BLAUBERG Ventilatoren Box-D Series User manual

Box-D
USER'S MANUAL
EN
CEILING FAN

2
www.blaubergventilatoren.de
Box-D
CONTENTS
Safety requirements
Purpose
Delivery set
Designation key
Technical data
Fan design
Mounting and operation guidelines
Connection to power mains
Technical maintenance
Storage regulations
Manufacturer's warranty
Acceptance certificate
Seller information
Connection certificate
Warranty Card
р. 2
р. 3
р. 3
р. 3
р. 4
р. 5
р. 6
р. 9
р. 9
р. 9
р. 12
р. 14
р. 14
р. 14
р. 15
SAFETY REQUIREMENTS
Disconnect the fan from power mains prior to any installation, setup, maintenance and repair
operations.
The fan must be connected by an expert qualified for unassisted operations with electrical
installations up to 1,000 V after being made familiar with the present technical certificate.
Prior to installation check for any visible damage to the impeller, casing and grille.
Also check the casing flow channel for any foreign objects which may damage the impeller
wheel blades. The fan may only be used as intended. No modifications or alterations are allowed.
The fan is not intended for operation by children or any persons with reduced physical, mental
or sensory capacities, lacking practical experience or knowledge unless controlled or briefed
on the device operation by the person responsible for their safety.
The fan may not be used to handle air containing highly flammable substances or vapours
such as alcohol, petrol etc.
The fans take 220-240 V 50/60 Hz single-phase alternating current.
Children being supervised not to play with the appliance!
Disconnect the damper from the power supply (electric mains) prior to any work on the unit.
Power mains connection shall only be performed by a qualified electrician. The nominal electrical
parameters of the fan are given on the manufacturer's label. Any tampering with the internal
connections is prohibited and will void the warranty.
Take the necessary measures to prevent penetration of smoke, carbon monoxide and other
combustion products into the spaces through open smoke ducts or other fire-safety
infrastructure as well as prevent back flow of gases from any appliances which produce gas
flame or naked flame.
The transported air must not contain dust and other solids as well as sticky substances and
fibrous materials.
The unit is not intended for operation in environments with high concentrations of highly
flammable substances or vapours such as alcohol, petrol, insecticides etc.
Do not close or block the inlet and outlet openings of the unit to ensure optimum air flow.
Do not sit on the unit or put any objects on top of it. The unit owner must follow this manual.

PURPOSE
Fan
Fastening kit for wall side mounting
Suspended holding brackets
User's manual
Packing
DELIVERY SET
The fan design is constantly being improved, so some models can slightly differ from those ones
described in this manual.
The Box-D ceiling fan in a metal casing with 100, 125, 150 and 160 mm exhaust outlets (hereinafter
"Fan") is intended for ventilation systems of industrial or residential buildings, swimming
pools, blocks of flats, offices, hospitals, restaurants and other spaces heated during the winter.
The air discharged by the fan must not contain dust, solids, sticky substances and fibrous
materials.
The ambient air temperature must not exceed the limit values given in Table 1.
The fan is designed for installation between the floor slab and the suspended ceiling attached
to the ceiling structure on mounting brackets or to a wall on side mounts (Box-D 100 and
Box-D 125 only).
The fan is designed for extended periods of continuous operation without disconnection
from power mains.
The products meet the requirements of IPX4 hazardous parts access and water ingress
protection standard.
DESIGNATION KEY
Modification:
L- silent-running
Outlet diameter [mm]:
100, 125, 150, 160
Fan designation:
Box-D - ceiling fan
X X X
Box-D 100 L, Box-D 100
Box-D 125 L, Box-D 125
1 item
1 item
2 items
1 item
1 item
1 item
-
4 items
1 item
1 item
Sample designation:
Box-D 125 L - ceiling fan, outlet
diameter - 125 mm, with silent-running motor.
Box-D 150
Box-D 160
www.blaubergventilatoren.de
3
Box-D

4
www.blaubergventilatoren.de
Box-D
TECHNICAL DATA
The names of the fans, their parameters and connecting dimensions are given in tables 1, 2.
H1
L
H1
Table 1
1.1
1.1
1.1
1.1
1.2
Figure 1.1 Figure 1.2
Table 2
Voltage [V]
Frequency [Hz]
Power [W]
Current [A]
3
Maximum air capacity [m /h]
R.P.M.
Sound pressure level at 3 m distance [dB(A)]
o
Max. transported air temperature [ C]
IP rating
Fan type
Dimensions, mm Weight,
kg
Box-D 125 L
Box-D 125
Box-D 100 L
Box-D 100
Box-D 150
Fan type
Pict
1~220-240
50/60
1~220-240
50/60
1~220-240
50/60
1~220-240
50/60
1~220-240
50/60
1~220-240
50/60
1.2
Box-D 160
Box-D 100 L Box-D 100 Box-D 125 L Box-D 125 Box-D 150 Box-D 160

FAN DESIGN
1
2
3
1
4
5
6
7
The Box-D ceiling fan (Fig. 2) comprises of casing 1 with lid 2.
The casing has an exhaust outlet 3 with a check valve
which prevents back flow of air while the fan is off.
Terminal box 4 containing the terminals for
connecting the fan to power mains is mounted
to the casing. Grille 5 with air filter 6 is attached
to the casing with screws.
Decorative front panel 7 locks into the slots on grille 5.
The casing houses a single-phase electric motor
with a centrifugal impeller and backward-curved
blades. The electric motor has integrated thermal
protection and restarts automatically.
The replacement of parts of the safety
suspension system device shall be performed by the
manufacturer, its service agent or suitably qualified
persons!
Figure 2
www.blaubergventilatoren.de
5
Box-D

6
www.blaubergventilatoren.de
Box-D
INSTALLATION AND OPERATION INSTRUCTIONS
The fan is installed between the floor slab and the suspended ceiling by means of
two mounting brackets. The distance between the bracket attachment point and the
suspended ceiling must be within 165 - 390 mm.
The fan installation steps are given in Fig. 5, 6.
The power is supplied via an external terminal box mounted to the fan casing.
WARNING: If unusual oscillating movement is observed, immediately stop using the
ceiling fan and contact the manufacturer, its service agent or suitably qualified persons!
The fan is to be installed so that the blades are more than 2.3 m above the floor!
Figure 4
Figure 3

280 mm
S
1
3
5
7
2
4
6
8
Box-D 100 L, Box-D 100
Box-D 125 L, Box-D 125
Figure 5
www.blaubergventilatoren.de
7
Box-D

8
www.blaubergventilatoren.de
Box-D
S
403,5 mm 250 mm
Box-D 150, Box-D 160
1
3
5
2
4
6
Figure 6

Disconnect the damper from the power supply (electric mains) prior to any work on the unit.
Power mains connection shall only be performed by a qualified electrician. The nominal electrical
parameters of the fan are given on the manufacturer's label. Any tampering with the internal
connections is prohibited and will void the warranty.
The fans take 220-240 V 50/60 Hz single-phase alternating current.
The fan connections (cables and wires) must be durable, insulated and heat-resistant. The external lead-in
(220-240 V 50/60 Hz) must be equipped with a switch built into the stationary wiring to disconnect all the
mains phases. The location of the S external switch must ensure unobstructed access for shutting down
the fan quickly if required.
The conductor cross-section values are given for reference only while the actual selection must be based
on the maximum permissible wire heating which depends on the wire type, its insulation, length and
installation method (i.e. overhead, in pipes or inside the walls).
The recommended current of the switch is the next current in the standard current row following the
maximum current of the connected unit. The switch is not included in the delivery set.
CONNECTION TO POWER MAINS
www.blaubergventilatoren.de
9
Box-D

10
www.blaubergventilatoren.de
Box-D
1
The electrical connections are terminated on the terminal block located inside the fan casing
in accordance with the Wiring Diagram and the terminal designations (Fig. 7).
The terminal designation diagram is given on a label inside the terminal box.
2
3 4
The steps for connecting the fan to power mains are given on Fig. 8.
L
N
X1
1
2
3
N
L
S
~220-240 V
50/60 Hz
4
Figure 7
Figure 8