BLAUBERG Turbo 100 User manual

USER’S MANUAL
Turbo
INLINE MIXED-FLOW FANS
EN

2
EN
CONTENTS
Delivery set................................................................................................................................................................................................................6
Brief description .....................................................................................................................................................................................................6
Operation guidelines ..........................................................................................................................................................................................7
Designation key ....................................................................................................................................................................................................8
Installation .................................................................................................................................................................................................................9
Electronics operation algorithm ..................................................................................................................................................................10
Technical maintenance......................................................................................................................................................................................12
Storage and transportation regulations..................................................................................................................................................12
Manufacturer’s warranty...................................................................................................................................................................................13

3
EN
This user’s manual is a main operating document intended for technical, maintenance, and operating staff.
The manual contains information about purpose, technical details, operating principle, design, and installation
of the Turbo unit and all its modifications.
Technical and maintenance staff must have theoretical and practical training in the field of ventilation systems
and should be able to work in accordance with workplace safety rules as well as construction norms and
standards applicable in the territory of the country.
The information in this user’s manual is correct at the time of the document’s preparation.
The Company reserves the right to modify the technical characteristics, design, or configuration of its products
at any time in order to incorporate the latest technological developments.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means in any information search system or translated into any language in any form without the prior
written permission of the Company.

4
EN
READ THE USER’S MANUAL CAREFULLY BEFORE PROCEEDING WITH INSTALLATION WORKS.
COMPLIANCE WITH THE MANUAL REQUIREMENTS ENSURES RELIABLE OPERATION AND LONG
SERVICE LIFE OF THE UNIT.
KEEP THE USER’S MANUAL AVAILABLE AS LONG AS YOU USE THE UNIT. YOU MAY NEED TO
REREAD THE INFORMATION ON THE PRODUCT SERVICING.
FOLLOW THE USER’S MANUAL REQUIREMENTS TO ENSURE DURABLE AND
TROUBLE-FREE OPERATION OF THE UNIT.
SAFETY INSTRUCTIONS
Disconnect the unit from power supply prior to any connection, servicing,
maintenance, and repair operations.
Only qualied electricians with a work permit for electrical units up
to 1000 V are allowed for installation and maintenance. The present
user’s manual should be carefully read before beginning works.
• Single-phase power mains must comply with the acting local electrical
norms and standards.

5
EN
• Fixed electrical wiring must be equipped with an automatic circuit
breaker.
• The unit must be connected to power mains through a QF automatic
circuit breaker integrated into the fixed wiring system. The gap between
the circuit breaker contacts on all poles must be not less than 3 mm.
Check the unit for any visible damages of the impeller and the casing
before starting installation. The casing internals must be free of any
foreign objects that can damage the impeller blades.
• While mounting the unit, avoid compression of the casing! Deformation
of the casing may result in the motor jam and noisy operation. Misuse of
the unit and any unauthorised modifications are not allowed.
• Take steps to prevent ingress of smoke, carbon monoxide, and other
combustion products into the room through open chimney flues or other
fire-protection devices. Sufficient air supply must be provided for proper
combustion and exhaust of gases through the chimney of fuel burning
equipment to prevent back drafting. Transported air must not contain any
dust or other solid impurities, sticky substances, or fibrous materials.
• Do not use the unit in a hazardous or explosive environment containing
spirits, gasoline, insecticides, etc.

6
EN
THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.
DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC WASTE.
• Do not close or block the intake or extract vents in order to ensure the
efficient air flow.
• Do not sit on the unit and do not put objects on it.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
Ensure that the fan is switched off from the supply mains before removing
the guard.
The fan is to be installed so that the blades are more than 2,1 m above the
floor;
Precautions must be taken to avoid the back-flow of gases into the room
from the open flue of gas or other fuel-burning appliances.

7
EN
DELIVERY SET
Fan — 1 pc.
Screws and dowels — 4 pcs.
Plastic screwdriver (for models with a timer) — 1 pc.
User’s manual — 1 pc.
Packing box — 1 pc.
BRIEF DESCRIPTION
The product described herein is a mixed-flow inline fan for supply or extract ventilation of premises.
The fan is designed for connection to ø 100, 125, 150, 160, 200, 250 and 315 mm air ducts.
The unit is equipped with a two speed motor.
Ø D B H L
Turbo 100 97 195,8 226/255* 302,5
Turbo 125 123 195,6 226/255* 258,5
Turbo 150 148 220,1 247/265* 289
Turbo 160 158 220,1 247/265* 289
Turbo 200 199 239 261/278* 295,5
Turbo 250 247 287 323/340* 383
Turbo 315 310 362 408/424* 445
* Turbo XXX GI1/G1/GTI1/GT1/GSI1/GS1

8
EN
OPERATION GUIDELINES
The fan is rated for connection to single-phase AC 220-240 V/50 Hz or 220 V/60 Hz power mains.
The unit is rated for continuous operation.
The arrow on the fan casing must match the air direction in the system.
Ingress protection rating against access to hazardous parts and water ingress is IPX4.
The unit is rated as a Class II electrical appliance.
The fan is rated for operation at the ambient air temperature from +1 °C up to +40 °C.
Power supply [V/Hz] Transported air temperature [°C]
220-240/50 -25...+60
220/60 -25...+40
IF THE POWER CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, CUSTOMER
SERVICE, OR SIMILAR QUALIFIED PERSONNEL IN ORDER TO AVOID DANGER.

9
EN
DESIGNATION KEY
Turbo XXX X
Options:
T: timer
US: speed switch
Gl1: speed controller with an electronic thermostat and a temperature
sensor integrated inside an air duct. Temperature-based operation logic
G1: speed controller with an electronic thermostat and an outdoor
temperature sensor fixed on a 4 m cable. Temperature-based operation logic
GTl1: speed controller with an electronic thermostat and an integrated
temperature sensor. Timer-based operation logic
GT1: speed controller with an electronic thermostat and an outdoor
temperature sensor fixed on a 4 m cable. Timer-based operation logic
GSl1: speed controller with an electronic thermostat and an integrated
temperature sensor. Temperature-based switching on/off
GS1: speed controller with an electronic thermostat and an outdoor
temperature sensor fixed on a 4 m cable. Temperature-based switching on/
off.
Spigot diameter [mm]
Inline mixed-ow fan

10
EN
MOUNTING
The fan is suitable both for horizontal or vertical mounting on the floor, on the wall or on the ceiling (Fig. 1).
The fan can be installed independently or as part of a set with parallel or in-series connection (Fig. 2).
Install minimum 1 m long air duct on the intake spigot side in case of horizontal fan mounting or a hood in
case of vertical fan mounting.
The outlet spigot must always be connected to the air duct. The fan mounting sequence is shown in Fig. 3-11
and 14-19.
The fan wiring diagrams are shown in Fig. 12-13. Some fan models are equipped with a plastic limit stop in
front of the L1 terminal. Remove the limit stop for connection to the L1 terminal.
Designation:
L1 – minimum speed terminal
L2 – maximum speed terminal
QF – automatic circuit breaker
S– external speed controller
ST – external switch (for example, a light switch)
X – input terminal
QF
SS/ST
Automatic circuit breaker
designation
Automatic
circuit breaker
External switch designation External switch