Blizzard Lighting BladeRunner RGBW User manual

Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Copyright (c) 2014
TM
rgbw

Page 2
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
TABLE OF CONTENTS
BladeRunner™ RGBW Moving Head Fixture 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The BladeRunner™ RGBW 5
Main Features 5
Control 5
DMX Quick Reference 5
The BladeRunner™ RGBW Pin-up Picture 7
3. Setup 8
Fuse Replacement 8
Connecting A Bunch Of BladeRunner™ RGBW Fixtures 8
Data/DMX Cables 8
Cable Connectors 9
3-Pin??? 5-Pin??? Huh? 9
Take It To The Next Level: Setting up DMX Control 9
Fixture Linking (Master/Slave Mode) 10
Mounting/Rigging 10
Lighting Stand Mounting 10
4. Operating Adjustments 11
Navigating The Control Panel 11
Control Panel Menu Structure 11
DMX Mode 12
Set The DMX Starting Address 12
DMX Mode Selection 12
Slave Mode 12
Stand-Alone, Master/Slave, Sound Active Modes 12
PRO-Movement 12
Speed Settings 12
Auto Mode 12
Sound Active Mode 12
Manual Color Adjustments 13
Program Mode 13
LCD Display 13
Version 13
Reset 13
DMX Channel Values In-Depth 14
5. Appendix 16
A Quick DMX Lesson 16
Troubleshooting 16
Keeping Your BladeRunner™ RGBW As Good As New 17
Returns (Gasp!) 17
Shipping Issues 17
Tech Specs 18
Dimensional Drawings 19

Page 3
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x BladeRunner™ Moving Head Fixture
• 2 x Omega 1/4 Turn Mounting Brackets
• 1 x Stand Mounting Bracket
• An Ever-So-Handy Power Cord
• This Lovely User Manual
Getting It Out Of The Box
Congratulations! You have just purchased a totally unique, stunning quad-beam RGBW
moving head xture that’s guaranteed to turn heads anywhere it goes (and tilt them too)!
So now that you’re the proud owner of a BladeRunner™ (or hopefully, BLADERUNNERS!),
you should carefully unpack the box and check the contents to ensure that all parts are
present and in good condition. If anything looks as if it has been damaged in transit, notify
the shipper immediately and keep the packing material for inspection. Again, please save
the carton and all packing materials. If a xture must be returned to the factory, it is
important that the xture be returned in the original factory box and packing.
Powering Up!
All xtures must be powered directly off a switched circuit and cannot be run off a
rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
channel is used solely for a 0% to 100% switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so please verify that the
xture you receive is suitable for your local power supply. See the label on the xture or
refer to the xture’s specications chart for more information. A xture’s listed current
rating is its average current draw under normal conditions. Check the xture or device
carefully to make sure that if a voltage selection switch exists that it is set to the correct
line voltage you will use.
Warning! Verify that the voltage select switch on your unit matches the line
voltage applied. Damage to your xture may result if the line voltage applied does
not match the voltage indicated on the voltage selector switch. All xtures must
be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email. We’ll be happy to
help, honest.
Blizzard Lighting
N16 W23390 Stoneridge Dr. Ste E
Waukesha, WI 53118 USA
www.blizzardlighting.com
414-395-8365
Email: [email protected]
Disclaimer: The information and specications contained in this document are subject
to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any
errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the
right to update the existing document or to create a new document to correct any errors
or omissions at any time. You can download the latest version of this document from www.
blizzardlighting.com.
Author: Date: Last Edited: Date:
J. Thomas 4/4/2014 J. Thomas 4/17/2014

Page 4
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the
decal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
cord. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at
[email protected].

Page 5
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
2. MEET THE BLADERUNNER™ RGBW
MAIN FEATURES:
• 4x moving heads, each with 1x CREE® 10w R/G/B/W 4-in-1 LED
• Blazing fast 540° pan and 240° tilt
• User selectable 14 or 32 DMX channels
• Full RGBW color in standalone & DMX mode
• Narrow 2 degree beam angle
• Outstanding quad beam effects
• Built-in sound active programs
• Built-in automated programs via master/slave
• Built-in sound activated programs via master/slave
• 3-pin male input and 3-pin female output
• PowerCon™ compatible AC power In/Out connectors
CONTROL:
• USITT DMX-512 (14/32 Channels)
• 3-pin Input/Output
• 4-button menu with LCD display
DMX Quick Reference (14-Channel Mode)
Channel What is does
1 Dimmer (0% <--> 100%)
2 Strobe (slow <--> fast)
3 Red Intensity (0% <--> 100%)
4 Green Intensity (0% <--> 100%)
5 Blue Intensity (0% <--> 100%)
6 White Intensity (0% <--> 100%)
7 Static Colors + Color Snap/Fade
8 Built-in Programs + Sound Active
9 Built-in Program Speed (slow <--> fast)
10 Global Pan
11 Global Tilt
12 Pan Speed (fast <--> slow)
13 Tilt Speed (fast <--> slow)
14 Motor Reset (246-255)

Page 6
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
DMX Quick Reference (32-Channel Mode)
Channel What is does
1 Dimmer (0% <--> 100%)
2 Strobe (slow <--> fast)
3 1st Head Red Intensity (0% <--> 100%)
4 1st Head Green Intensity (0% <--> 100%)
5 1st Head Blue Intensity (0% <--> 100%)
6 1st Head White Intensity (0% <--> 100%)
7 2nd Head Red Intensity (0% <--> 100%)
8 2nd Head Green Intensity (0% <--> 100%)
9 2nd Head Blue Intensity (0% <--> 100%)
10 2nd Head White Intensity (0% <--> 100%)
11 3rd Head Red Intensity (0% <--> 100%)
12 3rd Head Green Intensity (0% <--> 100%)
13 3rd Head Blue Intensity (0% <--> 100%)
14 3rd Head White Intensity (0% <--> 100%)
15 4th Head Red Intensity (0% <--> 100%)
16 4th Head Green Intensity (0% <--> 100%)
17 4th Head Blue Intensity (0% <--> 100%)
18 4th Head White Intensity (0% <--> 100%)
19 Static Colors + Color Snap/Fade
20 Built-in Programs + Sound Active
21 Built-in Program Speed (slow <--> fast)
22 1st Head Pan Motor
23 1st Head Tilt Motor
24 2nd Head Pan Motor
25 2nd Head Tilt Motor
26 3rd Head Pan Motor
27 3rd Head Tilt Motor
28 4th Head Pan Motor
29 4th Head Tilt Motor
30 Pan Speed (0% <--> 100%)
31 Tilt Speed (0% <--> 100%)
32 Motor Reset (246-255)

Page 7
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
DMX Out
Power In Power Out
DMX In
Figure 1: The BladeRunner™ RGBW Pin-Up Picture
Figure 2: The Rear Connections
4x Mini Moving Heads,
each tted with 1x CREE®
High Output RGBW
10-watt LED.
Power Switch
LED
Control
Panel
Stand
Mounting
Bracket
Bracket
Mounting Holes
Bracket
Mounting Holes Rubber
Feet
Rubber
Feet

Page 8
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
CAUTION! The BladeRunner™ RGBW utilizes a high-output switch-
mode power supply with an internal fuse. Under normal operating
conditions, the fuse should not require replacement. The fuse is eld
replaceable, however it is an advanced procedure suited to qualied
individuals. Should your BladeRunner™ RGBW fuse require replacement,
please contact Blizzard Lighting for instructions, or to return your unit for
service.
Connecting A Bunch of BladeRunner™ RGBW Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in master/
slave operating mode. The combined number of channels required by all
the xtures on a serial data link determines the number of xtures the
data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without the
use of a DMX optically-isolated splitter may result in deterioration of the
digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640 ft).
The maximum recommended number of xtures on a serial data link is
32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-485
applications. Standard microphone cables will “probably” be OK, but note
that they cannot transmit DMX data as reliably over long distances. In
any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms

Page 9
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the
xture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers. If you’d like to build your own,
the chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of
the DMX cable to the rst xture’s male
connector (input). Note: It doesn’t matter
which xture address is the rst one
connected. We recommend connecting the
xtures in terms of their proximity to the
controller, rather than connecting the lowest
xture number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.

Page 10
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the DMX cable to the output
(female) 3 pin connector of the rst xture.
2. Connect the end of the cable coming from the rst xture which will have a
(female) 3 pin connector to the input connector of the next xture consisting of
a (male) 3 pin connector. Then, proceed to connect from the output as stated
above to the input of the following xture and so on.
A quick note: Often, the setup for Master-Slave and Standalone operation
requires that the rst xture in the
chain be initialized for this purpose
via either settings in the control
panel or DIP-switches. Secondarily,
the xtures that follow may also
require a slave setting.
Check the “Operating
Adjustments” section in this
manual for complete instructions
for this type of setup and
conguration.
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is enough
room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the xture
using a suitable “C” or “O” type clamp. The clamp should be rated to hold at
least 10x the xture’s weight to ensure structural stability. Do not mount to
surfaces with unknown strength, and ensure properly “rated” rigging is used
when mounting xtures overhead.
Adjust the angle of the xture by loosening both knobs and tilting the xture.
After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain, high
humidity, extreme temperature changes or restricted ventilation.
Lighting Stand Mounting
This xture comes with an easy to use stand mounting bracket. Please make
sure the lighting stand you use is rated to safely hold the weight of this unit and
do not over-extend the lighting stand. For the safety of yourself, your audience,
and the xture... always take advantage of the use of the stand’s safety pins!

Page 11
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS
The Control Panel
All the goodies and different modes possible with the BladeRunner™ RGBW are accessed
by using the control panel on the front of the xture. There are 4 control buttons below
the LCD display which allow you to navigate through the various control panel menus.
Main Menu
To navigate through the LCD control panel main menu, use the <MENU> button to scroll
through the various top level menu options. Then to scroll through sub-menu options, use
the <UP/DOWN> buttons. Push the <ENTER> button to save any changes made.
MENU ENTERDOWNUP
Control Panel Menu Structure
Address 001-512 DMX Address
CHND 14CH 14 Channel DMX Mode
32CH 32 Channel DMX Mode
AUTO STOP/RUN Auto Mode (slower color changing)
AUTO 1 STOP/RUN Auto Mode (faster color changing)
AUDIO STOP/RUN Sound Active Mode
COLOR Red 1 Head 1 - Red (0-255)
Green 1 Head 1 - Green (0-255)
Blue 1 Head 1 - Blue (0-255)
White 1 Head 1 - White (0-255)
Red 2 Head 2 - Red (0-255)
Green 2 Head 2 - Green (0-255)
Blue 2 Head 2 - Blue (0-255)
White 2 Head 2 - White (0-255)
Red 3 Head 3 - Red (0-255)
Green 3 Head 3 - Green (0-255)
Blue 3 Head 3 - Blue (0-255)
White 3 Head 3 - White (0-255)
Red 4 Head 4 - Red (0-255)
Green 4 Head 4 - Green (0-255)
Blue 4 Head 4 - Blue (0-255)
White 4 Head 4 - White (0-255)
Shut Strobe Rate (0-255)
PROGRAM 01-20 Built-in Programs
PRO-Movement ON/OFF Auto Movement On/Off
SPEED <ENTER> Speed Settings
Movement Movement Speed (001-255)
Color Color Speed (001-255)
LED ON/OFF LCD Backlight On/Off
VERSION V1.0.0 Firmware Version
RESET Yes? Fixture Reset

Page 12
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
DMX Mode
Allows the unit to be controlled by any universal DMX controller.
Set The DMX Starting Address
To assign a DMX staring address to the xture, use the <MENU> button to scroll to Address,
then use the <UP/DOWN> buttons to display any value within the range of 001-512. Then
push the <ENTER> button to conrm your choice.
DMX Mode Selection
To use the xture in either of its two DMX channel mode congurations, use the <MENU>
button to scroll to CHND, then use the <UP/DOWN> buttons to display either 14CH or 32CH.
Then push the <ENTER> button to conrm your choice.
Slave Mode
1.) Disconnect xture(s) from any DMX signal source.
2.) Set each xture to matching DMX modes (14CH or 32CH).
3.) Connect all xtures together via DMX. The rst xture in the DMX chain will be the master
xture, followed by the slave xtures.
4.) Connect DMX controller to the master unit for DMX control.
Stand-Alone, Master/Slave, Sound Active Modes:
Allows a single or Master/Slaved units to run factory installed programs at user selectable speeds.
PRO-Movement
This allows you to enable/disable auto movement of the heads in Program Mode or within Manual
Color Adjustments. This will not effect movement in Auto or DMX modes.
1.) Use the <MENU> button to scroll to PRO-Movement, then use the <UP/DOWN> buttons
to display either ON or OFF. Then push the <ENTER> button to conrm your choice.
Speed Settings
This allows you to adjust the speed of the moving heads and color macros in Program Mode, Auto
Mode or within Manual Color mixing. This will not effect speed in DMX mode.
1.) Use the <MENU> button to scroll to SPEED, then use the <UP/DOWN> buttons to display
either Movement or Color, then push the <ENTER> button. You can now adjust the speed
settings from 001-255 (slow <--> fast).
Auto Mode
To run the xture in auto mode, use the <MENU> button to scroll to AUTO or AUTO 1, then
push the <ENTER> button to conrm. You then adjust the movement and color macro speed
settings of the auto mode program (see Speed Settings).
Sound Active Mode
To run the xture in sound active mode, use the <MENU> button to scroll to AUDIO, then push
the <ENTER> button to conrm.

Page 13
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Manual Color Adjustment
Allows the user to adjust the color balance of each individual moving head xture. You can set your own
intensity levels and then add PRO-Movement if you like! (See p. 12).
1.) Use the <MENU> button to scroll to COLOR, then use the <UP/DOWN> buttons to display
any of Red, Green, Blue, or White settings for xtures 1, 2, 3, and 4. Push the <ENTER> button
while highlighting any to display the color intensity range settings from 000-255. Use the <UP/
DOWN> buttons to adjust the intensity, then push <ENTER> to conrm your choice.
2.) The last option in the COLOR submenu is Shut (strobe). Using the same steps as above,
you can adjust the strobe rate values from 000-255 (slow <--> fast).
Program Mode
Allows a single unit to display a variety of colors and programs without a DMX controller.
1.) Use the <MENU> button to scroll to PROGRAM, then use the <UP/DOWN> buttons to
display the built-in program number from 01-20. Push the <ENTER> to conrm your choice. If
you wish, you can then also enable/disable PRO-Movement, or adjust the Speed Settings of the
Movement or Color Macros. (See p. 12)
LCD Display
To turn on/off the backlit LCD display, use the <MENU> button to scroll to LED, then push
<ENTER>. Then use the <UP/DOWN> buttons to scroll or either ON or OFF, and push
<ENTER> button to conrm your choice. ON will leave the display illuminated constantly, and
OFF will turn the display off after 40 seconds of idle.
Version
This menu option simply displays the xtures installed rmware version number.
Reset
To automatically reset the motors to automatically realign the moving head positions, use the
<MENU> button to scroll to RESET, then push <ENTER>.

Page 14
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
DMX Values In-Depth (14-Channel Mode)
Channel Value What It Does
1 000 <--> 255 Dimmer (0% <--> 100%)
2 000 <--> 255 Strobe (Slow <--> Fast)
3 000 <--> 255 Red Intensity (0% <--> 100%)
4 000 <--> 255 Green Intensity (0% <--> 100%)
5 000 <--> 255 Blue Intensity (0% <--> 100%)
6 000 <--> 255 White Intensity (0% <--> 100%)
7
000 <--> 028
029 <--> 057
058 <--> 086
087 <--> 115
116 <--> 144
145 <--> 173
174 <--> 202
203 <--> 204
205 <--> 229
230 <--> 255
Static Colors + Color Snap/Fade
Red
Green
Blue
White
Red+Green
Green+Blue
Red+Blue
Red+Green+Blue+White
Color Snap
Color Fade
8
000 <--> 012
013 <--> 025
026 <--> 038
039 <--> 051
052 <--> 064
065 <--> 077
078 <--> 091
092 <--> 103
104 <--> 116
117 <--> 129
130 <--> 142
143 <--> 155
156 <--> 168
169 <--> 181
182 <--> 194
195 <--> 207
208 <--> 220
221 <--> 233
234 <--> 246
247 <--> 250
251 <--> 255
Built-In Programs + Sound Active
Red
Green
Blue
White
Red+Green
Green+Blue
Red+Blue
Red+Green+Blue+White
Color Snap
Color Fade
Red+Green+Blue+White+Strobe (slow)
Red+Green+Blue+White+Strobe (fast)
Red Chase (1 head on, back and fourth)
R/G/B/W Chase (1 head on, left to right)
R/G/B/W Chase (1 head on, back and fourth)
Green Chase (1 head on, left to right)
Green Chase (1 head on, back and fourth)
R/G/B/W Color Chase, Head 1+2 | 3+4 (all on)
R/G/B/W Color Chase, Head 1+3 | 2+4 (all on)
R/G/B/W Color Chase (all on)
Sound Active Mode
9 000 <--> 255 Color Macro Speed (0% <--> 100%)
10 000 <--> 255 Pan
11 000 <--> 255 Tilt
12 000 <--> 255 Pan Speed (fast <--> slow)
13 000 <--> 255 Tilt Speed (fast <--> slow)
14 000 <--> 245
246 <--> 255
No Function
Reset Motors
DMX Values In-Depth (32-Channel Mode)
Channel Value What It Does
1 000 <--> 255 Dimmer (0% <--> 100%)
2 000 <--> 255 Strobe (Slow <--> Fast)
3 000 <--> 255 1st Head - Red Intensity (0% <--> 100%)
4 000 <--> 255 1st Head - Green Intensity (0% <--> 100%)
5 000 <--> 255 1st Head - Blue Intensity (0% <--> 100%)
6 000 <--> 255 1st Head - White Intensity (0% <--> 100%)

Page 15
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
DMX Values In-Depth (32-Channel Mode, continued)
Channel Value What It Does
7 000 <--> 255 2nd Head - Red Intensity (0% <--> 100%)
8 000 <--> 255 2nd Head - Green Intensity (0% <--> 100%)
9 000 <--> 255 2nd Head - Blue Intensity (0% <--> 100%)
10 000 <--> 255 2nd Head - White Intensity (0% <--> 100%)
11 000 <--> 255 3rd Head - Red Intensity (0% <--> 100%)
12 000 <--> 255 3rd Head - Green Intensity (0% <--> 100%)
13 000 <--> 255 3rd Head - Blue Intensity (0% <--> 100%)
14 000 <--> 255 3rd Head - White Intensity (0% <--> 100%)
15 000 <--> 255 4th Head - Red Intensity (0% <--> 100%)
16 000 <--> 255 4th Head - Green Intensity (0% <--> 100%)
17 000 <--> 255 4th Head - Blue Intensity (0% <--> 100%)
18 000 <--> 255 4th Head - White Intensity (0% <--> 100%)
19
000 <--> 028
029 <--> 057
058 <--> 086
087 <--> 115
116 <--> 144
145 <--> 173
174 <--> 202
203 <--> 204
205 <--> 229
230 <--> 255
Static Colors + Color Snap/Fade
Red
Green
Blue
White
Red+Green
Green+Blue
Red+Blue
Red+Green+Blue+White
Color Snap
Color Fade
20
000 <--> 012
013 <--> 025
026 <--> 038
039 <--> 051
052 <--> 064
065 <--> 077
078 <--> 091
092 <--> 103
104 <--> 116
117 <--> 129
130 <--> 142
143 <--> 155
156 <--> 168
169 <--> 181
182 <--> 194
195 <--> 207
208 <--> 220
221 <--> 233
234 <--> 246
247 <--> 250
251 <--> 255
Built-In Programs + Sound Active
Red
Green
Blue
White
Red+Green
Green+Blue
Red+Blue
Red+Green+Blue+White
Color Snap
Color Fade
Red+Green+Blue+White+Strobe (slow)
Red+Green+Blue+White+Strobe (fast)
Red Chase (1 head on, back and fourth)
R/G/B/W Chase (1 head on, left to right)
R/G/B/W Chase (1 head on, back and fourth)
Green Chase (1 head on, left to right)
Green Chase (1 head on, back and fourth)
R/G/B/W Color Chase, Head 1+2 | 3+4 (all on)
R/G/B/W Color Chase, Head 1+3 | 2+4 (all on)
R/G/B/W Color Chase (all on)
Sound Active Mode
21 000 <--> 255 Color Macro Speed (0% <--> 100%)
22 000 <--> 255 1st Head - Pan
23 000 <--> 255 1st Head - Tilt
24 000 <--> 255 2nd Head - Pan
25 000 <--> 255 2nd Head - Tilt
26 000 <--> 255 3rd Head - Pan
27 000 <--> 255 3rd Head - Tilt
28 000 <--> 255 4th Head - Pan
29 000 <--> 255 4th Head - Tilt
30 000 <--> 255 Pan Speed (fast <--> slow)
31 000 <--> 255 Tilt Speed (fast <--> slow)
32 000 <--> 245
246 <--> 255
No Function
Reset Motors

Page 16
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
5. APPENDIX
A Quick Lesson On DMX
DMX covers (and is an abbreviation for) Digital MultipleXed signals. It is the most common
communications standard used by lighting and related stage equipment.
DMX provides up to 512 control “channels” per data link. Each of these channels was
originally intended to control lamp dimmer levels. You can think of it as 512 faders on a
lighting console, connected to 512 light bulbs. Each slider’s position is sent over the data
link as an 8-bit number having a value between 0 and 255. The value 0 corresponds to the
light bulb being completely off while 255 corresponds to the light bulb being fully on.
DMX data is transmitted at 250,000 bits per second using the RS-485 transmission
standard over two wires. As with microphone cables, a grounded cable shield is used to
prevent interference with other signals.
There are ve pins on a DMX connector: a wire for ground (cable shield), two wires for
“Primary” communication which goes from a DMX source to a DMX receiver, and two
wires for a “Secondary” communication which goes from a DMX receiver back to a DMX
source. Generally, the “Secondary” channel is not used so data ows only from sources
to receivers. Hence, most of us are most familiar with DMX-512 as being employer over
typical 3-pin “mic cables,” although this does not conform to the dened standard.
DMX is connected using a daisy-chain conguration where the source connects to the input
of the rst device, the output of the rst device connects to the input of the next device,
and so on. The standard allows for up to 32 devices on a single DMX link.
Each receiving device typically has a means for setting the “starting channel number” that
it will respond to. For example, if two 6-channel xtures are used, the rst xture might
be set to start at channel 1 so it would respond to DMX channels 1 through 6, and the next
xture would be set to start at channel 7 so it would respond to channels 7 through 12.
Troubleshooting
Symptom Solution
Fixture Auto-
Shut Off
Check the fan in the xture. If it is stopped or moving slower than
normal, the unit may have shut itself off due to high heat. This is to
protect the xture from overheating. Clear the fan of obstructions,
or return the unit for service.
Beam is Dim Check optical system and clean excess dust/grime. Also ensure that
the 220V/110V switch is in the correct position, if applicable.
No Light Output Check to ensure xture is operating under correct mode, IE sound
active/auto/DMX/Etc., if applicable. Contact service for more infor-
mation.
Chase Speed Too
Fast/Slow
Check to ensure proper setup of speed adjustment.
No Power Check fuse, AC cord and circuit for malfunction.
No Response to
Audio
Verify that the xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.
Fixture Not
Responding /
Responding Er-
ratically
Make sure all connectors are seated properly and securely.
Use Only DMX Cables.
Install a Terminator.
Check all cables for defects.
Reset xture(s).

Page 17
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Keeping Your BladeRunner™ RGBW As Good As New
The xture you’ve received is a rugged, tough piece of pro lighting equipment,
and as long as you take care of it, it will take care of you. That said, like
anything, you’ll need to take care of it if you want it to operate as designed.
You should absolutely keep the xture clean, especially if you are using it in an
environment with a lot of dust, fog, haze, wild animals, wild teenagers or spilled
drinks.
Cleaning the optics routinely with a suitable glass cleaner will greatly improve
the quality of light output. Keeping the fans free of dust and debris will keep
the xture running cool and prevent damage from overheating.
In transit, keep the xtures in cases. You wouldn’t throw a prized guitar,
drumset, or other piece of expensive gear into a gear trailer without a case,
and similarly, you shouldn’t even think about doing it with your shiny new light
xtures.
Common sense and taking care of your xtures will be the single biggest thing
you can do to keep them running at peak performance and let you worry about
designing a great light show, putting on a great concert, or maximizing your
client’s satisfaction and “wow factor.” That’s what it’s all about, after all!
Returns (Gasp!)
We’ve taken a lot of precautions to make sure you never even have to worry
about sending a defective unit back, or sending a unit in for service. But,
like any complex piece of equipment designed and built by humans, once in a
while, something doesn’t go as planned. If you nd yourself with a xture that
isn’t behaving like a good little xture should, you’ll need to obtain a Return
Authorization (RA).
Don’t worry, this is easy. Just send an email to [email protected],
and we’ll issue you an RA. Then, you’ll need to send the unit to us using a
trackable, pre-paid freight method. We suggest using USPS Priority or UPS.
Make sure you carefully pack the xture for transit, and whenever possible, use
the original box & packing for shipping.
When returning your xture for service, be sure to include the following:
1.) Your contact information (Name, Address, Phone Number, Email address).
2.) The RA# issued to you
3.) A brief description of the problem/symptoms.
We will, at our discretion, repair or replace the xture. Please remember
that any shipping damage which occurs in transit to us is the customer’s
responsibility, so pack it well!
Shipping Issues
Damage incurred in shipping is the responsibility of the shipper, and
must be reported to the carrier immediately upon receipt of the items.
Claims must be made within seven (7) days of receipt.

Page 18
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Tech Specs!
Weight & Dimensions
Length 40.5 inches (102.9 cm)
Height 8.25 inches (21 cm)
Depth Base: 3.27” (8.3 cm), Head: 5” (12.7 cm)
Weight 22.1 lbs (10 kg)
Power
Operating Voltage AC 110-240VAC, 50-60 Hertz
Power Consumption 77w, 1.13A
Power Factor .6
Light Source
LED 4* 10-watt R/G/B/W CREE® LEDs
Optical
Beam Angle 2 degree
Thermal
Max. Operating
Temp.
104 degrees F (40 degrees C) ambient
Control
Protocol USITT DMX-512
DMX Channels 14 or 32 Channels
Input 3-pin XLR Male
Output 3-pin XLR Female
Other Operating
Modes Standalone, Master/Slave, Auto, Sound Active
Other Information
If you have a pear shaped body, you should not wear pear colored
clothes, or act juicy.
Warranty
2-year limited warranty, does not cover mal-
function caused by damage to LED’s.
DISCLAIMER:
The power connector tted to the xture and xture cord are designed for compatibility
with products manufactured by Neutrik AG, Neutrik USA and their related entities, how-
ever they are not manufactured by, afliated with or endorsed by Neutrik AG, Neutrik
USA, or any related entity. Neutrik® and powerCON® are registered trademarks of
Neutrik AG.

Page 19
BladeRunner™ RGBW User Manual Rev. A (c) Copyright 2014 Blizzard Lighting, LLC
Luminous Intensity
Lux/Meter 1 Meter 2 Meter
Red 10,270 Lux 3,460 Lux
Green 13,590 Lux 4,700 Lux
Blue 15,560 Lux 6,050 Lux
White 21,000 Lux 6,700 Lux
Dimensional Drawings
40.5 in
8.25 in
3.27 in
3.27 in
5 in
4.8 in

Enjoy your product!
Our sincerest thanks for your purchase!
--The team @ Blizzard Lighting