Black Horse Model BEDE BD-5J Owner's manual

Instruction Manual Book
MadeinVietnam.
ITEM CODE: BH139
SPECIFICATION
1Wingspan:1,450mm (57.09 in).
1Length:1,165 mm (45.87in).
1Flyingweight: 3.3 kg(7.26 lbs).
1Wingarea: 33 dm2.
1Wingloading: 100 g/dm2.
1Wingtype: Naca airfoils.
1Geartype:Electric retract gear,
size:(73.5x 44 x28)mm(not included).
CNCSuspensionMetalStruts(included).
Parts listing required (not included)
1Radio:08channels.
1Servo:08 standard high torqueservos,
size (29 x 13 x 30)mm.
1 EDF: 90mm.
1Battery:8S LIPO 29,6V.
1Speedcontrol: 100A
Recommended EDF and Battery set up (not included)
1EDF: 90mm,Minimum thrust 3.7kg. Midi-fan evo/
HET 650-68-1500 WeMoTec.
1Lipocell:8 cells/ 5000mAh 55C.
1ESC:100A Phoenix Castle.

2
BEDE BD-5J Item code: BH139 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your BEDE BD-5J. Use the parts listing below to
identifyallparts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenewpilotonhiswaytosuccessfulR/Cflight.Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
1Thick cyanoacrylate glue.
130 minute epoxy.
15 minute epoxy.
1Hand or electric drill.
1Assorted drill bits.
1Modellingknife.
1Straightedgeruler.
12mm ball driver.
1Phillips head screwdriver.
1220 grit sandpaper.
190° square or builder’s triangle.
1Wire cutters.
1Masking tape & T-pins.
1Thread-lock.
1Paper towels.
Some more parts.
HARDWARE PACK
Landinggear.....
Toavoidscratching your new airplane,donot
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand toprotectthe table.Keep acoupleof
jars or bowls handy to hold the small parts af-
ter you open the bag.
PARTS LISTING.
FUSELAGE ASSEMBLY
1(1) Fuselage.
WING ASSEMBLY
1(1) Right wing half with pre-installed
aileron.
1(1) Left wing half with pre-installed
aileron.
Tail section assembly
1(1) Vertical stabilizer with pre-
installedrudder.
1(1) Horizontal stabilizer with pre-
installedelevatorhalves.
SUGGESTION.
NOTE.
Pleasetrialfitallthe parts.Makesure youhave
the correct parts and that they fit and are
alignedproperly beforegluing! Thiswillassure
proper assembly.BEDE BD-5J ARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
ofmanyharsh chemicals including thefollow-
ing:paintthinner,C/A glueaccelerator,C/Aglue
debonderandacetone.Donot letthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.

3
BEDE BD-5J Item code: BH139 . Instruction Manual
Caution:
this model is not a toy!
Ifyou are abeginnerto this typeof powered model,pleaseask an experiencedmodel flyer forhelp
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
you have to carry out is important and must be done carefully.Themodel will onlybestrong and fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+Do not start the EDF if people are near.

4
BEDE BD-5J Item code: BH139 . Instruction Manual
REPLACEMENT LARGE PARTS
REPLACEMENT SMALL PARTS
6.Cable wire of nose gear.
4.Plastic part of tailfuselage.
G
k
A. Fuselage.
B. Wing panel(B1,B2).
C.Horizontal stabilizer(C1,C2).
C3.Elevator
D. Rudder.
E.Aluminiumtube wingdihedralbrace.
F. Cacbon tube Horizontal stabilizer.
K.Pilot G.Decal sheet
1.Oleo struts retracts.
3.Oleostruts retractnosegear.
5. Plywood of nose gear
2.Antenna
3x10mm
2x8mm

5
BEDE BD-5J Item code: BH139 . Instruction Manual
11) Install the rubber grommets and brass
eyelets onto the aileron servos.
I.AILERON.
1.INSTALLING THE AILERON SERVOS.
Temporary pin to
keep hinge centered.
Cutthe covering
awayfromthe slot.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
12)Using a modelingknife, removethe cov-
ering at possition show below.
Servotray.
Remove
covering
bottom side.
Flap Aileron
bottom side.
Secure.

6
BEDE BD-5J Item code: BH139 . Instruction Manual
o5. Instal servo tray with aileron servo into
the wing as same as picture below.
2x10mm.
thread
Electric
wire.
Secure.
Aileron controlhorn
Aileron
control horn
InstallAileron control horn as same as
picturebelow.
Repeat the procedure for the other wing
half.
INSTALLING THE AILERON CONTROL
13) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
14)Drill 1,6mm pilotholes throughthe block
of wood for each of the four mounting screws
provided with the servo.
A+B Epoxy
PLUS glue

7
BEDE BD-5J Item code: BH139 . Instruction Manual
Repeat the procedure for the other wing
half.
Installing the aileron linkages as pictures
below.
2x10mm.
INSTALLING THE AILERON
LINKAGES.
II. FLAP
1.INSTALLING THE FLAP SERVO
Secure
35mm. Bottom side
Flap.
Installflap controlhornas sameas
picturebelow.
ControlhornFlap.
2.INSTALLING THE FLAP
CONTROL HORN.

8
BEDE BD-5J Item code: BH139 . Instruction Manual
Repeat the procedure for the other wing
half.
A+B Epoxy
PLUS glue
Control horn
of the flap.
Installing the flap linkages as pictures
below.
3.INSTALLING THE FLAP
LINKAGES.
35mm
Bottom side.
PARTSREQUIRED
Electric retract
(notincluded)
3x15mm.
Onlyincludingoleostruts.
INSTALLING ELECTRIC GEAR
RETRACTS.
(Electric
Not Included.)

9
BEDE BD-5J Item code: BH139 . Instruction Manual
3x15mm
Secure.
Drill a hole
2.5mm
Repeat the procedure for the other gear.
4x12mm
Bottom side.
Secure.

10
BEDE BD-5J Item code: BH139 . Instruction Manual
Seepicturesbelow:
(Notincluded)
INSTALLINGELECTRICEDF-90MM.
Plastic part of tail fuselage.
Open
3x 12mm
Secure.