Black Horse Model BEDE BD-5 Owner's manual

Instruction Manual book

SPECIFICATION



Wingspan : 1,450mm 57.09 in.



Length : 1,140 mm 44.88 in.



Weight : 3.3kg 7.26 Lbs.



Radio : 05 channels.



Servo : 07miniservos+3servosRetracts(FUTABAS3170G)



Electricmotor:BL2826/06OUTRUNER



Battery: 4S-LIPO -14.8V - 5.000 mAh



Speed control: 45A



Propeller : 12 x 8

MadeinVietnam.

ITEM CODE:BH 142

BEDE BD-5 Item code: BH142 . Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your BEDE BD-5. Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedto helpthenewpilotonhisway tosuccessfulR/Cflight.Theywillalso beable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

Landinggear.....

Toavoid scratching yournew airplane,do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftand toprotectthetable.Keep acouple of

jars or bowls handy to hold the small parts af-

ter you open the bag.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevatorhalves.

SUGGESTION.

NOTE.

Pleasetrialfit alltheparts. Makesureyouhave

the correct parts and that they fit and are

alignedproperly beforegluing!Thiswillassure

properassembly.BEDEBD-5ARFishandmade

from natural materials, every plane is unique

andminor adjustmentsmayhave tobe made.

However, you should find the fit superior and

assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing:paintthinner,C/Aglueaccelerator,C/Aglue

debonderandacetone. Donotletthese chemi-

cals come in contact with the colors on the

covering and the plastic parts.

BEDE BD-5 Item code: BH142 . Instruction Manual

Caution:

this model is not a toy!

Ifyouare abeginner to thistype ofpoweredmodel, pleaseaskan experiencedmodel flyer forhelp

and support. If you attempt to operate the model without knowing what you are doing you could

easily injure yourself or somebody else. Please keep your safety and well-being in mind at all

times.

Important: before you start construction

Even if you have already built a large number of RC models please read right through these

instructions and check all the kit components against the parts list. We have taken great trouble to

keep construction as simple as possible, without making any compromises in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the film covering due to major fluctuations in weather

conditions (temperature, humidity etc.); in rare cases you may even find a slight warp in a

component. These minor faults are in the nature of film-covered built-up wooden structures, and

can easily be corrected using a heat gun, as commonly used for modelling.

Creases: Blow warm air over the area and rub down with a soft cloth.

Wing warp: Hold the panel twisted gently in the opposite direction to the warp, and apply

warm air to remove the creases from the covering.

Caution! do not heat the film more than is absolutely necessary. If the air or the iron is too hot, the

film may melt and holes may be formed.

This model is highly pre-fabricated and can be built in a very short time. However, the work which

youhaveto carryoutis importantandmust bedone carefully.The modelwill only bestrong and fly

well if you complete your tasks competently - so please work slowly and accurately.

When self-tapping screws have to be screwed into wood, apply a little white glue to prevent

them shaking loose: just squirt white glue into the hole and fit the screw.

SAFETY PRECAUTION.

+ This is not a toy

+ Be sure that no other flyers are using your radio frequency.

+ Wear safety glasses.

+ The glow plug clip must be securely attached to the glow plug.

+ Do not start the EDF if people are near.

BEDE BD-5 Item code: BH142 . Instruction Manual

REPLACEMENT LARGE PARTS

REPLACEMENT SMALL PARTS

D. Rudder. E. Carbon tube wing dihedral brace.

C3.Elevator

B. Wing panel(B1,B2).

A. Fuselage.

C.Horizontal stabilizer(C1,C2). F. Carbon tube Horizontal stabilizer.

K.Pilot

G.Decal sheet

1.Retract main gear.

3.Cable wire of nose gear.

4. Wheels 7.Antenna.

6.Plastic parts for retract servos.

2.Retract nose gear. 5.Plywood of nose gear

H.Cowling

BEDE BD-5 Item code: BH142 . Instruction Manual

Temporary pin to

keep hinge centered.

Cutthecovering

awayfromtheslot.

Assemble then apply drops of thin

C/A to center of hinge,on both sides.

2)Using amodeling knife,remove thecov-

ering at possition show below.

Servotray.

Remove

covering

bottom side.

1) Install the rubber grommets and brass

eyelets onto the aileron servos.

I. AILERON.

1.INSTALLING THE AILERON SERVOS.

Top side

bottom side.

Aileron

Flap

BEDE BD-5 Item code: BH142 . Instruction Manual

5. Instal servo tray with aileron servo into

the wing as same as picture below.

2x10mm.

3) Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

4)Drill 1,6mmpilotholesthroughthe block

of wood for each of the four mounting screws

provided with the servo.

Secure.

thread

Electric

wire.

Secure.

Aileroncontrolhorn

InstallAileron control horn as same as

picturebelow.

A+B Epoxy

PLUS glue

Repeat the procedure for the other wing

half.

INSTALLING THE AILERON CONTROL

BEDE BD-5 Item code: BH142 . Instruction Manual

Repeat the procedure for the other wing

half.

Installing the aileron linkages as pictures

below.

2x10mm.

INSTALLING THE AILERON

LINKAGES.

II. FLAP

1.INSTALLING THE FLAP SERVO

Aileron

control horn

Flap. Bottom side

Secure

Repeat the procedure for the other wing

half.

35mm.

BEDE BD-5 Item code: BH142 . Instruction Manual

Repeat the procedure for the other wing

half.

Installflapcontrol hornas sameas

picturebelow.

ControlhornFlap.

2.INSTALLING THE FLAP

CONTROL HORN.

A+B Epoxy

PLUS glue

Control horn

of the flap.

Installing the flap linkages as pictures

below.

3.INSTALLING THE FLAP

LINKAGES.

35mm

Bottom side.

Topside.

INSTALLING RETRACT SERVOS.

Retract

servos

Topside.

BEDE BD-5 Item code: BH142 . Instruction Manual

PARTSREQUIRED

INSTALLING RETRACTABLE

LANDING GEAR.

5x30mm.

3x15mm.

Retract

servo

Bottom side.

Retract

servo.

Retract

servo.

BEDE BD-5 Item code: BH142 . Instruction Manual

Secure.

5x30mm.

Secure.

3x15mm.

Table of contents

Other Black Horse Model Toy manuals

Black Horse Model

Black Horse Model P47 Thunderbolt Owner's manual

Black Horse Model

Black Horse Model Sedona User manual

Black Horse Model

Black Horse Model Midget Mustang Owner's manual

Black Horse Model

Black Horse Model BH144 Sky Jet Owner's manual

Black Horse Model

Black Horse Model BH180 Owner's manual

Black Horse Model

Black Horse Model EXTRA 300 Owner's manual

Black Horse Model

Black Horse Model CHIPMUNK Owner's manual

Black Horse Model

Black Horse Model Excel 2000 Owner's manual

Black Horse Model

Black Horse Model sea fury-ep Owner's manual

Black Horse Model

Black Horse Model renegade bh66 Owner's manual

Black Horse Model

Black Horse Model Mosquito MK VI User manual

Black Horse Model

Black Horse Model Focke-Wulf FM 190A Owner's manual

Black Horse Model

Black Horse Model Sea Fury BH102 Owner's manual

Black Horse Model

Black Horse Model L-39 Albatros Owner's manual

Black Horse Model

Black Horse Model SPACE WALKER Owner's manual

Black Horse Model

Black Horse Model Piper Cub Owner's manual

Black Horse Model

Black Horse Model Spitfire 40 User manual

Black Horse Model

Black Horse Model MKII Owner's manual

Black Horse Model

Black Horse Model JU87-STUKA Owner's manual

Black Horse Model

Black Horse Model P47 Thunderbolt Owner's manual

Black Horse Model

Black Horse Model P-36A Hawk Owner's manual

Black Horse Model

Black Horse Model P.C-9 BH76 Owner's manual

Black Horse Model

Black Horse Model dornier DO335 User manual

Black Horse Model

Black Horse Model EP-TRAINER Owner's manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

Multiplex

Multiplex EasyStar II Building instructions

iKarus

iKarus ECO 8 Assembly instruction

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions

REVELL

REVELL Bristol Beaufighter TF.X Assembly manual