Black Box LB200A User manual

CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S. 24 hours, 7A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax [phone]
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [email protected]
Multi-Rate
Ethernet Extender
DECEMBER 2006
LB200A

MULTI-RATE ETHERNET EXTENDER
2
CE NOTICE
The CE symbol on your Black Box equipment indicates that it is in compliance
with the Electromagnetic Compatibility (EMC) directive and the Low Voltage
Directive (LVD) of the European Union (EU). A Certificate of Compliance is
available by contacting Technical Support.
RADIO AND TV INTERFERENCE
The Multi-Rate Ethernet Extender generates and uses radio frequency energy,
and if not installed and used properly-that is, in strict accordance with the manu-
facturer’s instructions-may cause interference to radio and television reception.
The Multi-Rate Ethernet Extender has been tested and found to comply with the
limits for a Class A computing device in accordance with specifications in Sub-
part B of Part 15 of FCC rules, which are designed to provide reasonable protec-
tion from such interference in a commercial installation. However, there is no
guarantee that interference will not occur in a particular installation. If the Ether-
net Extender does cause interference to radio or television reception, which can
be determined by disconnecting the unit, the user is encouraged to try to correct
the interference by one or more of the following measures: moving the comput-
ing equipment away from the receiver, re-orienting the receiving antenna and/or
plugging the receiving equipment into a different AC outlet (such that the com-
puting equipment and receiver are on different branches).
WARNING
• This device contains no user serviceable parts. The
equipment shall be returned to Black Box for repairs, or
repaired by qualified service personnel.
• The external power adapter should be a listed Limited
Power Source. Ensure that the power cable used meets
all applicable standards for the country in which it is to
be installed, and that it is connected to a wall outlet
which has earth ground. The mains outlet that is uti-
lized to power the device shall be within 10 feet (3
meters) of the device, shall be easily accessible, and
protected by a circuit breaker.
• Do not work on the system or connect or disconnect
cables during periods of lightning activity.

MULTI-RATE ETHERNET EXTENDER
3
TRADEMARKS USED IN THIS MANUAL
All applied-for and registered trademarks are the property of their respective owners.
NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT
Instrucciones De Seguridad
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para ref-
erencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfi-
era su uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra
o superficie similar puede bloquea la ventilación, no se debe colocar en libre-
ros o gabinetes que impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
In accordance with the requirements of council direc-
tive 2002/96/EC on Waste of Electrical and Electronic
Equipment (WEEE), ensure that at end-of-life you sepa-
rate this product from other waste and scrap and deliver
to the WEEE collection system in your country for recy-
cling.

MULTI-RATE ETHERNET EXTENDER
4
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización
del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean
pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo
particular atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomen-
daciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas
de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea
usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derra-
mados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A. El cable de poder o el contacto ha sido dañado; u
B. Objectos han caído o líquido ha sido derramado dentro del aparato; o
C. El aparato ha sido expuesto a la lluvia; o
D. El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E. El aparato ha sido tirado o su cubierta ha sido dañada.

MULTI-RATE ETHERNET EXTENDER
5
CONTENTS
CE Notice .................................................................................................... 2
Radio and TV Interference.......................................................................... 2
Trademarks Used In This Manual............................................................... 3
Normas Oficiales Mexicanas (NOM) Electrical Safety Statement............. 3
1. General Information ....................................................................................7
1.1 Features ...............................................................................................7
1.2 Description ......................................................................................... 7
2. Installation................................................................................................... 9
2.1 Installing the Multi-Rate Ethernet Extender .......................................9
2.2 Connecting the Twisted-Pair Line Interface..................................... 10
2.3 Connecting the 10/100Base-T Ethernet Interface ............................ 11
2.4 Connecting Power ............................................................................ 12
3. Configuration............................................................................................. 13
3.1 Configuring DIP Switch S1 ..............................................................14
3.1.1 Switch S1-1: Ethernet Auto Sense .........................................14
3.1.2 Switches S1-2 Through S1-4: Data Rate............................... 15
4. Operation................................................................................................... 16
4.1 Power Up ..........................................................................................16
4.2 Front Panel LED Status Monitors .................................................... 16
A. Specifications ............................................................................................ 18
A.1 LAN Connection ..............................................................................18
A.2 Transmission Line ............................................................................18
A.3 Multi-Rate Ethernet Extender Line Rate ..........................................18
A.4 Multi-Rate Ethernet Extender Distance ............................................18
A.5 Line Surge Suppressor ......................................................................18
A.6 LED Status Indicators .......................................................................18
A.7 Power Supply ....................................................................................19
A.8 Temperature Range ..........................................................................19
A.9 Humidity ...........................................................................................19
A.10 Dimensions .......................................................................................19
B. Multi-Rate Ethernet Extender Interface Pin Assignment.......................... 20

MULTI-RATE ETHERNET EXTENDER
6
B.1 10/100Base-T Interface ....................................................................20
B.2 Line Interface ....................................................................................20
C. Distance Chart, Based on 24 AWG (0.5 MM) .......................................... 21

MULTI-RATE ETHERNET EXTENDER
7
1. General Information
Thank you for your purchase of this Black Box product. If any questions arise
during installation or use of the unit, contact Black Box Tech Support at (724)
746-5500.
1.1 Features
•
Easy to install standalone Multi-Rate Ethernet Extenders— no configuration
required
• Auto-MDIX Ethernet
•
Auto-sensing full or half-duplex Ethernet
•
Auto-sensing 10/100Base-T
•
Extends network connections up to 6,000 ft (1.83 km) over 2-wire 24-AWG
unconditioned lines
• Switch selectable line rates up to 16.67 Mbps
•
7 symmetric or asymmetric settings via DIP switch
•
Transparent operation
•
LED indicators for Power, Ethernet Link & Activity, Line Link & Quality of
Line (QOL)
•
Surge suppression up to 20 kA (8/20 µ s)
•
Available in rack-mount or standalone configurations
• Made in the USA
1.2 Description
The Multi-Rate Ethernet Extender/L (Local) and Multi-Rate Ethernet Extender/R
(Remote) provide high speed LAN connections between peered Ethernet LANs,
remote PC’s, or any other network enabled 10/100Base-T device.
Operating in pairs, a Multi-Rate Ethernet Extender/L (Local) located at one end
of the LAN extension and a Multi-Rate Ethernet Extender/R (Remote) at the
other end, these units can automatically forward LAN broadcasts, multicasts, and
frames across a 2-wire voice-grade twisted-pair link. The data is passed transpar-

MULTI-RATE ETHERNET EXTENDER
8
ently (unmodified) through the Multi-Rate Ethernet Extenders. The Ethernet
Extenders automatically add and delete MAC addresses, only passing packets
across the link that are meant for the remote peered LAN.
Figure 1. Typical application
The Local and Remote Multi-Rate Ethernet Extenders work together to create a
transparent extension between two peered Ethernet LANs. Figure 1 shows a typi-
cal point-to-point application.

MULTI-RATE ETHERNET EXTENDER
9
2. Installation
Because the LB200A requires no configuration, it can be installed quickly.
Note If asymmetric transmission or line rates other than 12.5 Mbps are
required, refer to section 3., “Configuration” on page 13.
2.1 Installing the Multi-Rate Ethernet Extender
Do the following:
1. Connect the line interface between the units (refer to section 2.2, “Connect-
ing the Twisted-Pair Line Interface” on page 10)
Note See Figure 2 for the standalone unit’s rear panel arrangements.
2. Connect the Ethernet interface (refer to section 2.3, “Connecting the
10/100Base-T Ethernet Interface” on page 11).
3.
Connect the power plug (refer to section 2.4, “Connecting Power” on
page 12).
Figure 2. Multi-Rate Ethernet Extender standalone rear panel
Power
Made in the USA
LB200A
Line
Ethernet
port
Ethernet
Power
Made in the USA
LB201A
LINK twisted-pair
terminal block
interface
Ethernet
port
LINK twisted-pair
RJ-45 interface
LINK twisted-pair
RJ-45 interface
Line
Ethernet

MULTI-RATE ETHERNET EXTENDER
10
2.2 Connecting the Twisted-Pair Line Interface
The Multi-Rate Ethernet Extender supports communication between two peer
Ethernet LAN sites over a distance of up to 6,000 ft (1.83 km) over 24 AWG
(0.5 mm) twisted-pair wire.
Note Actual distance and link performance may vary depending on the envi-
ronment and type/gauge of wire used.
Follow the steps below to connect the Ethernet Extender interfaces.
Note The Ethernet Extender units work in pairs. One of the units must be a L
(Local), and the other unit must be a R (Remote). It does not matter
which end is the L and which is the R. The link is always initiated by the
Remote. As long as the Local is powered on, the Remote can establish a
link by being powered on or by having its power reset.
1. To function properly, the two Ethernet Extenders must be connected
together using twisted-pair, unconditioned, dry, metal wire, between 19
(0.9mm) and 26 AWG (0.4mm). Leased circuits that run through signal
equalization equipment are not acceptable.
2. The Ethernet Extender is equipped with the LINK interface presented on an
RJ-45. This LINK interface is a two-wire interface. Observe the signal/pin
relationships on the LINK interface jack. For a terminal block LINK inter-
face (LB201A), please contact [email protected].
The RJ-45 connector on the Ethernet Extender's twisted pair interface is polarity
insensitive and is wired for a two-wire interface. The signal/pin relationship is
shown in Figure 3.
Figure 3. Line Driver (RJ-45) twisted pair line interface.
1 (no connection)
2 (no connection)
3 (no connection)
4 (2-Wire RING)
5 (2-Wire TIP)
6 (no connection)
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8