Black Horse Model HAWKER HURRICANE Owner's manual

Instruction Manual Book
MadeinVietnam.
SPECIFICATION
1Wingspan : 2,210 mm 87.01 in.
1Length :1,680 mm 66.14 in.
1Weight : 7.5 kg 16.50 lbs.
Parts listing required(not included):
1Engine : 50-55 cc gas
1Radio : 07 channels.
1Servo : 09 standard high torque servos.
ITEM CODE: BH108.

2
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your HAWKER HURICANE . Use the parts listing
below to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it
is capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C
supplierandjoinyourlocalR/CModelFlyingClub.R/CModelFlyingClubsofferavarietyoftraining
proceduresdesignedtohelpthenewpilotonhiswaytosuccessfulR/Cflight.Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
oThick cyanoacrylate glue.
o30 minute epoxy.
o5 minute epoxy.
oHand or electric drill.
oAssorted drill bits.
oModellingknife.
oStraightedge ruler.
o2mm ball driver.
oPhillips head screwdriver.
o220 grit sandpaper.
o90° square or builder’s triangle.
oWire cutters.
oMasking tape & T-pins.
oThread-lock.
oPaper towels.
Some more parts.
HARDWARE PACK
COWLING.
Landing gear.....
To avoid scratching your new airplane, do
not unwrap the pieces until they are needed
for assembly. Cover your workbench with an
old towel or brown paper, both to protect the
aircraft and to protect the table. Keep a cou-
ple of jars or bowls handy to hold the small
parts after you open the bag.
Please trial fit all the parts. Make sure you
havethecorrectparts and that theyfitand are
alignedproperlybefore gluing!This willassure
proper assembly. HAWKER HURICANE ARFis
handmade fromnaturalmaterials, everyplane
is unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
ofmanyharshchemicals including the follow-
ing:paintthinner, C/Aglueaccelerator,C/Aglue
debonderand acetone.Do notletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
o(1) Fuselage.
WING ASSEMBLY
o(1) Right wing half with pre-installed
aileron.
o(1) Left wing half with pre-installed
aileron.
Tail section assembly
o(1) Vertical stabilizer with pre-
installedrudder.
o(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.

3
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
Caution: this model is not a toy!
If you are a beginner to this type of powered
model,pleaseask anexperiencedmodel flyer
forhelpand support. If youattemptto operate
themodelwithoutknowingwhat youare doing
you could easily injure yourself or somebody
else. Please keep your safety and well-being
in mind at all times.
Important: before you start construction
Even if you have already built a large number
ofRCmodelsplease read rightthroughthese
instructions and check all the kit components
against the parts list. We have taken great
trouble to keep construction as simple as
possible, without making any compromises
in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the
film covering due to major fluctuations in
weather conditions (temperature, humidity
etc.); in rare cases you may even find a slight
warp in a component. These minor faults are
in the nature of film-covered built-up wooden
structures, and can easily be corrected using
a heat gun, as commonly used for modelling.
Creases: Blowwarmairoverthe area
and rub down with a soft
cloth.
When self-tapping screws have to be
screwed into wood, apply a little white
glue to prevent them shaking loose: just
squirt white glue into the hole and fit the
screw.
+ This is not a toy
+ Be sure that no other flyers are using your
radiofrequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from
children and pets.
+ Wear safety glasses.
+The glow plug clip must be securely at-
tached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from
the propeller.
+ Do not start the engine if people are near.
Do not stand in line with the side of the pro-
peller.
+ Make engine adjustments from behind the
propeller only. Do not reach around the spin-
ning propeller.
SAFETY PRECAUTION.
Wing warp: Hold the panel twisted
gently in the opposite
direction to the warp, and
apply warm air to remove
the creases from the
covering.
Caution! do not heat the film more than is
absolutely necessary. If the air or the iron is
too hot, the film may melt and holes may be
formed.
This model is highly pre-fabricated and can
bebuilt inaveryshorttime. However,the work
which you have to carry out is important and
must be done carefully. The model will only
be strong and fly well if you complete your
tasks competently - so please work slowly
and accurately.
REPLACEMENT LARGE PARTS
B2
G.
B1
C
D1
F1
A
E
A.Cowling.
K
B. Wing panel (B1&B2).
C. Fuselage.
D. Horizontal stabilizer(D1&D2).
E. Rudder.
F. Aluminium tube wing
dihedral brace.
G. Delcal sheet. K. Pilot.
D2
F. Aluminium tube
Horizontal stabilizer.
F2

4
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
1 1. Install the rubber grommets and brass
eyelets onto the aileron servo.
INSTALLING THE AILERON SERVO.
I. SERVO
12)Usinga modelingknife,remove thecov-
ering at possition show below.
9.Airtank.
10.Tailgearset.
8. Fuel tank.
5.3 way connector.
6. Plastic for tail gear.
4.Radiator 2
3.Radiator 1
15.Antenna
13.Valve one way.
11.Air line sets.
12.Valvecontrol.
Flap Aileron
Bottom side
Servo tray.
Removecovering
REPLACEMENT SMALL PARTS
2. Air retract main gear.
1.Door mounting wheel.
7.Wheels.
14. Spinner.
3
4
56
910
15
14
8
12 13
2. 2. 1
1
7.
11
3x15mm
3x15mm
3x15mm

5
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
13) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
14)Drill1,6mm pilotholesthrough theblock
of wood for each of the four mounting screws
provided with the servo.
o5. Instal servo tray with aileron servo into
the wing as same as picture below.
2.INSTALLING THE AILERON CONTROL HORN.
Aileron controlhorn
Electric wire.
Thread
Secure
Aileron
A+B Epoxy
PLUS glue
2 x 10mm

6
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
Installing the aileron linkages as pictures
below.
Repeat the procedure for the other wing
half.
II. FLAP.
1.INSTALLING THE FLAP SERVOS.
Flap
Thread
Electric wire
2x10mm.
3x10mm
75 mm
Repeat the procedure for the other wing
half.
Aileron
controlhorn.
3.INSTALLING THE AILERON LINKAGES.
Secure

7
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
Installing the aileron linkages as pictures
below.
INSTALLING THE FLAP
LINKAGES.
Repeat the procedure for the other wing
half.
Secure.
2. INSTALLING THE FLAP CONTROLHORN.
Flap control horn.
FlapControl
horn.
3x10mm
75mm
Secure
Repeat the procedure for the other wing
half.
Bottom side.
A+B Epoxy
PLUS glue

8
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
5 x 45mm
Secure
Secure
3 x 15mm
3 x 10 mm
INSTALLING AIR RETRACTABLE
LANDING GEAR.
1. 1.
13.
7. 11. 7.
3x 15mm.
2.
2.
3x 15mm. 12.
5

9
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
Item code: BH108.

10
HAWKER HURRICANE - Item code: BH108 . Instruction Manual
Drillhole
3.5mm
diameter.
Mark point.
Drill hole
3.5mm diameter.
Drillhole
3.5mm diameter.
Drillhole
3.5mmdiameter.
Lock nut
3 x 10 mm
Secure
Secure
Secure