Black Horse Model HAWKER TYPHOON MK1B Owner's manual

SPECIFICATION


Wingspan : 2,000 mm 78.74 in.


Length :


Weight : 07 kg 15.40 Lbs.


Radio : 08 channels.


Servo : 09 servos.
Instruction Manual book
MadeinVietnam.
1,600mm 62.99 in.


 Engine : O.S GT 22-33 CC Gas.
ITEM CODE:BH132.

HAWKER TYPHOON MK1B - Item code: BH132 . Instruction Manual
2
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your HAWKER TYPHOON MK1B. Use the parts
listing below to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenew pilotonhiswaytosuccessfulR/C flight.Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landinggear.....
Toavoid scratching yournewairplane,donot
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand toprotectthetable.Keepacoupleof
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrialfitall theparts. Makesureyouhave
the correct parts and that they fit and are
alignedproperly beforegluing!Thiswill assure
proper assembly.HAWKER TYPHOON MK1B
ARF is hand made from natural materials,
every plane is unique and minor adjustments
may have to be made. However, you should
find the fit superior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone.Donotletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.

3
HAWKER TYPHOON MK1B - Item code: BH132 . Instruction Manual
Caution: this model is not a toy!
If you are a beginner to this type of powered
model, please ask an experienced model flyer
for help and support. If you attempt to operate
the model without knowing what you are doing
you could easily injure yourself or somebody
else. Please keep your safety and well-being
in mind at all times.
Important: before you start construction
Even if you have already built a large number
of RC models please read right through these
instructions and check all the kit components
against the parts list. We have taken great
trouble to keep construction as simple as
possible, without making any compromises in
the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the
film covering due to major fluctuations in
weather conditions (temperature, humidity
etc.); in rare cases you may even find a slight
warp in a component. These minor faults are
in the nature of film-covered built-up wooden
structures, and can easily be corrected using
a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area
and rub down with a soft
cloth.
When self-tapping screws have to be
screwed into wood, apply a little white
glue to prevent them shaking loose: just
squirt white glue into the hole and fit the
screw.
+ This is not a toy
+ Be sure that no other flyers are using your
radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from
children and pets.
+ Wear safety glasses.
+Theglow plugclip mustbesecurely attached
to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from
the propeller.
+ Do not start the engine if people are near.
Do not stand in line with the side of the propel-
ler.
+ Make engine adjustments from behind the
propeller only. Do not reach around the spin-
ning propeller.
SAFETY PRECAUTION.
Caution! do not heat the film more than is
absolutely necessary. If the air or the iron is
too hot, the film may melt and holes may be
formed.
This model is highly pre-fabricated and can be
built in a very short time. However, the work
which you have to carry out is important and
must be done carefully. The model will only be
strong and fly well if you complete your tasks
competently - so please work slowly and
accurately.
REPLACEMENT LARGE PARTS
Wing warp: Holdthe paneltwisted gently
in the opposite direction to
thewarp, andapply warmair
to remove the creases from
the covering.
F1. Aluminium tube wing dihedral brace.
B. B.
D.
C.
D.
A.
E.
F1.
F2.
F2. Aluminium tube horizontal stabilizer.
A. Cowling.
B. Wing panel.
C. Fuselage.
D.Horizontal stabilizer.
E.Rudder

HAWKER TYPHOON MK1B - Item code: BH132 . Instruction Manual
4
REPLACEMENT SMALL PARTS
 1. Install the rubber grommets and brass
eyelets onto the aileron servo.
INSTALLING THE AILERON SERVO.
I. SERVO
3. Wheels.
4. Tail gear set.
9.Spinner.
1.Air retract main gear.
11.Valve control.
15.Gun sets
2.Door mounting wheel.
6.AirTank.
14. Fuel Tank.
13.Air line set
7.PlywoodAir tank.
Bottom side.
Top side.
5A. Rockets (Right).
10.Valve oneway.
8. 3 way connector.
12.Plastic parts of elevator and rudder
pushrod.
5B. Rockets (Left.)
A.
B.
15.
1.
2. 2.
4.
5.
9.
12.
3. 3
8.
11. 13.
14.
6.
7.
10. A. B.

5
HAWKER TYPHOON MK1B - Item code: BH132 . Instruction Manual
Secure.
Remove
covering.
2)Using amodeling knife,remove thecov-
ering at possition show below.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4)Drill 1,6mmpilotholesthroughtheblock
of wood for each of the four mounting screws
provided with the servo.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
2x10mm.
Tray servo
Electric wire.