Black Horse Model Sea Fury BH102 User manual

Instruction Manual book
SPECIFICATION


Wingspan : 1,950 mm 76.77 in.


Length : 1,757 mm 69.17 in.


Weight : 6.8 kg 14.96 Lbs.
Parts listing required (not included).


Radio : 06 channels.


Servo : 10 Standard high torque servos


Engine : O.S GT 33cc gas(35cc gas FUJI IMVAC).
MadeinVietnam.
ITEM CODE:BH102.

2
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your SEA FURY. Use the parts listing below to
identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenew pilotonhisway tosuccessfulR/C flight.Theywillalso beable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landinggear.....
Toavoid scratching yournew airplane,do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand toprotect thetable.Keepacoupleof
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrialfitalltheparts. Makesureyouhave
the correct parts and that they fit and are
alignedproperly beforegluing!Thiswillassure
properassembly.SEAFURYARFis handmade
from natural materials, every plane is unique
andminor adjustmentsmayhave tobe made.
However, you should find the fit superior and
assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglue accelerator,C/Aglue
debonderandacetone. Donotletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.

3
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
Caution: this model is not a toy!
Ifyouare abeginner tothis typeofpowered model,please askan experiencedmodelflyer forhelp
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhaveto carryout isimportant andmust bedonecarefully.The model willonly bestrong and fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
REPLACEMENT LARGE PARTS
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the engine if people are near. Do not stand in line with the side of the propeller.
+ Make engine adjustments from behind the propeller only. Do not reach around the spinning
propeller.
A F1
D2
B2
B1
C
D1 E.
A.Cowling.
B.Wing panel(B1&B2).
C. Fuselage.
E. Rudder.
D. Horizontal stabilizer(D1&D2).
G.
F1.Aluminium tube wing .
F2 F2. Aluminium tube
Horizontal stabilizer.
G.Pilot.

4
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
REPLACEMENT SMALL PARTS
10.Valveoneway.
9.Valve control.
3.Wheels.
7.Air line sets.
8.3 way connector.
16. Plastic for tail gear.
5.Air tank.
15.
13.Plastic parts for pushrod.
1.Air retract main gear.
6.Spinner.
14. Fuel tank.
2.Door mounting wheel.
11. Connector.
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
Flap Aileron
bottomside.
12. springs.
17.Tailgearset.
5x40mm.
4.Mount wood of Air tank.
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
Bottom side

5
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
Aileron
2)Using amodeling knife,remove thecov-
ering at possition show below.
Removecovering
Servo tray.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4)Drill 1,6mmpilot holesthroughtheblock
of wood for each of the four mounting screws
provided with the servo.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
Thread
Electric wire
2x10mm.
Secure.
Secure
Servotray.

6
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
Repeat the procedure for the other wing
half.
Controlhorn of Aileron
2.INSTALLING THE AILERON
CONTROL HORN.
A+B EPOXY
PLUS glue
Control horn
of the aileron
Installing the aileron linkages as pictures
below.
3.INSTALLING THE AILERON
LINKAGES.
3x10mm.
70mm
M3
3x10mm
II. FLAP.
1.INSTALLING THE FLAP SERVOS.
Secure.
Flap

7
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
trayservo
2x10mm.
Electric
wire
Thread
Secure.
2.INSTALLING THE FLAP
CONTROL HORN.
ControlhornofFlap.
Control horn
of the flap
3.INSTALLING THE FLAP
LINKAGES .
3x10mm.
70mm.
A+B EPOXY
PLUS glue

8
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
Repeat the procedure for the other wing
half.
Secure.
INSTALLING AIR RETRACTABLE
LANDING GEAR.
Bottom side.
Aileron.
Flap.
Bottom side.
Aileron.
Flap.
5x40mm
3x15mm
4x12mm

9
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
Secure.
3x15mm

10
SEA FURY - Item code:BH102 INSTRUCTION MANUAL.
Secure
5x40mm