Black Box MT910A User manual

Connect to V.35,
RS-530, or 10BASE-T
terminal interface
types.
VT100™ control port
ith full DS0 mapping.
Nx56-/64-kbps
channel selection
ith speeds up to
1.544 Mbps.
Loaded ith
diagnostics.
Available as a card
for the Managed
MicroRACK.
T
1 CSU/DSUs terminate T1/FT1
circuits over a 4-wire RJ-48C
interface. They convert this
interface to .35, RS-530, or
10BASE-T, depending on model.
T1 CSU/DSUs are an excellent
choice for terminating leased
lines, Frame Relay backbones,
and Internet access. They support
Nx56/Nx64 kbps T1 framing as
well as D4/ESF framing options
and AMI/B8ZS/B7ZS line coding,
plus internal, external, and
network clocking.
Data rates, framing, and
coding options are programmed
by DIP switches or through the
consol port from a T100 terminal
or terminal emulator.
A full range of system and
diagnostic features make setup
simple. T1 CSU/DSUs respond to
central-office-initiated D4 loopup
and loopdown codes, ESF line
loop, and payload loop FDL
Terminate T1/FT1 and convert to V.35,
RS-530, or Ethernet.
KeyFeatures
T1CSU/DSUs
messages. They’re compatible
with three .52 (Bit Error Rate)
test patterns and both local and
remote Telco diagnostics.
T1 CSU/DSUs support
framed Nx56/64 kbps rates up to
1.536 Mbps and unstructured
rates to 1.544 Mbps.
The 10BASE-T model is
particularly suited for LAN-to-LAN
connection. MAC forwarding and
PPP/BCP built-in bridging
provides seamless connection
over the T1 link without the need
of routers. PPP/BCP also enables
you to extend a router’s serial
interface for connection to a
remote Ethernet LAN over the
T1 network.
T1 CSU/DSUs are available in
a choice of .35, RS-530, or
10BASE-T interfaces. Choose
from a standalone version or a
rackmount card which fits into our
Managed MicroRACK.
Managed MicroRACK
When space is at a premium,
choose the 16-Port Managed
MicroRACK system. It holds up to
16 cards and fits into only 2U of
rack space.
The MicroRACK accepts one
or two AC or DC power supplies in
any combination. Each power
supply is capable of providing
100% of your rack power
requirements. In the event of
failure, the other supply
immediately takes over and the
MicroRACK notifies you of the
power failure.
The network management
module enables you to configure,
control, and perform diagnostics
using SNMP or HTTP over a
10BASE-T Ethernet connection.
Black Box Corporation • 1000 Park Drive • Lawrence, PA 15055-1018 • Tech Support: 724-746-5500 • www.blackbox.com • e-mail: [email protected]
© 2002. All rights reserved.
Black Box Corporation.
2/14/2002 #25955

T1 CSU/DSUs
Agency Compliance:
FCC: Part 15 class A and Part 68,
3N8USA-35977-DE-N;
UL: E127709
Clocking: Internal, external, or
network
Coding: AMI or B8ZS
Compliance: FCC Part 15, Class A
and Part 68; AT&T®62411,
TR54016; ANSI T1.403
Diagnostics: .52 511 BERT;
.54 local/remote loop: responds
to CO-initiated loop-up and loop-
down codes; ESF line-loop and
payload FDL messages;
Diagnostics patterns: 511, 2047,
QRSS
DS0 Start Position: Any position,
contiguous/ non-contiguous
mapping when configured via
T100 console
DTE Rates: Nx56/64 kbps
Framing Format: D4 or ESF
perating Temperature: 32 to 122°F
(0 to 50°C)
Humidity Tolerance: 5 to 90%,
noncondensing
Speed: Up to 1.544 Mbps
Interface: T1; plus .35, RS-530, or
10BASE-T
Connectors: All: (1) RJ-48C T1,
(1) DB9 console port;
MT910A-35, MT911C-35:
(1) M/34 F;
MT910A-530, MT911C-530:
(1) DB25 F;
MT910A-10BT, MT911C-10BT:
(1) RJ-45
Power: 100–240 AC
ConnecttwoEthernetLANsoverT1
T1 CSU/DSU
(MT910A-10BT)
T1 CSU/DSU
(MT910A-10BT)
T1 10BASE-T
Network
10BASE-T
Network
CAT5 Cable
(E N737A)
Specifications
Ordering Information
IT M COD
T1 CSU/DSUs
Standalone
.35...................................................................MT910A-35
RS-530 ...........................................................MT910A-530
10BASE-T ..................................................MT910A-10BT
Rackmount
.35 ...................................................................MT911C-35
RS-530............................................................MT911C-530
10BASE-T ..................................................MT911C-10BT
You may also need…
16-Port Managed MicroRACK...................................RM260
SNMP/HTTP Card ......................................RM261C-SNMP
Control Module .........................................................RM262C
AC Power Supply (90–260 AC) .............................PS466A
DC Power Supply (-48 DC) .............................PS466A-DC
Size: Standalone units:
1.5"H x 4.2"W x 5.8"D
(3.8 x 10.7 x 14.7 cm);
Rackmount cards:
3"H x 0.8"W x 7.8"D
(7.6 x 2 x 19.8 cm)
Weight:
Standalone units: 0.8 lb (0.4 kg);
Rackmount cards: 0.4 lb. (0.2 kg)
Managed MicroRACK
Connectors:
PS466A: (1) IEC-320, 3-pin alarm;
PS466A-DC: (3) screw terminals,
3-pin alarm
Power: Single or dual load sharing:
PS466A: 90–260 AC, 50 Hz;
PS466A-DC: -48 DC
Size: 3.5"H x 19"W x 7.3"D
(8.9 x 48.3 x 18.5 cm)
Weight: 6.8 lb. (3.1 kg)
CAT5 Cable
(E N737A)