Black Horse Model sea fury-ep User manual

Instruction Manual book
SPECIFICATION


Wingspan : 1,050mm 41.34 in.


Length : 950 mm 37.4 in.


Weight : 1.05-1.15kg 2.31 - 2.53 Lbs.


Radio : 04 channels.


Servo : 04 mini servos.


Motor : KMS 2814/06


Battery : 3 Cells-Li-Poly-11.1V 2.250mAh


Speedcontrol :40A


Propeller : 10 x 5
MadeinVietnam.
ITEM CODE:BH 126

2
SEA FURY - EP Item code: BH126 . Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your SEA FURY- EP. Use the parts listing below
to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenewpilotonhiswaytosuccessful R/Cflight.Theywill alsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
Landinggear.....
Toavoidscratching yournewairplane,donot
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftandtoprotectthetable.Keepacoupleof
jars or bowls handy to hold the small parts af-
ter you open the bag.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevatorhalves.
SUGGESTION.
NOTE.
Pleasetrialfitalltheparts.Makesure youhave
the correct parts and that they fit and are
alignedproperlybeforegluing!This will assure
properassembly.SEAFURY-EPARFishand
made from natural materials, every plane is
unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone. Donotletthese chemi-
cals come in contact with the colors on the
covering and the plastic parts.

3
SEA FURY - EP Item code: BH126 . Instruction Manual
Caution: this model is not a toy!
Ifyou are a beginner to this type ofpoweredmodel,pleaseaskanexperiencedmodel flyer for help
and support. If you attempt to operate the model without knowing what you are doing you could
easily injure yourself or somebody else. Please keep your safety and well-being in mind at all
times.
Important: before you start construction
Even if you have already built a large number of RC models please read right through these
instructions and check all the kit components against the parts list. We have taken great trouble to
keep construction as simple as possible, without making any compromises in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the film covering due to major fluctuations in weather
conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a
component. These minor faults are in the nature of film-covered built-up wooden structures, and
can easily be corrected using a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area and rub down with a soft cloth.
Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply
warm air to remove the creases from the covering.
Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the
film may melt and holes may be formed.
This model is highly pre-fabricated and can be built in a very short time. However, the work which
youhave to carry out is importantandmustbedonecarefully.Themodelwillonlybestrongand fly
well if you complete your tasks competently - so please work slowly and accurately.
When self-tapping screws have to be screwed into wood, apply a little white glue to prevent
them shaking loose: just squirt white glue into the hole and fit the screw.
SAFETY PRECAUTION.
+ This is not a toy
+ Be sure that no other flyers are using your radio frequency.
+ Wear safety glasses.
+ Keep loose clothing and wires away from the propeller.
+ Do not start the motor if people are near. Do not stand in line with the side of the propeller.
+ Make motor adjustments from behind the propeller only. Do not reach around the spinning
propeller.

4
SEA FURY - EP Item code: BH126 . Instruction Manual
REPLACEMENT LARGE PARTS
1.Landinggear.
3.Door mounting wheel
5.Plastic parts strap.
2. Wheels
6. Plastic parts for pushrod.
4. Plastic parts for bottom fuselage.
7.Spinner
5.
2.
7
3.
6.
4.
1.
B. Wing panel.
A.Fuselage.
C . Horizontal stabilizer.
E. Aluminium wing dihedral brace.
D. Rudder.
REPLACEMENT SMALL PARTS
A.
B. B.
C.
D.
E.
C.
F.
F. Decal sheet.

5
SEA FURY - EP Item code: BH126 . Instruction Manual
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
I. AILERON.
1.INSTALLING THE AILERON SERVOS.
Top side
Aileron
C/Aglue.
C/Aglue.
C/Aglue.
C/Aglue.
Bottom side
Bottom side
Aileron.

6
SEA FURY - EP Item code: BH126 . Instruction Manual
Repeat the procedure for the other wing
half.
2)Usingamodelingknife,removethecov-
ering at possition show below.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
4)Drill1,6mmpilotholesthroughtheblock
of wood for each of the four mounting screws
provided with the servo.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
2x10mm.
Servotray.
Remove
covering
Servotray.
Servotray.
thread
Electric wire.
Secure
Secure.

7
SEA FURY - EP Item code: BH126 . Instruction Manual
INSTALLINGTHEAILERON CONTROLHORN.
Aileroncontrolhorn
A+B Epoxy
PLUS glue
AB
Installing the aileron linkages as pictures
below.
INSTALLING THE AILERON
LINKAGES.
Repeat the procedure for the other wing
half.
40mm
A+B Epoxy
PLUS glue
Aileron
control horn
Bottom side

8
SEA FURY - EP Item code: BH126 . Instruction Manual
PARTSREQUIRED
MAIN GEAR INSTALATION.
Remove
covering
2 x10mm
Markpoint
Secure.
2 x 10mm plastic
strap

9
SEA FURY - EP Item code: BH126 . Instruction Manual
Secure
Plastic
strap
Cut
Plastic
strap
C/Aglue.
C/Aglue.

10
SEA FURY - EP Item code: BH126 . Instruction Manual
Repeat the procedure for the other wing
half.
See pictures below:
Silicon.
Bottom side.
INSTALLING ELECTRIC MOTOR.
INSTALLINGTHE BATTERY.
Tie wrap.
Battery.
Push in to.
Frontview.
3x 15mm
Secure.
Frontview.
See pictures below:

11
SEA FURY - EP Item code: BH126 . Instruction Manual
1. Install the rubber grommets and brass
colletsintothe elevator servo.Test fittheservo
into the servo tray.
2. Mount the servo to the tray using the
mountingscrewsprovidedwithyourradio sys-
tem.
SERVO ELEVATOR AND RUDDER
Installthespinnerbackplate,propellerand
spinner cone. The spinner cone is held in
place using two 3mm x 12mm wood screws.
INSTALLING THE SPINNER.
Secure.
3x 12mm
Servo
elevator
Battery.
Secure.
Servoelevator

12
SEA FURY - EP Item code: BH126 . Instruction Manual
Horizontalstabilizeinstallation .
See picture below.
HORIZONTALSTABILIZER
INSTALLATION.
96mm
Carbon tube.
6mm
Push in to.
Push
Epoxyglue.
75mm

13
SEA FURY - EP Item code: BH126 . Instruction Manual
Epoxyglue.
C/Aglue.
Bottom side.
C/Aglue.
C/Aglue.
C/Aglue.
C/Aglue.
A+ B Epoxy
Plus glue.

14
SEA FURY - EP Item code: BH126 . Instruction Manual
C/Aglue.
C/Aglue.
C/Aglue.
C/Aglue.
Elevator control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
ControlhornofElevator.
ELEVATOR CONTROL HORN INSTALLA-
TION.
Top side.
A+B Epoxy
PLUSglue.
C/Aglue.
Bottomside

15
SEA FURY - EP Item code: BH126 . Instruction Manual
 Elevatorpushrodinstallassameastheway
of aileron pushrod.
ELEVATOR PUSHROD INSTALLATION.
Rudder servo install as same as method of
elevator servo. See picture below:
VERTICAL STABILIZER INSTALLATION.
See picture below.
Elevatorpushrod
Push.
Rudder servo.

16
SEA FURY - EP Item code: BH126 . Instruction Manual
Controlhorn ofRudder.
Rudder control horn install as same as the
way of aileron control horn. Please see pic-
tures below.
RUDDER CONTROL HORN INSTALLA-
TION.
 Rudder pushrod install as same as the way
of aileron pushrod.
RUDDER PUSHROD INSTALLATION.
Top side.
A+B Epoxy
PLUSglue.
Rudder
Controlhorn.
C/Aglue.
Bottom side. Elevatorpushrod
C/Aglue.

17
SEA FURY - EP Item code: BH126 . Instruction Manual
Rudder
pushrod.
Plastic parts of pushrod.
Cut.


1. Plug the servo leads and the switch
leadintothe receiver. You may want to plug
anaileronextensioninto the receiver to make
plugging in the aileron servo lead easier
when you are installing the wing . Plug the
battery pack lead into the switch.


2. Wrap the receiver and battery pack in
the protective foam to protect them from vi-
bration.Usearubberbandormaskingtapeto
hold the foam in place.


3. Position the battery pack and receiver
is as pictures below
C/Aglue
Do not permanently secure the receiver and
battery until after balancing the model.


4)Usinga2mm drill bit, drill a hole through
the side of the fuselage, near the receiver, for
the antenna to exit.
Bottom side.
Elevator
pushrod
Rudder
pushrod.
INSTALLINGTHE RECEIVERANDBATTERY.
Tie wrap.
Receiver

18
SEA FURY - EP Item code: BH126 . Instruction Manual
Right side
Left side
Secure.
*** Test fit the aluminium tube dihedral brace
into each wing haft. The brace should slide in
easily. If not, use 220 grit sand around the
edges and ends of the brace until it fits prop-
erly.
Locate the aluminium wing dihedral brace.
WINGATTACHMENT.
307mm
9mm
3 x 10mm
Aluminiumtube.
Secure.

19
SEA FURY - EP Item code: BH126 . Instruction Manual
Installing the fuselage top hatch as same as
picture below.
C/Aglue
Plastic parts for bottom fuselage.
Bottom side
Bottom side
Topside


1) It is critical that your airplane be bal-
anced correctly. Improper balance will cause
your plane to lose control and crash.
THE CENTER OF GRAVITY IS LOCATED
80MM BACK FROM THE LEADING EDGE
OF THE WING.


2)Mountthewingtothefuselage.Usinga
coupleofpiecesofmaskingtape,placethem
on the top side of the wing 80mm back from
the leading edge, at the fuselage sides.


3. Turn the airplane upside down. Place
your fingers on the masking tape and care-
fully lift the plane .
BALANCING.
Topside
Insert and
secure

20
SEA FURY - EP Item code: BH126 . Instruction Manual


1) We highly recommend setting up a
plane using the control throws listed.


2) The control throws should be meas-
ured at the widest point of each control sur-
face.


3) Check to be sure the control surfaces
move in the correct directions.
CONTROL THROWS.
Ailerons : 10 mm up 10 mm down
Elevator : 12 mm up 12 mm down
Rudder : 15 mm right 15 mm left
Lift the model. If the tail drops when you
lift, the model is “tail heavy” and you must
add weigh* to the nose. If the nose drops, it
is “nose heavy” and you must add weight* to
the tail to balance.
*Ifpossible,firstattemptto balance themodel
by changing the position of the receiver bat-
tery and receiver. If you are unable to obtain
goodbalance by doing so, thenitwillbe nec-
essary to add weight to the nose or tail to
achieve the proper balance point.
 With the wing attached to the fuselage, all
partsofthemodelinstalled(readytofly),and
empty fuel tanks, hold the model at the
markedbalancepointwiththestabilizerlevel.


1) Completely charge your transmitter and
receiver batteries before your first day of fly-
ing.


2) Check every bolt and every glue joint in
your plane to ensure that everything is tight
and well bonded.


3) Double check the balance of the
airplane.


4) Check the control surface.


5) Check the receiver antenna . It should
be fully extended and not coiled up inside the
fuselage.


6) Properly balance the propeller.
We wish you many safe and enjoy-
able flights with your Spitfire - EP.
PRE-FLIGHT CHECK.
Aileron Control
10
10
12
12
Accuratelymarkthebalancepointonthetop
ofthewingonbothsides of the fuselage.The
balance point is located 80mm back from
theleadingedge.Thisisthebalancepointat
whichyourmodel shouldbalanceforyour first
flights. Later, you may wish to experiment by
shifting the balance up to 10mm forward or
back to change the flying characteristics.
Movingthebalanceforwardmayimprove the
smoothness and arrow- like tracking, but it
may then require more speed for take off
and make it more difficult to slow down for
landing. Moving the balance aft makes the
model more agile with a lighter and snappier
”feel”. In any case, please start at the loca-
tion we recommend .