Black Horse Model BH144 Sky Jet Owner's manual

SPECIFICATION
Instruction Manual book


Wingspan : 1,400 mm 55.12 in.


Length : 1,350 mm 53.15 in.


Weight : 4 kg 8.8 Lbs.
Empty Weight: 1.9 kg 4.18 lbs


Radio : 08 channels.


Servo : 08 size (29x13x30)mm.


EDF : 90mm MIDI -FAN EVO/HET 650 - 68 - 1500


Battery : 8S LIPO 29,6V 5,000mAh.


Speed control: Phoenix ICE2 HV120A.
Electric gear retracts and nose gear retract 10Lb(5kg).
Not including electric gears (only including oleo struts). MadeinVietnam.
Item code:BH144

2
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manualthoroughlybeforestartingassemblyofyour SKYJET.Usethepartslistingbelowtoidentify
all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesigned tohelpthenewpiloton his waytosuccessfulR/Cflight. They willalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
Landinggear.....
Toavoid scratching your newairplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftandto protect thetable.Keep a couple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrial fit alltheparts.Makesure you have
the correct parts and that they fit and are
alignedproperlybeforegluing!Thiswillassure
proper assembly.SKY JET ARF is hand made
from natural materials, every plane is unique
andminor adjustments may haveto be made.
However, you should find the fit superior and
assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderand acetone.Donotletthese chemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.

3
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
Caution: this model is not a toy!
Ifyou are a beginner to this type ofpowered model, pleaseask an experienced model flyerfor help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhave to carry out isimportant and must be donecarefully.The model will only be strong andfly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Wear safety glasses.
+ The glow plug clip must be securely attached to the glow plug.
+ Do not start the EDF if people are near.
SAFETY PRECAUTION.

4
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
REPLACEMENT LARGE PARTS
REPLACEMENT SMALL PARTS
4.wire cables(nose gear)
3. Ply wood nose gear.
1.Oleo struts retracts
2.Oleo strut retract nose gear.
B. Wing panels. (B1,B2)
A.Fuselage.
C.Plastic bomb top wing. (C1,C2)
D.Horizontal stabilizer.(D1,D2)
G.Decal sheet
F2.Carbon tube horizontal stabilizer.
F1. Carbon tube wing
E.Vertical stabilizer

5
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
4.Drill 1,5mm pilot holes throughthe block
of wood for each of the four mounting screws
provided with the servo. Install servo into ai-
leron servo tray as same as picture below.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
Secure.
Cutthecovering
awayfromtheslot.
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
Bottom side
2.Using amodeling knife, remove the cov-
ering servo tray.
Aileron
Flap
Bottom side
Servo tray.

6
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
Repeat the procedure for the other wing
half.
2x10mm.
Aileroncontrolhorn
Repeat the procedure for the other wing
half.
INSTALLINGTHEAILERON CONTROLHORN.
Secure
A+B Epoxy
PLUS glue
Installing the aileron linkages as pictures
below.
Control horn
theaileron.
M2 lock nut
40 mm
INSTALLING THE AILERON
LINKAGES.
Electric wire
Thread

7
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
Flap controlhorn
2.INSTALLING THE FLAP CONTROL HORN.
Repeat the procedure for the other wing
half.
2x10mm.
II. FLAP SERVO.
1.INSTALLING THE FLAP SERVOS.
Secure.
A+B Epoxy
PLUS glue
Flap control
horn.

8
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
Flap Aileron.
Bottom side.
Repeat the procedure for the other wing
half.
PARTSREQUIRED
Only including oleo struts.
INSTALLING ELECTRIC GEAR
RETRACTS.
3x15mm
(Electric
Not Included.)
Electric retract
(notincluded)
Installing the flap linkages as pictures
below.
3. INSTALLING THE FLAP
LINKAGES.
M2 lock nut
M2 40 mm

9
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
3x15mm
Drill a hole
2.5mm
Secure.
Secure.
4x12mm
Plastic bomb top wing. (C1,C2)
C
C2
C1

10
SKY JET - Item code: BH144 . INSTRUCTION MANUAL
Repeat the procedure for the other gear.
Seepicturesbelow:
(Notincluded)
INSTALLINGELECTRICEDF-90MM.
Bottomside.
C/Aglue
Bottom side.
Top side.
Top side.