BlissLights Spright Smart User manual

User’s Guide
Manufactured by: BlissLights
Phone: [phone]
Fax: [phone]
www.BlissLights.com
suppor[email protected]
MADE IN CHINA
Please ONLY use
manufacturer
provided transformer

TABLE OF CONTENT
Notice ..............................................................................................................................1
Before You Begin..........................................................................................................2
Parts List..........................................................................................................................2
Setting up the BlissLights Spright Smart............................................................3
Installation Tips ............................................................................................................3
Using the Timer.............................................................................................................4
Operating the BlissLights Spright Smart ............................................................5
Product Specications...............................................................................................5
Limited Warranty .........................................................................................................6
Registration Card.........................................................................................................6

NOTICE
CAUTION—Use of controls or adjustments or performance of procedures other than those
specied herein may result in hazardous radiation exposure.
This laser product is certied as CLASS 2 laser product to the requirements of the US
Federal Laser Product Performance Standard (FLPPS) contained in the regulations in 21 CFR
Subchapter J. CLASS 2 laser products can be hazardous when directly viewed.
Avoid direct viewing of a CLASS 2 laser energy. For reference the FLPPS requirements
for demonstration laser products like laser pointers are limited to CLASS 2 levels of laser
energy. This product uses diractive optics to scatter the beam energy. This scattering
eect causes the energy concentration to drop below the exposure limits for momentary or
accidental viewing at a relatively short distance from the laser aperture. As similar with all
bright light sources, when you operate this device in unsupervised general public areas, it is
recommended that up close access to the BlissLights be restricted or prevented.
This laser display device incorporates a CLASS 2 laser system which, by itself, may be
hazardous. However, this laser display device incorporates a protective housing and
diractive holographic optics in the machine design such that there is no exposure or
human access to laser radiation during operation or maintenance above the CLASS 2 limits.
Each individual laser beam power is under 1mw which is less than a standard laser pointer.
UNDER NO CIRCUMSTANCE shall attempts be made to open the protective housing or
operate the device if the aperture windows are damaged.
All service to this laser display device requiring the protective housing to be opened and/
or removed shall be performed by BlissLights service personnel or their authorized agents.
Opening the BlissLights protective housing voids the warranty.
NO LASERS SHOULD BE POINTED INTO THE SKY WITHIN 10 NAUTICAL MILES
OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE
RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO STRAY BEAMS
ARE PROJECTED INTO THE AIR. CHECK WITH YOUR LOCAL AIRPORT OR COUNTY
GUIDELINES FOR FURTHER INFORMATION.
1

INTRODUCTION
Thank you for purchasing the BlissLights Spright Smart. The BlissLights Spright Smart holds
all the great qualities of the original BlissLights Spright and projects a static “rey” eect,
but has been redesigned with a new housing. The new commercial grade design is made
out of binary resin making it lighter and extra weather resistant in environments near water.
We hope you enjoy this unique lighting experience.
Each unit provides over 900 square feet of coverage which replaces 6 standard landscape
lighting xtures or hundreds of feet of rope lighting. With an average electrical usage of just
3 Watts in temperatures above 55°F (13°C), and 10 Watts in temperatures below 55°F (13°C),
it is perfect for year-round use.
BEFORE YOU BEGIN
Immediately upon receiving the xture: carefully unpack the carton packaging; check the
contents to ensure that all parts are present and are in good condition. Notify the shipper
immediately and retain packing material for inspection if any parts appear damaged from
shipping or the carton itself shows signs of mishandling. Save the carton and all packing
materials. In the event that the xture must be returned to the factory, it is important
that the xture be returned in the original factory box. Please see parts list below for box
contents.
PARTS LIST:
1) 1 x BlissLights Spright Smart
2) 1 x Transformer
3) 1 x Stake
4) 1 x Timer
2
1
3
2
4

3
SETTING UP THE BLISSLIGHTS SPRIGHT SMART
Before operating your Spright Smart, please read the“Before you Begin” section and “Notice”section of this
user guide.
STEP 1 : First locate the 2-prong plug
connected to the cable exiting the
BlissLights Spright Smart head. If using the
timer, plug this end into the matching hole
on the end of the timer and screw the cap
on to complete the water tight seal. Then
plug the two prong connector on the timer
into the matching holes on the end of the
12V Manufacturer provided transformer.
Screw the cap to complete the water tight
seal. Next plug the standard 3-prong plug
on the other end of the transformer into an
outdoor/Indoor outlet.
STEP 2 : Stake the BlissLights Spright Smart
into the desired location. To attach or
detach the stake, twist the stake into place
on the bottom of the Spright Smart. Do
not use xture head to stake light into
the ground, grasp by stake only. Use the
thumb screw on the side of the xture to
adjust the angle.
INSTALLATION TIPS
• For scheduled or nighttime-only operation, use with a timer. Do not connect the
light to a dimmer pack, it will damage the light. Use with manufacturer provided
transformer only.
• The darker the area the light is being used in, the brighter the projection. Try to stay
away from areas with street lights or other bright lights.
• If you are going to hang the BlissLights Spright Smart, it is recommended that, for
safety purposes, your lights are properly mounted using a suitable hanging clamp and
safety cable.
• The BlissLights Spright Smart will cover an area of about 30’X 30’ for every 10 feet
away from surface (equivalent to the size of about 2 two-car garages).
1
2

USING THE TIMER
This star-eld projector includes an optional 6/18 ‘in-line’ timer accessory you may use
for automatic on/o operation of the xture on a daily basis. The timer accessory is NOT
required to operate the projector, but merely included as a convenience - you may choose
to turn the projector on/o manually by unplugging/plugging it in, or incorporate the
projector to an existing group of lights already controlled by a single timer.
To incorporate the timer accessory into your BlissLight setup:
(1) Plug the 2-prong connector at the end of the lamphead cord into the 2-prong receptor
connector on the bottom of the timer box.
(2) Plug the 2-prong connector at the end of the timer cord into the 2-prong receptor
connector on the bottom of the AC adaptor box.
(3) Plugging the AC adaptor cord into any outdoor/indoor standard 120V AC outlet will
immediately activate the timer to turn the light on for 6 hours and o for 18 hours so that it
automatically goes on and o at the same time every evening until you change your mind
or disengage the timer from the setup.
IMPORTANT NOTE: IF YOU WANT TO TEST THE PROJECTOR’S PROPER FUNCTION, REMOVE
THE TIMER ASSEMBLY FIRST AND PLUG THE PROJECTOR DIRECTLY INTO ANY STANDARD AC
OUTLET TO TEST.
4
1
2
3

PRODUCT SPECIFICATIONS
BlissLights Spright Smart
Laser Classication Class 2
Maximum Laser Power
(Single Beam) Less than 1 mW
Laser Wavelength 532 nm – Green/ 455 nm -Blue / 660nm—Red
Power Consumption Up to 10 watts
Power Input 110/120V
(when used with
manufacturer provided
transformer)
Operation Indoor / Outdoor
Operating Temperature -15°F to 90°F (-26°C to 32°C)
Projection Coverage 30ft. X 30 ft.
Maintenance Maintenance Free
Warranty Limited 1 Year
5
3 feet
1 foot
3 feet of coverage for every 1 foot of throw
OPERATING THE BLISSLIGHTS SPRIGHT SMART
The BlissLights Spright Smart operates in temperatures of -15°F to 90°F (-26°C to 32°C).
There may be a slight delay if operating in temperatures below 55°F (13°C). Please allow up
to 10 minutes for light to warm up and reach its full projection.

LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in materials and workmanship for a period of one (1) year from
date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse,
abuse, accident, modications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to
have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product.
This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty
installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the nish on any
portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not
warrant and specially disclaims any warranty, whether expressed or implied, of tness for a particular purpose, other than the
warranty contained herein. The manufacturer specically disclaims any liability and shall not be liable for any consequential or
incidental loss of damage, including any labor/expense costs involved in the replacement or repair of said product. Please contact
BlissLights at [email protected], or (626) 709- 3319.
Owner Registration Card
Please ll out, cut along dashed line, ax proper postage and return this Owner Registration Card within 10 days to insure that
your new BlissLights Spright Smart is covered by the limited warranty. You can also register your product online by going to
www.blisslights.com.
Mailing Address: BlissLights, 1155 Industrial Avenue, Escondido, CA 92029
Purchaser’s Name: _________________________________________________________
Address: _______________________________________________________________
State / Province: ________________________________ Zip: ______________________
Email: ________________________________________________________________
BlissLights Product: ________________________ Purchase Date: ______________________
Where Purchased (Store Name) _________________________________________________
Where will the BlissLights be used: _______________________________________________
If commercial institution, what type of business?
q Restaurant q Bar q Store q Oce q Other: ____________________________________
If home installation, where?
q Walkway q Patio q Garden Area q Porch q Other: ________________________________
Model/UPC Number:________________________________________________________
6