Blue-White APFCL User manual

Quick Start Guide
®
APFCL
Free Chlorine / Turbidity Analyzer Panel

Congratulations on your purchase on a APFCL Chlorine
analyzer!
The APFCL Analyzer Panel is specically designed as a ‘Turn-Key’ monitor-
ing solution for clean water applications including drinking water networks,
secondary water supply and decorative/swimming water applications.
The APFCL series o󰀨ers highly accurate, real-time measurement, display
and data-logging of Free Chlorine, pH and Temperature utilizing proprietary
smart sensor technology, coupled with a touch screen display and data log-
ging terminal.
Reference the below dimensional drawings for installation.
APFCL Series Panel Dimensions
Dim Inch cm
A12.00” 30.5
B24.00” 61.0
C15.67” 39.8
D14.05” 35.7
E1.98” 5.0
A
TS05
WR05
FCL700
C
D
B
E
Flowmeter
Water Inlet
1/4” OD
Isolation Valve
Water Outlet 3/4” ID
Drain Valve
Note: Strut spacing is 18”
centerline to centerline.

IMPORTANT
Safety instructions
PRE-INSTALLATION
Before you begin
To access the wiring terminal, open the enclosure by
loosening the four screws with the screwdriver. The
Analyzer must be powered by 100~240VAC 50/60Hz.
Communication wiring should be 20-24 AWG(American
Wire Gauge) shielded cable.
Planning
Ensure location of Analyzer complies with existing codes
and regulations. Location of mounting must be strong
enough to support weight of Analyzer and water. Analyzer
and mounts are not designed to support any other
structures, piping, or equipment.
Wiring
In the Box
• APFCL Analyzer Panel
• Pre-Mounted Struts
• Pre-mounted Flow Meter
• Chlorine Sensor
• 1/4” tubing OD
• 3/8” tubing OD
• 3/4” tubing ID
• Concrete Anchors
• Electrical Schematics
• Quick Start Guide
Tools Needed
Follow these instructions before installing your analyzer to avoid failure. Read
this guide and Instruction Manual before using.
CAUTION
The APFCL is designed to be installed and operated by qualied personnel only.
Please note that warranty coverage does not include damage due to misuse or
improper installation.
CAUTION
Always wear eye protection when using chemicals.
CAUTION
Do not exceed maximum pressure. High pressure and temperature will damage
the system.
PRESSURE
Plumbing
Incoming water supply and drainage piping should
be planned before installing the Analyzer. Additional
components may be required to connect to the provided
tubing.
Need more information. Please contact customer service with questions.
[email protected] 714-893-8529
Scan QR code to download
full Instruction Manual.
• Phillips Screwdriver
• Adjustable wrench

Installation Requirements
Power Supply: 100~240VAC 50/60Hz
Water Supply: Inlet water pressure should be from 7.25 – 30 psi (0.05-0.2MPa)
with an inlet feedwater line diameter of ¼-inch O.D. Tubing. The APFCL is pro-
vided with an inlet Rotameter and ow regulating valve for sample water inlet
ow control and limited pressure regulation. The range of inlet ow for the WR05
should be consistently maintained between 200 and 400 mL per minute.
Inlet Water: Connect the ¼-inch inlet water tubing to the quick adapter provided.
Consistent ow of 200-400mL is required.
Drainage: The WR05 outlet tube (3/4” ID Tubing) located on the bottom of the
WR05, as well as the WR05 weir overow (3/8-inch O.D. Tubing) located on the
bottom of the WR05, should both be connected to a discharge drain via gravity
ow.
Weir Overow: Connect the ⅜-inch weir overow tubing.
Outlet Line: Connect 3/4” ID tubing to the outlet drain. This is the sample water
outlet ow. This line must be diverted to drain.
Wall Mount Space: The APFCL analyzer panel size is roughly 12” H x 24” W
x 10” D in dimension. Please accommodate su󰀩cient space for mounting. The
panel is equipped with pre-installed rear unistrut for simple wall mounting.
Wall Mount Weight: Approximately 45 lbs (20kg). Please use appropriate
mounting hardware.
Wiring
The APFCL analyzer has universal AC power supply equipment allowing
users simply to plug the power supply into a 100~240V AC 50/60Hz power
outlet for normal operation.
The process of electrical connection to contact the 220V single-phase power
supply, should be operated by personnel with an electrician's license. Failure
to operate according to the electrical code of practice may result in electric
shock injury or even death. Note: When in doubt regarding your electrical
installation, contact a licensed electrician.

INSTALLATION
Step-By-Step
1Measure
Use the provided drawing dimensions to determine best mounting
location of panel.
Measure wall and locate mounting holes. Panels should be mounted
at an elevation to allow for easy access to control unit.
Wall Mount Weight: 45 lbs
Install Strut
Use the provided strut and hardware to mount the panel.
Strut to be mounted securely to wall using appropriate hardware.
Strut spacing is on 18” centerline.
If using provided anchor bolts, drill holes in concrete and clean
thoroughly. Located strut and mount with appropriate tools.
Check to make sure strut is secure and level.
2
4Connect Electrical and Tubing
Use provided electrical diagram to connect power and
communication wiring.
Consult with electrical profession before performing any
electrical work.
Mount Panel
Mounting panel will requires 2 or 3 persons.
Mount panel to strut using provided hardware.
Be sure panel is level before securing.
Check spacing and panel before connecting electrical and piping.
3
5Power Up System
Check all electrical connections before powering on system.
Check piping connections for leaks.
System is activated when power is applied.

Start-Up and Operation
After the TS-05 is turned on, the main interface will display the chlorine residu-
al, pH value, and temperature of the solution. The green dot indicates that the
communication between the TS-05 and the probe is normal. To access other
options, press the BACK Key and refer to Instruction Manual for more informa-
tion regarding features and user management.
NOTE: The FCL Sensor has a 5 minute “Initialization period” before readings
begin.
Settings
Upon pushing the Back Key, the Settings options will appear. For further pro-
gramming instructions and a functional overview of each section, please refer to
complete Instruction Manual.
Main Key Up Key
Back Key
Enter Key
Down Key
Real Time Monitoring

2
Engineering Specications
Item APFCL
Sensor Body Material 304SS
Sensor Name FCL700
Chlorine Range 0.00-5.00 ppm, 0.00-10.0 ppm (Free or Total)
Precision +/- 0.01mg/L or 1% of the value w/pH compensation to 9.0
pH Range 0-14
pH Precision +/- 0.01 pH
Sample Operating Temperature 40 – 104 °F (4 °C – 40 °C)
Sample Inlet Pressure 7.25 – 30 psi (0.05 – 0.2MPa)
Sensor Maximum Pressure 100 psi (6.9 Bar)
Sensor Response Time T95≤60s – Free Chlorine / T95≤5s - pH
Measurement Interval Continuous
Installation WR05 Self-Regulating Flow Reservoir
w/Rotameter & Isolation Valve - Included
WR05 Minimum Flow Rate 3.1 g/h (200 mL/minute)
WR05 Maximum Flow Rate 6.2 g/h (400 mL/minute)
WR05 Sample Inlet 1/4 - inch OD
WR05 Sample Outlet 3/4 - inch ID - To Drain
WR05 Sewage Overow Outlet 3/8 - inch OD - To Drain
Panel Power Supply 110/220VAC 50/60 Hz, 0.6A
Panel Storage Temperature -4 – 158 oF (-20 – 70 oC)
Panel Operating Temperature 32 – 122 oF (-0 – 50 oC)
TS05 Display 2.8” Color 320 x 240 Resolution
Input 2 x 4-20 mA / RS-485 Modbus-RTU
Output 2 x 4-20 mA (Cl and pH)/ RS-485 Modbus-RTU / 1 x Contact Relay
Data Storage 32 M Flash
USB 1 x USB host for data downloading
Relative Humidity 5% - 95% (No Condensation)
Altitude <6,561 feet (<2,000 Meter)
Dimension (H x W x D) Panel 24.0” x 12.0” x 15.67” (610H x 305W x 398D mm)
Approximate Weight ~ 11 lbs (5 kg)
Wet Material UPVC / Polycarbonate
Rating IP-65 Panel-Display / IP-67 Sensors
Compliance EPA 334.0 / ISO 7393
Regulation CE Marked / RoHS
Typical Electrode Service Life 2 years
Electrode Warranty 6 Months
Sensor Body Warranty 13 Months
Shipping Dimensions 29” x 17” x 13” (737H x 432W x 330D mm)
Engineering Specications

LIMITED WARRANTY
Your Blue-White product is a quality product and
is warranted for a specic time from the date
of purchase (proof of purchase is required).
The product will be repaired or replaced at our
discretion. Failure must have occurred due to a
defect in material or workmanship and not as a
result of the operation of the product other than
in normal operation as dened in the product
manual. Warranty status is determined by the
product’s serial label and the sales invoice or
receipt. The serial label must be on the product
and legible. The warranty status of the product
will be veried by Blue-White or a factory-
authorized service center.
APFCL is warranted for 1 year from the date of
purchase.
WHAT IS NOT COVERED
• Freight to the factory, or service center.
• Products that have been tampered with, or in
pieces.
• Damage resulting from misuse, carelessness
such as chemical spills on the enclosure,
abuse, lack of maintenance, or alteration which
is out of our control.
• Damage by faulty wiring, power surges, or acts
of nature.
• Damage that occurs as a result of:
meter misalignment, improper installation, over
tightening, use of non-recommended
chemicals, use of non-recommended adhesives
or pipe dopes, excessive heat or pressure,
or allowing the unit to support the weight of
related piping.
BLUE-WHITE does not assume responsibility for
any loss, damage, or expense directly or indirectly
related to or arising out of the use of its products.
Failure must have occurred due to a defect in
material or workmanship and not as a result of
the operation of the product other than in normal
operation as dened in the manual.
Warranty status is determined by the product’s
serial label and the sales invoice or receipt. The
serial label must be on the product and legible.
The warranty status will be veried by Blue-White
or a factory-authorized service center.
PROCEDURE FOR IN-WARRANTY REPAIR
Warranty service must be performed by the
factory or an authorized service center. Contact
the factory or local repair center to obtain a
RMA (Return Material Authorization) number.
Decontaminate, dry, and carefully pack the
product to be repaired. Please enclose a brief
description of the problem and proof of purchase.
Prepay all shipping and insurance costs. COD
shipments will not be accepted. Damage caused
by improper packaging is the responsibility of the
sender. When In-Warranty repair is completed,
the factory pays for return shipping to the dealer
or customer.
Have Questions?
Contact us
[phone]
[email protected] blue-white.com/contact-us
P.N. #80000-187APFCL QSG Rev. 0.9 20230102
WARRANTY
Information