Blodgett KTG-E Guide

1
KTG-E
ELECTRIC TABLE TOP KETTLE WITH MANUAL
GEARBOX TILT MECHANISM
INSTALLATION –OPERATION –MAINTENANCE
BLODGETT OVEN COMPANY
www.blodgett.com
44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: [phone] Fax: [phone]
S00062 Rev A (5/04)

2
IMPORTANT NOTES FOR INSTALLATION AND OPERATION
It is recommended that this manual be read thoroughly and that all instructions be followed
carefully.
This manual should be retained for future reference.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
WARNING: Improper installation, operation, adjustment, alteration,
service or maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions
thoroughly before installing, operating or servicing this equipment.
Do not attempt to operate this unit in the event of a power failure.
Adequate clearances must be maintained for servicing and proper operation.
Intended for commercial use only. Not for household use.
NOTICE: Contact the factory, the factory representative or local service
company to perform maintenance and repairs.

3
TABLE OF CONTENTS
DESCRIPTION PAGE
IMPORTANT NOTES FOR INSTALLATION AND OPERATION ....................................... 2
SERVICE CONNECTIONS ...............................................................................................4
1.0 INSTALLATION INSTRUCTIONS ..............................................................................5
2.0 INTRODUCTION ........................................................................................................7
3.0 OPERATING INSTRUCTIONS ...................................................................................8
4.0 CLEANING INSTRUCTIONS ...................................................................................10
5.0 MAINTENANCE ....................................................................................................... 11
6.0 TROUBLESHOOTING ............................................................................................. 12
APPENDIX „A‟, MATERIAL SAFETY DATA SHEET ........................................................ 13

4
SERVICE CONNECTIONS
A ID
B
C
14 1/2 [368]
20 7/8 [530]
4X WELD NUTSP5/16-18UNC 10 [254]
12 1/2 [318]
1 1/4 [32]
G
2 1/8 [54] K
H
J
F
D
1 7/8 [48]
SAFETY RELIEF VALVE
E
ELECTRICAL CONNECTION TO BE AS SPECIFIED ON DATA PLATE
-
CAPACITY
10 gallons
12 gallons
MODEL
KTG-10E
KTG-12E
25 5/16
700
27 9/16
643
UNITS
45 litres
38 litres mm
mm
CA B
438
381
406
16
17 1/4
15
DIMENSIONS
ED
19 1/8
486
28 7/8
734
G
30
762
F JH
6 1/8
156
13
330102
4
K
324
12 3/4
inches
inches
23 litres
6 gallons
KTG-6E inches
mm
14 3/8
365
711
28
635
25
387
15 1/4
638
25 1/8
305
12
12 3/4
324
K
KTG-6E
KTG-10E
KTG-12E
MODEL
20.8
36.0
57.6
33.3
19.7
34.1
31.5
54.5
31.3
28.9
50.0
18.1
18.3
11.4
16.7
10.4
ELECTRICAL CHARACTERISTICS
208V 220V 240V 380V 415V
14.5
9.0
480V
AMPS PER LINE
1
12.0 3
PHASEkW
3
1
7.5 N/A
N/A
N/A
N/A
N/A
N/A

5
1.0 INSTALLATION INSTRUCTIONS
Immediately after unpacking, check for possible shipping damage. If the kettle is found to
be damaged, save the packaging materials and contact the carrier within 15 days of
delivery.
1. The kettle must be installed in accordance with:
2. State and/or local codes.
3. In the USA, the National Electrical Code, ANSI/NFPA-70 (latest edition). In Canada,
the Canadian Electrical Code, Part 1, CSA Standard C22.1 (latest edition).
4. Position appliance on counter allowing sufficient rear clearance from wall to tilt freely
and completely without obstruction.
5. Mark four corner locations of appliance base.
6. Remove appliance from counter and locate position of 4 holes as per Figure 1. Drill
four 7/16" diameter holes.
7. Use 5/16-18 Hex Cap Screws with suitable flat washers to bolt down. Screw length
must be 1-1/4 long plus counter top thickness.
8. Apply a continuous bead of Silastic or other equivalent sealant along the complete
perimeter edge of the appliance base.
9. Wipe off excess sealant.
10. A Control Box with power supply equivalent to Electrical Rating of appliance should be
located conveniently nearby.

6
1.0 INSTALLATION INSTRUCTIONS (Continued)
WARNING: Disconnect electrical power supply and place a tag
at the disconnect switch to indicate you are on the circuit.
1. A waterproof electrical connection for power supply to console housing must be
provided.
2. Ground appliance to terminal provided inside console housing.
3. Turn power ON and check for proper operation.
FIGURE 1

7
2.0 INTRODUCTION
DESCRIPTION
Models KTG-6E (6 gallon capacity) and KTG-10E (10 gallon capacity) and KTG-12E (12
gallon capacity) electrically powered, self-contained, countertop, tilting kettles. Each model
has a jacket of double-wall construction forming a sealed reservoir around the lower two-
thirds of the kettle. The reservoir is charged with distilled water and anti-freeze solution.
Kettles are equipped with a removable electric heating element and controls, including a
low water cutoff device for protection of the heating element. All models are of identical
construction, except for kettle size and element heating capacity.
BASIC FUNCTION
Self-contained kettles operate by generating steam in the kettle reservoir. The sequence of
operation is as follows:
1. Operator turns the power switch to the ON position and sets the temperature control
dial to the desired setting from 1 to 10.
2. Control circuit is normally completed to the temperature controller if the following
conditions exist:
A. Water level in the kettle reservoir is adequate to prevent circuit interruption by the
low water cut off device. An activated cutoff is indicated by the amber low water
light turning on, and the heating element shut off.
B. Kettle is in vertical position with circuit completed through the tilt interlock switch.
3. Thermostat control contacts close to energize contactor coils.
4. Power is supplied to the elements through closed power contactors.
5. As the temperature of water rises in the kettle reservoir, increase in steam pressure is
indicated on the pressure gauge.
6. When the temperature of steam in the reservoir reaches the setting of the temperature
control dial, the temperature controller opens to break the contacts and shuts off the
heating element. The heating elements will cycle on and off as required to maintain
temperature setting.

8
3.0 OPERATING INSTRUCTIONS
WARNING: The safety relief valve may discharge large amounts of
steam and/or hot water. Keep away from the discharge tube at all
times. Warn others in the area so they will not be startled by the
sound.
1. Ensure that the external electrical shut-off to the kettle is on.
2. Check pressure gauge for correct cold kettle reading. Reading should be in the green
vacuum zone. If reading is not in the vacuum zone, follow VENTING INSTRUCTIONS
prior to using the kettle.
3. Place power switch in ON position.
4. Preheat the kettle by placing thermostat knob at „10' and wait until TEMPERATURE
light goes off.
5. Add food to be cooked into the kettle.
6. Place thermostat knob at required temperature setting from 1 to 10 coinciding with a
temperature range from roughly 90F to 289F (32C to 143C, jacket temperature.)
Approximate cooking temperatures with water at various thermostat settings are as
follows:
THERMOSTAT SETTINGS
APPROXIMATE TEMPERATURE (JACKET)
FAHRENHEIT
CELSIUS
4
90
32
5
125
52
6
160
41
7
195
91
8
231
110
9
273
134
10
289
143
NOTE: Preheating should not be used when cooking milk and egg food
products which adhere to hot cooking surfaces. These foods should be
placed into kettle before heating is begun.

9
3.0 OPERATING INSTRUCTIONS (Continued)
7. When cooking is finished set thermostat knob and power switch to the OFF position.
8. Pour finished product from kettle using tilt handle. Be careful to avoid splashing.
9. Add water to kettle for cleaning purposes.
10. Wash kettle thoroughly. See CLEANING procedure.
TILTING INSTRUCTIONS
DO NOT ATTEMPT TO TILT WITH LID ON KETTLE.
1. To empty contents, turn handwheel counterclockwise to desired position.
2. To return kettle to cooking position, turn handwheel clockwise until in upright position.
NOTE: When kettle is tilted a safety switch will automatically turn off the
power supply. The kettle will not operate once the kettle has been tilted.

10
4.0 CLEANING INSTRUCTIONS
WARNING: Disconnect the power supply to the appliance before
cleaning or servicing.
The kettle interior and exterior should be thoroughly washed after each use in preparation
of a different food.
1. Add water and mild detergent to the kettle immediately after use.
2. Scrub kettle interior with nylon brush.
3. Loosen food which is stuck to kettle by allowing it to soak at a low temperature setting.
4. Rinse with clear water and dry.
WARNING: Do not hose down appliance under any condition.
Failure to comply will void warranty.
5. Wipe down exterior, rinse and dry.
CAUTION: Do not use cleaning agents that are corrosive.
Use of cleaning agents that contain chloride, acids or salts are corrosive and may cause
pitting and corrosion when used over a period of time; this will reduce the life of the
appliance.
Should pitting or corrosion occur this is not covered by warranty.
Follow the recommended cleaning instructions. Use a mild detergent, warm water and
rinse thoroughly.
NOTE: Never scrape the inside of the kettle with metal tools, steel scouring
pads, or abrasive cleaners. Scratches will result which will spoil the kettle’s
general appearance and make it harder to clean and maintain a sanitary
condition.

11
5.0 MAINTENANCE
Daily
1. Ensure there is adequate vacuum in the kettle jacket before operating.
2. Ensure that the appliance and controls are not damaged and that it can be safely
operated.
3. Ensure the work area of the operator is not slippery and is clear of debris so as to
provide a safe workplace.
4. Ensure the appliance is clean before each use.
5. Check that the LOW WATER control is operational. Tilting the kettle more than 5 or 10
degrees should cause the LOW WATER signal light to come on.
Every Two Weeks
1. Perform a “try lever test” on the safety relief valve.
WARNING: The safety relief valve may discharge large amounts of
steam and/or hot water. Keep away from the discharge tube at all
times. Warn others in the area so they will not be startled by the
sound.
Under normal operating conditions a “try lever test” must be performed every two months.
Under severe service conditions, or if corrosion and/or deposits are noticed within the valve
body, testing must be performed more often. A “try lever test” must also be performed at
the end of any non-service period.
Test at or near maximum operating pressure by holding the test lever fully open for at least
5 seconds to flush the valve seat free of sediment and debris. Then release lever and
permit the valve to snap shut.
If lift lever does not activate, or there is no evidence of discharge, discontinue use of
equipment immediately and contact a licensed contractor or qualified service personnel.
Every Six Months
1. Lubricate the bronze trunnion bearings.
2. Check the worm gearbox for evidence of oil leaks. It is permanently lubricated with
synthetic oil (Shell TIVELA OIL SC320 or equivalent) and should not require
maintenance.
3. Check that the tilt mechanism has not become loose or has excessive backlash.

12
6.0 TROUBLESHOOTING
6.1 LOW WATER LEVEL
Proper water level must be maintained within the jacket for the kettle to operate. Depletion
of water may occur from excessive opening of, or leakage through the safety relief valve.
If water is below required operating level, either initially at start-up or during use, the kettle
will automatically shut off, and the LOW WATER signal light will come on.
In order for the kettle to operate, the following procedure must be followed:
1. Trip the safety relief valve lever to relieve all pressure from the kettle jacket.
2. At exterior rear of kettle jacket remove nut from Air Vent.
3. Insert funnel into Air Vent opening and slowly add the indicated amount of distilled
water for:
KTG-6E Add 50 oz. (1.5 litres)
KTG-10E and KTG-12E Add 100 oz. (3 litres)
4. Replace Air Vent nut.
5. Follow Air Venting Instructions below.
6. Continue normal Operating Procedure of kettle.
6.2 VENTING INSTRUCTIONS
Check pressure gauge when kettle is cold. Gauge should be in the green vacuum zone. If
not, air is present which must be vented (removed) for proper heating. Use the following
procedures to vent air.
1. With an empty kettle, place power switch to the ON position.
2. Set temperature control thermostat to „10'. Heat kettle until heat indicator light goes off.
3. Using a 7/16" wrench, open bleed vent one full turn for 10 seconds and then close.
4. Cool kettle. Check for proper vacuum in the green vacuum zone. If reading is not low
enough, repeat entire procedure, steps 1 to 3.

13
APPENDIX ‘A’ MATERIAL SAFETY DATA SHEET
PREPARATION INFORMATION:
Prepared for use in Canada by: E H & S Product Regulatory Management Department
DOW CHEMICAL CANADA INC.
P.O. Box 1012
Sarnia, Ontario, N7T 7K7
[phone]
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
IN CASE OF EMERGENCY: Fort Saskatchewan, Alberta: [phone]
Sarnia, Ontario: [phone]
Varennes, Quebec: [phone]
Product: DOWFROST*HD HEAT TRANSFER FLUID, DYED
Product Code: 04632
Effective Date: 2/20/01 Date Printed: 07/10/02 MSD: 002239
DOW CHEMICAL CANADA INC.
P.O. Box 1012
Sarnia, Ontario, N7T 7K7
Prepared for use in Canada by the E H & S Product Regulatory Management Department;
Phone: [phone].
1. COMPOSITION/INFORMATION ON INGREDIENTS
Propylene Glycol CAS# 000057-55-6 94%
Dipotassium PhosphateCAS# 007758-11-4 <5%
Deionized Water CAS# 007732-18-5 <5%
* or (R) indicates a trademark of The Dow Chemical Company.
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632

14
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239
2. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
POTENTIAL HEALTH EFFECTS (See Section 11 for toxicological data.)
EYE: May cause slight transient (temporary) eye irritation. Corneal injury is unlikely. Mists
may cause eye irritation.
SKIN CONTACT: Prolonged contact is essentially nonirritating to skin. A single prolonged
exposure is not likely to result in the material being absorbed through skin in harmful
amounts. Repeated exposures may cause flaking and softening of skin.
INGESTION: Single dose oral toxicity is considered to be extremely low. No hazards
anticipated from swallowing small amounts incidental to normal handling operations.
INHALATION: At room temperature, vapours are minimal due to physical properties.
Mists may cause irritation of upper respiratory tract (nose and throat).
SYSTEMIC (OTHER TARGET ORGAN) EFFECTS: Repeated excessive exposure to
propylene glycol may cause central nervous system effects.
CANCER INFORMATION: Did not cause cancer in laboratory animals.
TERATOLOGY (BIRTH DEFECTS): Birth defects are unlikely. Exposures having no
adverse effects on the mother should have no effect on the fetus.
REPRODUCTIVE EFFECTS: In animal studies, has been shown not to interfere with
reproduction.
* or (R) indicates a trademark of The Dow Chemical Company.
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239
Clear yellow liquid. Odourless. Avoid temperatures above 450F, 232C.

15
4. FIRST AID
EYES: Flush eyes with plenty of water.
SKIN: Wash off in flowing water or shower.
INGESTION: No adverse effects anticipated by this route of exposure
incidental to proper industrial handling.
INHALATION: Remove to fresh air if effects occur. Consult a physician.
NOTE TO PHYSICIAN: No specific antidote. Supportive care. Treatment based on
judgment of the physician in response to reactions of the
patient.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
FLASH POINT: 214F, 107C (based on a similar material)
METHOD USED: PMCC
AUTOIGNITION TEMPERATURE: NOT DETERMINED
FLAMMABILITY LIMITS
LFL: Not determined
UFL: Not determined
* or (R) indicates a trademark of The Dow Chemical Company.
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239

16
HAZARDOUS COMBUSTION PRODUCTS: During a fire, smoke may contain the original
material in addition to unidentified toxic and/or irritating compounds. Hazardous
combustion products may include and are not limited to carbon monoxide and carbon
dioxide.
OTHER FLAMMABILITY INFORMATION: Violent steam generation or eruption may occur
upon application of direct water stream to hot liquids. Flammable concentrations of vapour
can accumulate at temperatures above 214F. Liquid mist of this product can burn. Spills
of these organic liquids on hot fibrous insulations may lead to lowering of the autoignition
temperatures possibly resulting in spontaneous combustion. Container may rupture from
gas generation in a fire situation.
EXTINGUISHING MEDIA: Water fog or fine spray, carbon dioxide, dry chemical, foam.
Alcohol resistant foams (ATC type) are preferred if available. General purpose synthetic
foams (including AFFF) or protein foams may function, but much less effectively. Do not
use direct water stream. May spread fire.
MEDIA TO BE AVOIDED: Do not use direct water stream.
FIRE FIGHTING INSTRUCTIONS: Keep people away. Isolate fire area and deny
unnecessary entry. Burning liquids may be moved by flushing with water to protect
personnel and minimize property damage. Burning liquids may be extinguished by dilution
with water. Do not use direct water stream. May spread fire. Fight fire from protected
location or safe distance. Consider use of unmanned hose holder or monitor nozzles. Use
water spray to cool fire exposed containers and fire affected zone until fire is out and
danger of re-ignition has passed. Immediately withdraw all personnel from area in case of
rising sound from venting safety device or discolouration of the container. Move container
from fire area if this is possible without hazard.
PROTECTIVE EQUIPMENT FOR FIRE FIGHTERS: Wear positive-pressure self-
contained breathing apparatus (SCBA) and protective fire fighting clothing (includes fire
fighting helmet, coat, pants, boots and gloves). If protective equipment is not available or
not used, fight fire from a protected location or safe distance.
* or (R) indicates a trademark of The Dow Chemical Company.

17
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239
6. ACCIDENTAL RELEASE MEASURES (See Section 15 for Regulatory Information)
PROTECT PEOPLE: Use appropriate safety equipment. For additional information, refer
to Section 8, Exposure Controls/ Personal Protection.
PROTECT THE ENVIRONMENT: Avoid contamination of all waterways.
CLEAN-UP: See Section 13, Disposal Consideration.
1. HANDLING AND STORAGE
SPECIAL PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: No special
handling requirements data available.
HANDLING: See Section 8, Exposure Controls/Personal Protection.
STORAGE: See Section 10, Stability and Reactivity.
2. EXPOSURE CONTROLS/PERSONAL PROTECTION
ENGINEERING CONTROLS: Provide general and/or local exhaust ventilation to control
airborne levels below the exposure guidelines.
PERSONAL PROTECTIVE EQUIPMENT
EYE/FACE PROTECTION: Use safety glasses. Safety glasses should be sufficient for
most operations; however, for misty operations wear chemical goggles.
SKIN PROTECTION: Use gloves impervious to this material.
RESPIRATORY PROTECTION: Atmospheric levels should be maintained below the
exposure guideline. When respiratory protection is required for certain operations, use an
approved air-purifying respirator. In misty atmospheres, use an approved mist respirator.
* or (R) indicates a trademark of The Dow Chemical Company.

18
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239
EXPOSURE GUIDELINES: Propylene glycol: AIHA WEEL is 50 ppm total, 10 mg/m3
aerosol only.
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE/PHYSICAL STATE: Clear yellow liquid.
ODOUR: Odourless
VAPOUR PRESSURE: 0.22 mmHg @ 20C
VAPOUR DENSITY: 2.6
BOILING POINT: 320F, 160C
SOLUBILITY IN WATER/MISCIBILITY: Complete
SPECIFIC GRAVITY OR DENSITY: 1.058 @ 25/25C
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY: Thermally stable at typical use temperatures.
CONDITIONS TO AVOID: Avoid use temperatures above 450F, 232C. Product can
degrade at elevated temperatures. Generation of gas during decomposition can cause
pressure in closed systems.
INCOMPATIBILITY WITH OTHER MATERIALS: Avoid contact with oxidizing materials.
Avoid contact with strong acids
HAZARDOUS DECOMPOSITION PRODUCTS: Hazardous decomposition products
depend upon temperature, air supply and the presence of other materials.
HAZARDOUS POLYMERIZATION: Will not occur.
11. TOXICOLOGICAL INFORMATION (See Section 3 for Potential Health Effects. For
detailed toxicological data, write or call the address or non-emergency number shown in
Section 1).
SKIN: The LD50 for skin absorption in rabbits is >10,000 mg/kg.
* or (R) indicates a trademark of The Dow Chemical Company.
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632

19
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239
SKIN: The LD50 for skin absorption in rabbits is >10,000 mg/kg.
INGESTION: The oral LD50 for rats is 20,000 - 34,000 mg/kg.
MUTAGENICITY: In vitro mutagenicity studies were negative. Animal mutagenicity
studies were negative.
12. ECOLOGICAL INFORMATION (For detailed Ecological data, write or call the address
or non-emergency number shown in Section 1.)
ENVIRONMENTAL FATE
MOVEMENT & PARTITIONING: Based largely or completely on data for major
component(s). Bioconcentration potential is low (BCF less than 100 or Log Pow less than
3). Potential for mobility in soil is very high (Koc between 0 and 50).
DEGRADATION AND PERSISTENCE: Based largely or completely on data for major
component(s). Material is readily biodegradable. Passes OECD test(s) for ready
biodegradability. Degradation is expected in the atmospheric environment within minutes
to hours.
ECOTOXICITY: Based largely or completely on data for major component(s). Material is
practically non-toxic to aquatic organisms on an acute basis (LC50/EC50 >100 mg/L in
most sensitive species).
13. DISPOSAL CONSIDERATIONS (See Section 15 for Regulatory Information)
DISPOSAL: DO NOT DUMP INTO ANY SEWERS, ON THE GROUND OR INTO ANY
BODY OF WATER. All disposal methods must be in compliance with all Federal,
State/Provincial and local laws and regulations. Regulations may vary in different
locations. Waste characterizations and compliance with applicable laws are the
responsibility solely of the waste generator. THE DOW CHEMICAL COMPANY HAS NO
CONTROL OVER THE MANAGEMENT PRACTICES OR MANUFACTURING
PROCESSES OF PARTIES HANDLING OR USING THIS MATERIAL. THE
INFORMATION PRESENTED HERE PERTAINS ONLY TO THE PRODUCT AS SHIPPED
IN ITS INTENDED CONDITION AS DESCRIBED IN MSDS SECTION 2
(Composition/Information On Ingredients).
* or (R) indicates a trademark of The Dow Chemical Company.
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239

20
FOR UNUSED & UNCONTAMINATED PRODUCT, the preferred options include sending
to a licensed, permitted: recycler, reclaimer, incinerator or other thermal destruction
device.
As a service to its customers, Dow can provide names of information resources to help
identify waste management companies and other facilities which recycle, reprocess or
manage chemicals or plastics, and that manage used drums. Telephone Dow‟s Customer
Information Center at 800-258-2436 or 989-832-1556 for further details.
1. TRANSPORT INFORMATION
DEPARTMENT OF TRANSPORTATION (D.O.T.): For D.O.T. regulatory information, if
required, consult transportation regulations, product shipping papers, or contact your Dow
representative.
CANADIAN TDG INFORMATION: For TDG regulatory information, if required, consult
transportation regulations, product shipping papers, or your Dow representative.
2. REGULATORY INFORMATION (Not meant to be all-inclusive –selected regulations
represented).
NOTICE: The information herein is presented in good faith and believed to be accurate as
of the effective date shown above. However, no warranty, express or implied is given.
Regulatory requirements are subject to change and may differ from one location to another;
it is the buyer‟s responsibility to ensure that its activities comply with federal, state or
provincial, and local laws. The following specific information is made for the purpose of
complying with numerous federal, state or provincial, and local laws and regulations. See
other sections for health and safety information.
* or (R) indicates a trademark of The Dow Chemical Company.
MATERIAL SAFETY DATA SHEET
Product: DOWFROST* HD HEAT TRANSFER FLUID, DYED
Product Code: 04632
Effective Date: 02/20/01, Date Printed: 07/10/02, MSD: 002239