Blue-White APNTU User manual

Quick Start Guide
®
APNTU
Turbidity Analyzer Panel

Congratulations on your purchase on a APNTU Turbidity
water analyzer!
The APNTU Analyzer Panel is specically designed as a ‘Turn-Key’ monitor-
ing solution for clean water applications including drinking water networks,
secondary water supply and decorative/swimming water applications.
The APNTU series o󰀨ers highly accurate, real-time measurement, display
and data-logging of Ultra-Low Turbidity utilizing proprietary smart sensor
technology, coupled with a touch screen display and data logging terminal.
Reference the below dimensional drawings for installation.
APNTU Panel Dimensions
7 inch touch screen
WR10
Turbidity Sensor
Water Outlet 3/4” ID
Drain Valve
3/8” OD
Flowmeter
Pressure Regulating Valve
A
B
CD
E
Water Inlet
1/4” OD
Dim Inch cm
A20.00” 50.8
B36.00” 91.4
C9.42” 23.9
D7.80” 19.8
E4.98” 12.6
Note: Strut spacing is 15”
centerline to centerline.

IMPORTANT
Safety instructions
PRE-INSTALLATION
Before you begin
To access the wiring terminal, open the enclosure by
loosening the four screws with the screwdriver. The
Analyzer must be powered by 100~240VAC 50/60Hz.
Communication wiring should be 20-24 AWG(American
Wire Gauge) shielded cable.
Planning
Ensure location of Analyzer complies with existing codes
and regulations. Location of mounting must be strong
enough to support weight of Analyzer and water. Analyzer
and mounts are not designed to support any other
structures, piping, or equipment.
Wiring
In the Box
• APNTU Analyzer Panel
• Pre-Mounted Struts
• Pre-mounted Flow Meter
• Turbidity Sensor
• 1/4” tubing OD
• 3/4” tubing ID
• Concrete Anchors
• Electrical Schematics
• Quick Start Guide
Tools Needed
Follow these instructions before installing your analyzer to avoid failure. Read
this guide and Instruction Manual before using.
CAUTION
The APNTU is designed to be installed and operated by qualied personnel only.
Please note that warranty coverage does not include damage due to misuse or
improper installation.
CAUTION
Always wear eye protection when using chemicals.
CAUTION
Do not exceed maximum pressure. High pressure and temperature will damage
the system.
PRESSURE
Plumbing
Incoming water supply and drainage piping should
be planned before installing the Analyzer. Additional
components may be required to connect to the provided
tubing.
Need more information. Please contact customer service with questions.
[email protected] 714-893-8529
Scan QR code to download
full Instruction Manual.
• Phillips Screwdriver
• Adjustable wrench

Installation Requirements
Power Supply: 100~240VAC 50/60Hz
Water Supply: Inlet water pressure should be from 7.25 – 30 psi (0.05-0.2MPa)
with an inlet feedwater line diameter of ¼-inch O.D. Tubing. The APNTU is pro-
vided with an inlet Rotameter and ow regulating valve for sample water inlet
ow control and limited pressure regulation. The range of inlet ow for the WR10
should be consistently maintained between 200 and 400 mL per minute.
Inlet Water: Connect the ¼-inch inlet water tubing to the quick adapter provided.
Consistent ow of 200-400mL is required.
Drainage: The WR10 outlet tube (3/4” ID Tubing) located on the bottom of the
WR10, should be connected to a discharge drain via gravity ow.
Outlet Line: Connect 3/4” ID tubing to the outlet drain. This is the sample water
outlet ow. This line must be diverted to drain.
Wall Mount Space: The APNTU analyzer panel size is roughly 20” H x 36” W
x 10” D in dimension. Please accommodate su󰀩cient space for mounting. The
panel is equipped with pre-installed rear unistrut for simple wall mounting.
Wall Mount Weight: Approximately 45 lbs (20kg). Please use appropriate
mounting hardware.
Wiring
The APNTU analyzer has universal AC power supply equipment allowing
users simply to plug the power supply into a 100~240V AC 50/60Hz power
outlet for normal operation.
The process of electrical connection to contact the 220V single-phase power
supply, should be operated by personnel with an electrician's license. Failure
to operate according to the electrical code of practice may result in electric
shock injury or even death. Note: When in doubt regarding your electrical
installation, contact a licensed electrician.

INSTALLATION
Step-By-Step
1Measure
Use the provided drawing dimensions to determine best mounting
location of panel.
Measure wall and locate mounting holes. Panels should be mounted
at an elevation to allow for easy access to control unit.
Wall Mount Weight: 45 lbs
Install Strut
Use the provided strut and hardware to mount the panel.
Strut to be mounted securely to wall using appropriate hardware.
Strut spacing is on 15” centerline.
If using provided anchor bolts, drill holes in concrete and clean
thoroughly. Located strut and mount with appropriate tools.
Check to make sure strut is secure and level.
2
4Connect Electrical and Tubing
Use provided electrical diagram to connect power and
communication wiring.
Consult with electrical profession before performing any
electrical work.
Mount Panel
Mounting panel will requires 2 or 3 persons.
Mount panel to strut using provided hardware.
Be sure panel is level before securing.
Check spacing and panel before connecting electrical and piping.
3
5Power Up System
Check all electrical connections before powering on system.
Check piping connections for leaks.
System is activated by pressing Power button on side of control panel.

Start-Up and Operation
After the system is powered on (using the power button, located on the left side
of the TS-10), a “Blue-White” introduction screen will appear and then immediate-
ly proceed to Real Time Monitoring screen.
The system does not require “User Login” to view real time monitoring of the
system. “User Login” is only necessary when changing parameter settings or
performing calibrations. To access this now, press the icon and refer to
Instruction Manual for more instructions regarding login and user management.
Real Time Monitoring
Upon start-up, the main interface screen will appear showing real-time monitoring
of the system. The data detected by the Blue-White sensor will be displayed in
real-time. For further programming instructions and a functional overview of each
section, please refer to complete Instruction Manual.
APNTU
APNTU

2
Engineering Specications
Item APNTU
Turbidity Wavelength Warm White
Light Source LED
Turbidity Dual Range 0.001 – 10 / 10 - 40.00 NTU
Turbidity Accuracy +/- 0.005 NTU or 2% <10NTU
Turbidity Repeatability +/- 0.001 NTU or 0.5% <10NTU
Measurement Accuracy 0.001 NTU or ± 1% Full Scale
Minimum Resolution 0.001 NTU
Response time 4s after immersion - Turbidity
Compliance EPA-180.1
Measurement Interval Continuous Measurement
Display 7-inch LCD Color Industrial Capacitive Touch Screen
Storage Capacity Built-In 4GB of Ram for Storing up to 1-Million Data/Event Records
Power Requirement 96-260VAC / 50-60 Hz; 10A Fuse; 200 W
Output 2 x 4-20 mA / RS-485 Modbus - RTU / Modbus TCP
Input 2 x 4-20 mA / RS-485 Modbus - RTU
USB 1 x USB host, for data downloading and screen upgrade
Internet RJ-45 socket, Modbus-TCP
Panel Operational Temperature 40 – 113oF (4-45 oC)
Storage Temperature Instrument: -4 – 131oF (-20 – 55oC) / Sensors 32 – 122oF (0 – 50oC)
Sample Water Temperature 40 – 104oF (4-40oC)
Sample Water Pressure 7.25 – 30 psi (0.05 – 0.2MPa)
Installation WR10 Self-Regulating Flow Reservoir w/Rotameter & Isolation Valve - Included
WR10 Minimum Flow Rate 3.1 g/h (200 mL/minute)
WR10 Maximum Flow Rate 6.2 g/h (400 mL/minute)
WR10 Sample Inlet 1/4 - inch OD
WR10 Sample Outlet 3/4 - inch ID - To Drain
WR10 Drain 1/2 - inch NPT
Rating IP-65 Panel-Display / IP-67 Sensors
Regulation CE / RoHS
Relative Humidity 20% - 90% (No Condensation)
Altitude <6,561 feet (<2,000 Meter)
Dimensions (HxWxD) Panel 36.00 H x 20.00 W x 9.42 D inches
Approximate Product Weight 33 lbs
Shipping Dimensions 42” x 26” x 16” (1067H x 661W x 407D mm)
Engineering Specications

LIMITED WARRANTY
Your Blue-White product is a quality product and
is warranted for a specic time from the date
of purchase (proof of purchase is required).
The product will be repaired or replaced at our
discretion. Failure must have occurred due to a
defect in material or workmanship and not as a
result of the operation of the product other than
in normal operation as dened in the product
manual. Warranty status is determined by the
product’s serial label and the sales invoice or
receipt. The serial label must be on the product
and legible. The warranty status of the product
will be veried by Blue-White or a factory-
authorized service center.
APNTU is warranted for 1 year from the date of
purchase.
WHAT IS NOT COVERED
• Freight to the factory, or service center.
• Products that have been tampered with, or in
pieces.
• Damage resulting from misuse, carelessness
such as chemical spills on the enclosure,
abuse, lack of maintenance, or alteration which
is out of our control.
• Damage by faulty wiring, power surges, or acts
of nature.
• Damage that occurs as a result of:
meter misalignment, improper installation, over
tightening, use of non-recommended
chemicals, use of non-recommended adhesives
or pipe dopes, excessive heat or pressure,
or allowing the unit to support the weight of
related piping.
BLUE-WHITE does not assume responsibility for
any loss, damage, or expense directly or indirectly
related to or arising out of the use of its products.
Failure must have occurred due to a defect in
material or workmanship and not as a result of
the operation of the product other than in normal
operation as dened in the manual.
Warranty status is determined by the product’s
serial label and the sales invoice or receipt. The
serial label must be on the product and legible.
The warranty status will be veried by Blue-White
or a factory-authorized service center.
PROCEDURE FOR IN-WARRANTY REPAIR
Warranty service must be performed by the
factory or an authorized service center. Contact
the factory or local repair center to obtain a
RMA (Return Material Authorization) number.
Decontaminate, dry, and carefully pack the
product to be repaired. Please enclose a brief
description of the problem and proof of purchase.
Prepay all shipping and insurance costs. COD
shipments will not be accepted. Damage caused
by improper packaging is the responsibility of the
sender. When In-Warranty repair is completed,
the factory pays for return shipping to the dealer
or customer.
Have Questions?
Contact us
[phone]
[email protected] blue-white.com/contact-us
P.N. #80000-188 APNTU QSG Rev. 0.9 20230102
WARRANTY
Information