BLADEZ BF-7.0E User manual

Revised: 1/16/06
ELLIPTICAL BF-7.0E
OWNER’S MANUAL
BLADEZ Corporation
20155 Ellipse
Foothill Ranch, CA 92610
Phone: [phone]
Fax: [phone]
Email: H[email protected]

BF-7.0E
1
INTRODUCTION
Congratulations for selecting the BF-7.0E Elliptical as your primary source of fitness. The
BF-7.0E is designed to make your workouts more effective and enjoyable.
Please read this manual carefully before using the BF-7.0E. This will allow you to get a full
understanding of all the features the Bladez Elliptical provides. If you have questions or
concerns, please contact BLADEZ Corporation or any authorized BLADEZ FITNESS
distributors in your area.
BLADEZ Corporation
20155 Ellipse
Foothill Ranch, CA 92610
Phone: [phone]
Fax: [phone]
Email: H[email protected]
BEFORE YOU BEGIN
It is very important to become familiar with the frequently used components of your
BF-7.0E.

BF-7.0E
2
TABLE OF CONTENTS
SECTION PAGE
1. IMPORTANT SAFETY INSTRUCTIONS........................................................3
2. ASSEMBLY INSTRUCTIONS ....................................................................... 5
3. COMPUTER CONSOLE ..............................................................................23
4. COMPUTER CONSOLE DESCRIPTIONS...................................................24
5. INITIAL SETUP ............................................................................................25
6. WORKOUT OPTIONS..................................................................................26
7. SLEEP MODE..............................................................................................27
8. WARRANTY.................................................................................................28

BF-7.0E
3
SECTION 1
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using the elliptical.
Notice: Before using this or any other exercise equipment consult your family physician
or health care professional to develop a well planned exercise program to fit your health
needs. If you encounter any pain or breathing discomfort while working out, STOP!,and
consult a physician before continuing.
WARNING!
1. Keep children away from machine while in use.
2. Do not wear loose or dangling clothing while using the elliptical.
3. Maximum user weight of this elliptical is 300lbs.
4. Keep a minimum clearance of 18” on each side and 24” at the rear of the elliptical for
safety.
5. The elliptical should never be left unattended when in operation.
6. Close supervision is necessary when this appliance is used by or near children, invalids,
or disabled persons.
7. Use this appliance only for its intended use as described in this manual.
8. Do not use any attachment not recommended by the manufacturer.
9. Call your service center for any service concerns before taking your elliptical in for
repair.
10.Never drop or insert any object into any opening.
11.Do not use outdoors.
12.Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
13.This appliance is intended for household use only.
SAVE THESE INSTRUCTIONS

BF-7.0E
4
IMPORTANT SAFETY INSTRUCTIONS CONTINUED
POWER SUPPLY
Your BF-7.0E Elliptical uses four AA batteries to power the display. Batteries are not
included. We recommend using alkaline batteries. The battery compartment is located
under the small cover on the back of the computer console. If the display begins to dim or
becomes difficult to see, replace the batteries. If you do not plan to use the BF-7.0E for an
extended period, remove the batteries to prevent leakage.
CLEANING
Clean with soap and slightly damp cloth only; never use solvents.

BF-7.0E
5
SECTION 2 - ASSEMBLY INSTRUCTIONS

BF-7.0E
6
ASSEMBLY INSTRUCTIONS CONTINUED

BF-7.0E
7
ASSEMBLY INSTRUCTIONS CONTINUED

BF-7.0E
8
ASSEMBLY INSTRUCTIONS CONTINUED

BF-7.0E
9
ASSEMBLY INSTRUCTIONS CONTINUED

BF-7.0E
10
ASSEMBLY INSTRUCTIONS CONTINUED
For safety, it is recommended that a minimum of two people assemble this elliptical
trainer.
NOTE: Please refer to pages 6-8 to see illustrations of the parts used for each step
of the assembly process. The step numbers printed on the parts blister packs
correspond with the assembly steps in this manual.
STEP 1. Assembly of frame and front lower tube.
1.1Align the bolts in the front lower tube with the holes in the front of the frame. Assemble
the frame and front lower tube with M8 acorn nuts as shown in the illustration above.

BF-7.0E
11
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 2. Assembly of frame and running leg set.
1.1Align the holes in the steel plate of the running legs with the holes at the rear of the
frame and attach using M10 lock washers and M10 bolts as shown.

BF-7.0E
12
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 3. Assembly of center shroud and running leg set.
1.1Align the hole in the center shroud with the hole in the center of the running leg set and
attach with M5 bolt.

BF-7.0E
13
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 4. Assembly of deck set and frame.
1.1 Slide 18.7x26x0.3T wave washer onto the left crankshaft of the frame. Slide the left
deck set steel tube onto the crankshaft on the left side of the frame followed by the
8x25x2.0t flat washer and fasten with M8 bolt.
1.2 Repeat for the right side.
1.3 ATTENTION:
1. During assembly, one person should hold the deck set steel tube while the other
person attaches the tube to the crankshaft.
2. Make sure the deck set and the crankshaft are fastened tightly to avoid any
problems due to the bolt coming loose.

BF-7.0E
14
ASSEMBLY INSTRUCTIONS CONTINUED
NOTE: Before continuing to Step 5, attach the resistance tension cable as shown in the
illustrations below.

BF-7.0E
15
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 5. Assembly of mast and frame.
1.1 First place the mast into the mast boot, then place the mast into the frame steel tube.
Fasten the steel tube with M8 bolts on the side of the steel tube and M8 bolt and curved
washer in the front.
1.2 ATTENTION:
1. During assembly, one person should hold the mast while the other person
connects the mast and the frame and fastens them with the bolts.
2. After fastening the bolts, connect the PCB cable connectors together. Be sure to
align them in the right direction before pressing them together. Slide the mast
boot into position.

BF-7.0E
16
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 6. Assembly of lower handrails, mast and deck set.
1.1 Slide a plastic spacer and a wave washer onto the left horizontal bar. Connect the
upper part of the left handrail with the horizontal bar on the mast. Fasten with M8
washer and bolt.
1.2 Connect the left lower part of the handrail with the bearing at end of the deck set.
Fasten with M12 nut and bolt.
1.3 Repeat for right side.
Caution:
1. The left and right lower handrails are different. Make sure to install them as
shown in the illustration above.
2. During assembly, be careful not to bump into any protruding parts.

BF-7.0E
17
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 7. Assembly of upper handrail to lower handrail.
1.1 Fit the upper left handrail into lower left handrail; fasten it with M8 nuts and bolts.
1.2 Fit the upper right handrail into lower right handrail; fasten it with M8 nuts and bolts.
Caution:
1. The upper left and right handrails are different. Make sure to install them as shown in
the illustration above with the curve outward.

BF-7.0E
18
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 8. Assembly of handrail shrouds.
1.1 Place the front left shroud and the rear left shroud on the horizontal bar and fasten
them with M4 bolts.
1.2 Place the front right shroud and the rear right shroud on the horizontal bar and fasten
them with M4 bolts.

BF-7.0E
19
ASSEMBLY INSTRUCTIONS CONTINUED
STEP 9. Assembly of handrail and deck set plastic covers.
1.1 Place the plastic cover on the front of the left deck set, make sure the bolt hole on the
plastic and the bolt hole on the steel tube are aligned, then fasten the plastic cover
with M4 bolts.
1.2 Place the left and right plastic covers on the handrail set lower end, and fasten with
bolts.
1.3 On the other side of the frame, place the plastic cover on the front of the right deck set,
make sure the bolt hole on the plastic and the bolt hole on the steel tube are aligned,
then fasten the plastic cover with M4 bolts.
1.4 Place the left and right plastic cover on the handrail set lower end, and fasten with M4
bolts.