Black Horse Model L-13 Blank User manual

Instruction Manual book
SPECIFICATION


 Wingspan : 2,700mm 106.30 in.


 Length : 1,410 mm 55.51 in.


 Weight : 2.5kg 5.50 Lbs.
Parts listing required(not included).


 Radio : 06 channels.


 Servo : 07 mini servos.


 Electric motor: PULSAR 40


Battery :3S-LIPo-11.1V-3,250mAh


 Speed control : 60A
Made in Vietnam.
ITEM CODE:BH 138

2
L-13 BLANIK Item code: BH138 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your
L-13 BLANIK. Use the parts listing below to
identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
Landing gear.....
To avoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craft and to protect the table. Keep a couple of
jars or bowls handy to hold the small parts af-
ter you open the bag.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installed rudder.
(1) Horizontal stabilizer with pre-
installed elevator halves.
SUGGESTION.
NOTE.
Please trial fit all the parts. Make sure you have
the correct parts and that they fit and are
aligned properly before gluing! This will assure
proper assembly.L-13 BLANIK ARF is hand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing: paint thinner, C/A glue accelerator, C/A glue
debonder and acetone. Do not let these chemi-
cals come in contact with the colors on the
covering and the plastic parts.

3
L-13 BLANIK Item code: BH138 . Instruction Manual
Caution:
this model is not a toy!
If you are a beginner to this type of powered model, please ask an experienced model flyer for help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
you have to carry out is important and must be done carefully. The model will only be strong and fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Wear safety glasses.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the motor if people are near. Do not stand in line with the side of the propeller.
+ Make motor adjustment s from behind the propeller only . Do not reach around the spinning
propeller.

4
L-13 BLANIK Item code: BH138 . Instruction Manual
REPLACEMENT LARGE PARTS
REPLACEMENT SMALL PARTS
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
F1. Carbon tube Horizontal stabilizer.
E. Carbon tube wing dihedral brace.
G. Decal sheet.
K.Pilot
F2. Carbon tube vertical stabilizer.
Temporary pin to
keep hinge centered.
Cut the covering
away from the slot.
2. Plastic parts for pushrod
1.Landing gear.
K
G
A. Fuselage.
B. Wing panel(B1,B2).
C.Horizontal stabilizer(C1,C2).
D. Vertical stabilizer.
Top side
Flap Aileron
Bottom side.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
2.
1.

5
L-13 BLANIK Item code: BH138 . Instruction Manual
2) Using a modeling knife, remove the cov-
ering at possition show below.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4) Drill 1,6mm pilot holes through the block
of wood for each of the four mounting screws
provided with the servo.
Aileron.
Servo tray.
Remove
covering
Secure.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
thread Electric
wire.
Bottom side.
2x10mm.

6
L-13 BLANIK Item code: BH138 . Instruction Manual
Repeat the procedure for the other wing
half.
Installing the aileron linkages as pictures
below.
INSTALLING THE AILERON
LINKAGES.
Aileron control horn
INSTALLINGTHEAILERON CONTROLHORN.
Aileron
control horn
Aileron.
Bottom side
A+B Epoxy
PLUS glue
Secure
Repeat the procedure for the other wing
half.
40 mm.
M2.

7
L-13 BLANIK Item code: BH138 . Instruction Manual
II. FLAP
1.INSTALLING THE FLAP SERVO 2x10mm.
Flap. Bottom side
Secure.
Repeat the procedure for the other wing
half.
thread
Electric
wire.
Install flap control horn as same as pic-
ture below.
Control horn Flap.
2.INSTALLING THE FLAP
CONTROL HORN.
A+B Epoxy
PLUS glue

8
L-13 BLANIK Item code: BH138 . Instruction Manual
Installing the flap linkages as pictures
below.
3.INSTALLING THE FLAP
LINKAGES.
Control horn
of the flap.
35 mm.
M2.
Left bottom side.
Right bottom side.
4x12mm
Secure.

9
L-13 BLANIK Item code: BH138 . Instruction Manual
See pictures below:
INSTALLING ELECTRIC MOTOR.
3x10mm
Secure.
Motor
Rotor shaft
Rotor shaft
Motor
Secure.
4x15mm
Drill a hole 3.8mm
diameter.

10
L-13 BLANIK Item code: BH138 . Instruction Manual
Secure.
Front view
Secure.
2. Mount the servo to the tray using the
mounting screws provided with your radio sys-
tem.
1. Install the rubber grommets and brass
collets into the elevator servo. Test fit the servo
into the servo tray.
ELEVATOR SERVO INSTALLATION.
Elevator
servo
ESC
INSTALLING PROPELLER.
Propeller not included