Black Horse Model P- 47 THUNDERBOLT- EP Owner's manual

MadeinVietnam.
Instruction Manual book


Wingspan : 1,050 mm 41.34 inches.


Length : 950mm 37.4 inches.


Weight : 1 kg 2.2 lbs.
Partslistingrequired(notincluded).


Radio : 04 channels.


Servo : 4 mini servos.
Motor : KMS 2814/05


Battery : 3 Cells-Li-Poly -11.1V - 2.250 mAh.
Speed control : 40A.
Propeller: 9 x 6.
SPECIFICATION
ITEM CODE:BH118.

2
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your P- 47 THUNDERBOLT- EP. Use the parts
listing below to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenew pilotonhiswaytosuccessfulR/C flight.Theywillalso beable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
Landinggear.....
Toavoidscratching yournew airplane,do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand toprotect thetable.Keepacoupleof
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrialfitalltheparts. Makesureyouhave
the correct parts and that they fit and are
alignedproperly beforegluing!Thiswillassure
proper assembly.P-47THUNDERBOLT-EP
ARF is hand made from natural materials,
every plane is unique and minor adjustments
may have to be made. However, you should
find the fit superior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone. Donotletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION.
NOTE.

3
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Caution: this model is not a toy!
Ifyouare abeginner tothistype ofpowered model,pleaseask anexperienced modelflyerfor help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhaveto carryout is importantand mustbedone carefully.The model willonly bestrongand fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ The glow plug clip must be securely attached to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the motor if people are near. Do not stand in line with the side of the propeller.
REPLACEMENT LARGE PARTS
C. Horizontal stabilizer(C1&C2).
F. Aluminium wing dihedral brace.
G. Decal sheet .
D. Rudder.
B. Wing panel. (B1&B2).
A.Fuselage E.Carbontube.
B2.
A.
C1.
C2.
B1.
F.
D.
G.
E.

4
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
6. Wheels.
3. Plastic parts pushrod
5. Plastic strap
2.Aluminium landing gear.
7. Motor mount wood:
I.AILERON
1. INSTALLING THE AILERON
SERVO
1.Door mounting wheel.
REPLACEMENT SMALL PARTS
4. Plastic part bottom fuselage.
1) Install the rubber grommets and brass
eyelets onto the aileron servo.
1.
5.
6.
3.
7.
2.
2x 10mm.
3x 15 mm.
4.
Aileron.
Bottomside of left wing
Aileron.
C/Aglue.
C/Aglue.

5
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
C/Aglue.
C/Aglue.
C/Aglue.
Topside.
C/Aglue.
bottomside.
Servo.
Removecovering
Servo tray.
Servo tray.
Repeat the procedure for the other
wing half.
2. Using amodeling knife, removethe cov-
ering servo tray.

6
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Repeat the procedure for the other wing
half.
4.Drill1,5mm pilotholes through theblock
of wood for each of the four mounting screws
provided with the servo. Install servo into ai-
leron servo tray as same as picture below.
3. Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
Electricwire
Secure.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
2x10mm.
Secure.
Bottom side
2.INSTALLING THE AILERON
CONTROL HORN.
Straightline.
Installaileron controlhorn assame as
picturebelow.
Control horn
aileron.

7
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Control horn of
the aileron.
A+B Epoxy
PLUSGlue.
3.INSTALLING THE AILERON
LINKAGES.
Installing the aileron linkages as pictures
below.
Aileronpushrod.
40 mm.
A+B Epoxy
PLUS glue
Repeat the procedure for the other wing
half.
See pictures below:
1. 1
2.
5. 5.
4
INSTALLING LANDING GEAR.
Bottom side.

8
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
2 x10mm
Secure.
Secure.
A+B Epoxy
PLUS glue

9
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
C/Aglue.
C/Aglue.
Bottom side.
Cut
Plastic
strap
Plastic strap
See pictures below:
Repeat the procedure for the other gear.
3x 15mm
Motor
mount wood:
INSTALLING ELECTRIC MOTOR.

10
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
C/Aglue.
3x 15mm
Epoxyglue.
Secure.
Secure.

11
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
INSTALLING THE ELEVATOR
SERVO.
1. Install the rubber grommets and brass
collets into the elevator servo. Test fit the
servo into the servo tray.
2. Mount the servo to the tray using the
mounting screws provided with your radio
system.
Elevatorservo
Elevatorservo
Front view.
See pictures below:
HORIZONTALSTABILIZER.
100mm
Carbon tube.
6mm

12
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Epoxyglue
Epoxyglue
C/Aglue.
Push
A+B Epoxy
PLUSGlue.

13
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
C/A glue.
Elevator.
hinge
Elevator.
C/A glue.
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
Controlhornofelevator.
ELEVATOR CONTROL HORN
INSTALLATION.
Bottom side.
A+B Epoxy
PLUSGlue.
Elevator
control horn.

14
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
See picture below:
 Elevatorpushrod installas sameas theway
of aileron pushrod.
ELEVATOR PUSHROD INSTALLATION.
Rudder servo
RUDDER INSTALLATION.
C/Aglue
elevator
pushrod.
Rudder servo install as same as method of
elevator servo. See picture below:
Rudder servo
Push
C/Aglue

15
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Topside.
Rudder control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
ControlhornofRudder.
RUDDER CONTROL HORN INSTALLA-
TION.
A+B Epoxy
PLUSGlue.
RUDDER PUSHROD INSTALLATION.
 Rudder pushrod install as same as the way
of aileron pushrod.
Rudder
control horn
Rudder pushrod.
Bottom side.
Rudder pushrod. Elevator
pushrod.

16
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Rudder pushrod.
C/Aglue.
Bottom side.
Top side.
Plastic parts of pushrod.
Cut.
Plasticparts bottomfuselage

17
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
C/Aglue.


1) Plug the servo leads and the switch
leadinto the receiver. You may want to plug
anaileronextensioninto the receiver to make
plugging in the aileron servo lead easier
when you are installing the wing . Plug the
battery pack lead into the switch.


2) Wrap the receiver and battery pack in
the protective foam to protect them from vi-
bration.Use arubberbandormasking tapeto
hold the foam in place.
Tie wrap.
Receiver
Battery
Tie wrap.
Battery
Receiver


3. Position the battery pack and receiver
in place as pictures below.
Do not permanently secure the receiver and
battery until after balancing the model.
Top side.
INSTALLING THE RECEIVERAND BATTERY.


4. Usinga2mm drillbit, drilla holethrough
the side of the fuselage, near the receiver, for
the antenna to exit.

18
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Secure.
Rightwing.
3x10mm
Secure.
Left side
Locatethealuminiumwingdihedralbrace.
*** Test fit the aluminium tube dihedral brace
into each wing haft. The brace should slide in
easily. If not, use 220 grit sand around the
edges and ends of the brace until it fits prop-
erly.
WINGATTACHMENT.
222mm
aluminium 9mm wing dihedral brace.

19
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual
Bottom side.
Bottom side.
Insert and secure


1. It is critical that your airplane be bal-
anced correctly. Improper balance will cause
your plane to lose control and crash.
THE CENTER OF GRAVITY IS LOCATED
63mm BACK FROM THE LEADING EDGE
OF THE WING.


2. Mount the wing to the fuselage. Using a
couple of pieces of masking tape, place them
on the top side of the wing 63mm back from
the leading edge, at the fuselage sides.


3. Turn the airplane upside down. Place
your fingers on the masking tape and care-
fully lift the plane .
BALANCING.
Accurately mark the balance point on the top
of the wing on both sides of the fuselage. The
balance point is located 63mm back from the
leadingedge.This isthebalancepointatwhich
yourmodel shouldbalancefor yourfirstflights.
Later, you may wish to experiment by shifting
the balance up to 10mm forward or back to
change the flying characteristics. Moving the
balance forward may improve the smooth-
ness and arrow- like tracking, but it may then
require more speed for take off and make it
moredifficult toslow downfor landing.Moving
the balance aft makes the model more agile
with a lighter and snappier ”feel”. In any case,
please start at the location we recommend .
 With the wing attached to the fuselage, all
parts of the model installed ( ready to fly), and
empty fuel tanks, hold the model at the
marked balance point with the stabilizer level.
Lift the model. If the tail drops when you
lift,themodel is“tailheavy” andyoumust add
weigh*tothenose.Ifthe nosedrops,itis“nose
heavy” and you must add weight* to the tail to
balance.
*Ifpossible,first attemptto balancethe model
by changing the position of the receiver bat-
tery and receiver. If you are unable to obtain
good balance by doing so, then it will be nec-
essary to add weight to the nose or tail to
achieve the proper balance point.
Ailerons : 10 mm up 10mm down
Elevator : 12 mm up 12 mm down
Rudder : 15mm right 15mm left.


1. Wehighlyrecommendsetting upaplane
using the control throws listed.


2. The control throws should be meas-
ured at the widest point of each control sur-
face.


3. Check to be sure the control surfaces
move in the correct directions.
CONTROL THROWS.
10
10
12
12
Aileroncontrol

20
P-47 THUNDERBOLT-EP- Item code: BH118.Instruction Manual


1. Completely chargeyour transmitterand
receiver batteries before your first day of fly-
ing.


2. Check every bolt and every glue joint in
your plane to ensure that everything is tight
and well bonded.


3. Double check the balance of the
airplane.


4. Check the control surface.


5. Check the receiver antenna . It should
be fully extended and not coiled up inside the
fuselage.


6. Properly balance the propeller.
We wish you many safe and enjoyable
flights with your P-47THUNDERBOLT-EP.
PRE-FLIGHT CHECK.