Black Horse Model Blade BH 70 Owner's manual

Instruction Manual book



RecommendedR.C:4channelswith

4-5 servos.



Propeller : 13 x 6.



Speed Control: 60A.



ElectricMotor: AXI 2826/10.



Battery:4-5Cells-Li-Poly-14.8-18.5v- 5.000mAh-20c.

SPECIFICATION

MadeinVietnam.



Wingspan : 1,580mm. 62.20 in.



Length : 1,255 mm. 49.41in.



Weight : 2.5kg. 5.50lbs.

PartsListingrequired(not included).



Radio : 4 channels.



Servo : 04 -05 servos.



Glow Engine : 46-55 cu.in. 2 stroke.

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manualthoroughlybeforestarting assemblyof your BLADE.Use theparts listingbelow toidentify

all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthe newpiloton hiswayto successfulR/Cflight. Theywillalsobeable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

COWLING.

Landinggear.....

Toavoid scratching yournewairplane, donot

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftandtoprotectthe table.Keep acouple of

jars or bowls handy to hold the small parts af-

ter you open the bag.

Pleasetrialfitallthe parts.Makesure youhave

the correct parts and that they fit and are

alignedproperly beforegluing! Thiswillassure

proper assembly. BLADE ARF is hand made

from natural materials, every plane is unique

andminoradjustments mayhave tobemade.

However, you should find the fit superior and

assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing:paintthinner,C/Aglue accelerator,C/Aglue

debonderandacetone.Donotletthesechemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevator halves.

SUGGESTION.

NOTE.

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Do not smoke near fuel

+ Store fuel in a cool, dry place, away from

children and pets.

+ Wear safety glasses.

+Theglowplugclipmustbesecurelyattached

to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

thepropeller.

+ Do not start the engine if people are near.

Donotstand inline withthe sideofthe propel-

ler.

+ Make engine adjustments from behind the

propeller only. Do not reach around the spin-

ningpropeller.

SAFETY PRECAUTION.

REPLACEMENT LARGE PARTS

B. Wingpanel(Left&Right).

C. Fuselage.

A.Cowling.

D . Horizontal stabilizer.

F. Aluminium wing dihedral brace.

E. Vertical stabilizer

REPLACEMENT SMALL PARTS

 1. Install the rubber grommets and brass

eyelets onto the aileron servo.

INSTALLING THEAILERON SERVOS.

Bottom side

C/Aglue

Bottom side

Aileron

Bottom side

C/Aglue

B. C.

D. E.

G. Decal sheet.

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

Bottom side

C/Aglue

Bottom side

C/Aglue

Bottom side

3. Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

provided with the servo. Install servo into ai-

leron servo tray as same as picture below.

4. Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

Thread

Electric wire

2.Usinga modeling knife,remove the cov-

ering servo tray.

5. Instal servo tray with aileron servo into

the wing as same as picture below.

Secure

Bottom side

Remove covering

Servo tray

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

2 x 10 mm.

Secure

Repeat the procedure for the other wing

half.

INSTALLINGTHEAILERONCONTROLHORN.

Nilon control clasp. M3locknut.

3x35mm.

ControlhornofAileron

1. Using a ruler & pen to draw a straight

line as below picture.

2. Locate nylon control horn, nylon con-

trol horn backplates .

Markpoint

Bottom side

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

3. Drillthrough6mm (diameter)the aileron

using the control horn as a guide and screw

the control horn in place.

1. Working with the aileron linkage for

now, thread one clevis onto one of the

threaded wires.

INSTALLING THE AILERON

LINKAGES.

2. Attach the clevis to the outer hole in the

control horn.

3. Plug the aileron servo into the receiver

andcentertheservo.Install theservoarm onto

the servo. The servo arm should be perpen-

dicular to the servo and point toward the mid-

dle of the wing.

M2locknut.

M2clevis.

Snapkeeper.

Bend and

cut after

C/Aglue

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

4. Locate one nylon servo arm, and using

wire cutters,remove all but one of the arms.

Using a 2mm drill bit, enlarge the third hole

out from the center of the arm to accommo-

date the aileron pushrod wire.

5. Using pliers, carefully make a 90 degree

bend down at the mark made. Cut off the ex-

cess wire, leaving about 4mm beyond the

bend.

6.Insert the90degree bend down through

the hole in the servo arm. Install one nylon

snap keeper over the wire to secure it to the

arm.Installtheservoarmretainingscrewand

remove the masking tape from the aileron.

Repeat the procedure for the other wing

half.

JOINING THE WING HALVES.

1. Locate the aluminium wing dihedral

brace.

2. Usingamodeling knife, removethe cov-

ering wing.

3. Test fit the dihedral brace into each wing

half. The brace should slide in easily.

Bottom side

Top side

Bottom side Bottom side

Remove covering

Top side

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

Epoxyglue

INSTALLING THE ENGINE MOUNT.

THERE ARE TWO OPTIONS:

1. ELECTRIC MOTOR

2. ENGINE MOUNT.

1. OPTION 1: ELECTRIC MOTOR.

3 x 15mm 3x 15mm

Maskingtape.

Epoxyglue

C/Aglue

Maskingtape.

Bottom side

Top side

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

2. OPTION 2: ENGINE MOUNT.

Secure

Tie wrap

4 x 25mm

BLADE - ITEM CODE: BH70.INSTRUCTION MANUAL

INSTALLING THE STOPPER ASSEMBLY

FUEL TANK.

1. The stopper has been pre-assembled at

the factory.

2.Usinga modelingknife, cutonelength of

siliconfuelline (thelength of siliconfuel lineis

calculated by how the weighted clunk should

restabout8mmawayfrom therear ofthe tank

andmovefreelyinsidethetank).Connect one

end of the line to the weighted clunk and the

otherendto thenylon pickup tubeinthe stop-

per.

4. Carefully bend the third nylon tube down

ata 45degree angle(usingacigarettelighter).

This tubewill bevent tubetothefuelingvalve.

When the stopper assembly is installed

in the tank, the top of the vent tube should

rest just below the top surface of the tank.

It should not touch the top of the tank.

5. Test fit the stopper assembly into the

tank. It may be necessary to remove some of

the flashing around the tank opening using

amodeling knife. Ifflashing is present, make

sure none of it falls into the tank.

3. Carefully bend the second nylon tube up

ata 45degree angle(usingacigarettelighter).

This tube will be the vent tube to the muffler.

6. When satisfied with the alignment of the

stopper assembly tighten the 3mm x 20mm

machine screw until the rubber stopper ex-

pandsand sealsthe tankopening.Donotover

tighten the assembly as this could cause the

tank to split.

8. Feed three lines through the fuel tank

compartment and through the pre-drilled hole

in the firewall. Pull the lines out from behind

the engine, while guiding the fuel tank into

place. Push the fuel tank as far forward as

possible,the frontof thetank shouldjustabout

touch the back of the firewall.

7. Using a modeling knife, cut 3 lengths of

fuel line 150mm long. Connect 2 lines to the 2

vent tubes and 1 line to the fuel pickup tube in

the stopper.

Blow through one of the lines to ensure

the fuel lines have not become kinked inside

the fuel tank compartment. Air should flow

througheasily.

9. To secure the fuel tank in place, apply a

bead of silicon sealer to the forward area of

thetank, whereit exitsthe fuselagebehind the

enginemountingboxandtotherearofthetank

at the forward bulkhead.

Secure

Vent tube

Fuelfilltube

Fuel pick- up tube

Silicon tube

not included.

Other manuals for Blade BH 70

Table of contents

Other Black Horse Model Toy manuals

Black Horse Model

Black Horse Model Landscape Owner's manual

Black Horse Model

Black Horse Model Westland Lysander Owner's manual

Black Horse Model

Black Horse Model DECATHLON-EP Owner's manual

Black Horse Model

Black Horse Model Cobra Owner's manual

Black Horse Model

Black Horse Model Sea Fury BH102 Owner's manual

Black Horse Model

Black Horse Model MDM-1FOX Owner's manual

Black Horse Model

Black Horse Model BH172 Owner's manual

Black Horse Model

Black Horse Model P-40C Owner's manual

Black Horse Model

Black Horse Model Twister Owner's manual

Black Horse Model

Black Horse Model LF-107 Lunak Owner's manual

Black Horse Model

Black Horse Model FAIRCHILD 24W Owner's manual

Black Horse Model

Black Horse Model Impulse 100TD User manual

Black Horse Model

Black Horse Model BH167 Owner's manual

Black Horse Model

Black Horse Model P.C-9 BH76 Owner's manual

Black Horse Model

Black Horse Model TURBO BEAVER BH162 Owner's manual

Black Horse Model

Black Horse Model Proctor Owner's manual

Black Horse Model

Black Horse Model B-25J Mitchell Owner's manual

Black Horse Model

Black Horse Model Excel 2000 Owner's manual

Black Horse Model

Black Horse Model JU87-STUKA Owner's manual

Black Horse Model

Black Horse Model Macchi MC-200 BH 104 Owner's manual

Black Horse Model

Black Horse Model Extra 260-EP BH55 Owner's manual

Black Horse Model

Black Horse Model PC-9 Owner's manual

Black Horse Model

Black Horse Model B.A. EAGLE Owner's manual

Black Horse Model

Black Horse Model Spitfire 40 User manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

Multiplex

Multiplex EasyStar II Building instructions

iKarus

iKarus ECO 8 Assembly instruction

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions

REVELL

REVELL Bristol Beaufighter TF.X Assembly manual