Blue-White Sonic-Pro T-Track User manual

T-Track Installation Guide - V-Mount method
Sonic-Pro
d
d
Sonic-Pro
1
Parts Locator
Locate the T-Track assembly
package and your Transducer
set. The package should
contain the following items:
1) Retainer slide nut (2)
2) Positioning set screw (2)
3) Tensioning thumb screw (2)
4) T-Track cover
5) V-Block (2)
6) V-Block screws (8)
7) Pipe clamp (2)
8) Pipe clamp screws (2)
9) Pipe clamp wrench (1)
10) Installation Guide (1)
Note the serial number
location on the transducer.
8
9
7
5
4
1
6
2
3
10
2
Determine Separation
Distance
If not already done, configure
the meter for the pipe
application. The meter’s
display screen will display the
transducer separation
distance.
3
Install Retainer Slide
Nut Assembly
Install the Positioning Set
Screws (2) and the
Tensioning Thumb Screws
(3) into the Retainer Slide
Nuts (1).
There is a captured nut
located inside transducer
housing. While holding the
captured nut with a small
screwdriver, thread the thumb
screw into the captured nut.
Do not over-tighten.
          
2
22
3
1
                     
                     ! "
#
     $   %          & '
( ) * + * * ( ,
  -   . / 0 / 1  $   2
3
  4 5    0       6 7 8
( )
8 8
)
8 8
%     9 : ; < 5 -    -      4  =   
> ? @ A
B C D E F G H I J E C K L F M M C

5
Install and Position
the Transducers in
the T-Track
Insert the first transducer’s
Retainer Slide Nut (1)
through the square opening in
the underside of the T-Track
Cover (4). Align the grooves
in the Slide Nut with the slot
in the T-Track Cover. Slide
the transducer assembly over
to the zero position and lock
in place with the Positioning
Set Screw (2).
Insert the second transducer’s
Retainer Slide Nut (1)
through the square opening in
the underside of the T-Track
Cover (4). Align the grooves
in the Slide Nut with the slot
in the T-Track Cover. Slide
the transducer assembly over
to the correct separation
distance position (see step 2)
and lock in place with the
Positioning Set Screw (2).
4
Install the V-Blocks
Position the transducer cable
through the V-Block (5).
Install the V-Block into the T-
Track Cover (4).
Install the 4 V-Block Screws
(6).
Repeat this process for the
second V-Block.
Sonic-Pro
d
5
4
6
1
4
2

N O P Q R S T U Q V W X Y Z [ \ ] Y ] ^
_ ] ` ^ \ a a \ ^ _ b ] ` c d Y e b [ [ Y ] f Y f
g b Z [ Y ^ \ a h _ h Y ` c
V d S i T j P k Q d
N l V V l m n o Q p
DOW 111 Silicone Grease
or
Adjust the Tensioning
Thumb Screws (2) counter-
clockwise so that the
transducers are fully inside the
T-Track Cover (4) as shown.
6
Adjust the Tensioning
Thumb Screws
8
Install the
Pipe Clamps
Place the first Pipe Clamp (7)
around the pipe being careful
to position the screw where it
will be easy to tighten. Insert
the Clamp Screw (8) into the
clamp. Use the Clamp
Wrench (9) to tighten the
clamp loosely onto the pipe.
Repeat for the second pipe
clamp.
Sonic-Pro
d
An acoustic coupling material
must be placed between the
transducer and the pipe
surface at the point where the
sound waves enter the pipe.
Place a drop of DOW 111
grease or the permanent Blue
Gasket pad on the oval shape
waveguide.
7
Apply Acoustic
Coupling Material
q
r
s

t u v w x y z { | x } ~ y v 
              
ProSeries
               
d
               

 ¡ ¢ ¢ £ ¤ ¥ ¦ § ¨ ¥ ¥ © ª ¦ « ¨ ¬  ¤ § ® ¦ § ¯ ® ° § £ ¨ ± ² ³ ¬ ´ µ ¶ · ¸ ¹ ¶ º » µ
¼ ½ ¾ ¿ À Á Â Ã ¹ Ä Å ¶ ¡ Ä Å  · ¶ Æ Ç È Á Â Ã ¹ Ä Å ¶ ¹ Ä ¶ ¹ ¶ ·
É Ê Ë Ì Í Á ¥ ± Î ¨ ¥ Ï Ð Î ¤ ¨ Ä Ñ ³ ¦ ® ¨ Ò ² ° Ó ¾ Ô ® ¨ ² ³ ¥ ¤ Õ Õ ° ª ® Ï Ð Î ¤ ¨ Ä Ñ ³ ¦ ® ¨ Ò ² ° Ó Ö × Ø ÁÑ Ñ Ñ Ò Ð Î ¤ ¨ Ä Ñ ³ ¦ ® ¨ Ò ² ° Ó
9
Install the T-Track
on the Pipe
Position the T-Track on the
side of the pipe - do not install
on the top or bottom of the
pipe.
Insert the first Pipe Clamp
(7) into the slot in the V-
Block (5) and tighten. Ensure
the transducers are fully
adjusted up into the T-Track
Cover (4).
Tighten both clamps securely.
Do not over-tighten.
Insert the second Pipe
Clamp (7) into the slot in the
V-Block (5) on the other side
of the T-Track and tighten.
10
Tension the
Transducers against
the Pipe Surface
Tighten the Tensioning
Thumb Screws (3) by
turning clockwise.
Confirm that the Retainer
Slide Nuts (1) are positioned
so that the distance between
the slide nuts is equal to the
correct separation distance
per step 2.
Ù
Ú
Û
Ù
Ú
Ü Ý
Þ ß à á â á á ã ä å æ ç è á ä é à ä å ä ê ë
ìä í ß æ ä ê ë æ ç è á ä é à ä å ä ê ë
î ï ð ñ ò ï ó ô õ ö