below after installing
utility program related to the wireless LAN driver that you use.
- Network mode: Ad-hoc
- SSID: PRINTER_adhoc
- IP address: 192.168.1.2
- Subnet Mask: 255.255.255.0
- Authentication (Encryption): Open (None)
4-2 Initial WLAN Connection (Windows XP)
When wireless utility program is installed, you have to set the wireless control values
via the program, otherwise you have to terminate the program in order to do proper
setting after following the steps 'Control Panel>>Administrative tools>>
Services>>Wireless Zero Configuration>>Start'.
1) Right click on the icon, and select Properties.
2) Select and right click on the Wireless Network Connection, and then select Properties.

Rev. 1.00
- 9 -
Network Interface
3) Select Internet Protocol (TCP/IP), and then click Properties.
4) Set the IP settings as shown below, and then click OK.

Rev. 1.00
- 10 -
Network Interface
5) Select the Wireless LAN tab, and then select “Use Windows to configure my wireless
network settings.”
Click the [Advanced] button.
6) Select “Computer-to-computer (ad hoc) network only.”