Blue-White SONIC-PRO MS6 User manual

Quick Start Guide
®
MS6
SONIC-PRO®Chemical Feed Flow Meter

IMPORTANT
Safety instructions
PRE-INSTALLATION
Before you begin
To access the wiring terminal, open the enclosure by
removing the four screws with the provided 3/16” hex
key. The meter must be powered by 5 volts DC. Wattage
must not exceed 5 watts. 20-24 AWG(American Wire
Guage) shielded cable is recommended for signal output
connections.
The MS6 wiring compartment is equipped with two
communications cable liquid-tight cable glad grommets for
cable diameters from .190 to .205 inches. Refer to page 21,
section 11 of the provided Operating Manual for details.
Planning
Mounts and supports must be sturdy enough to support the
plumbing and prevent vibration. Vibration and heavy loads
will damage the meter.
Wiring
In the Box
• MS6 Chemical feed ow meter
• Meter Body Connection Fittings
• 3/16” Hex Key
• Flash Drive(Operating Manual
and Blue-Central®)
• USB-A to USB-C Connector
• Power Supply(User congurable)
• Quick Start Guide
Tools Needed
1/32” Mesh strainer
Follow these instructions before installing your ow meter to avoid failure.
CAUTION
The MS6 is designed to be installed and operated by qualied personnel only.
Please note that warranty coverage does not inlcude damage due to misuse or
improper installation.
CAUTION
Always wear eye protection when installing or removing ow meters.
CAUTION
Conrm chemicals being used with MS6 ow meter are compatible with wetted
components of the ow meter.
CAUTION
Do not exceed maximum pressure. High pressure and temperature will damage
the meter.
PRESSURE
Maintenance
When the MS6 Flow meter is removed from the system
or an empty pipe condition causes the meter to dry out,
always ush the meter with water before reinstalling.

INSTALLATION
Step-By-Step
1Install Blue-Central®
Blue-Central® is Blue-White’s proprietary software application
that allows the user to update rmware and view the meter’s
device details. To congure the MS6, Blue-Central® must be
installed and running on a desktop or laptop computer. Insert
the provided USB Flash Drive, and open the .exe le to
install and run the Blue-Central® application.
Connect
Connect the meter to the desktop or laptop computer with the
provided USB to USB-C cable. The meter will appear on the
Blue-Central® dashboard (may take upto 30 seconds).
2
®
4Install in an upward direction
The ow meter must be installed in a vertical plane with uid
owing in an upward direction to ensure accuracy. To reduce
large particles and bubbles that can reduce signal quality, it is
recommended that a 1/32” mesh strainer is installed at the inlet
of the meter. Ensure all o-rings are in place and properly seated.
®
Congure
It is suggested that the user congures its operating
parameter in advance. The meter will work without performing
a conguaration, however, the default settings may not be
adequate for the required application. For assistance in
conguring the meter, refer to the provided Operating Manual
(page 7, section 6.0) located on the USB.
3
Digital drawdown
5Calibrate
After installation, and the MS-6 can be calibrated and ne-
tuned to provide the best accuracy for your dosing rate.
With solution running through the owmeter, re-connect
to the computer with Blue-Central®, and perform a Digital
Drawdown. Follow directions in Section 9.0 of the Operating
Manual for best results.

LIMITED WARRANTY
Your Blue-White product is a quality product and
is warranted for a specic time from the date
of purchase (proof of purchase is required).
The product will be repaired or replaced at our
discretion. Failure must have occurred due to a
defect in material or workmanship and not as a
result of the operation of the product other than
in normal operation as dened in the product
manual. Warranty status is determined by the
product’s serial label and the sales invoice or
receipt. The serial label must be on the product
and legible. The warranty status of the product
will be veried by Blue-White or a factory-
authorized service center.
MS6 are warranted for 5 years from the date of
purchase.
WHAT IS NOT COVERED
• Freight to the factory, or service center.
• Products that have been tampered with, or in
pieces.
• Damage resulting from misuse, carelessness
such as chemical spills on the enclosure,
abuse, lack of maintenance, or alteration which
is out of our control.
• Damage by faulty wiring, power surges, or acts
of nature.
• Damage that occurs as a result of:
meter misalignment, improper installation, over
tightening, use of non-recommended
chemicals, use of non-recommended adhesives
or pipe dopes, excessive heat or pressure,
or allowing the meter to support the weight of
related piping.
BLUE-WHITE does not assume responsibility for
any loss, damage, or expense directly or indirectly
related to or arising out of the use of its products.
Failure must have occurred due to a defect in
material or workmanship and not as a result of
the operation of the product other than in normal
operation as dened in the manual.
Warranty status is determined by the product’s
serial label and the sales invoice or receipt. The
serial label must be on the product and legible.
The warranty status will be veried by Blue-White
or a factory-authorized service center.
PROCEDURE FOR IN-WARRANTY REPAIR
Warranty service must be performed by the
factory or an authorized service center. Contact
the factory or local repair center to obtain a
RMA (Return MaterialAuthorization) number.
It is recommended to include a foot strainer
and injection/check valve tting since these
devices may be clogged and part of the problem.
Decontaminate, dry, and carefully pack the
product to be repaired. Please enclose a brief
description of the problem and proof of purchase.
Prepay all shipping and insurance costs. COD
shipments will not be accepted. Damage caused
by improper packaging is the responsibility of the
sender. When In-Warranty repair is completed,
the factory pays for return shipping to the dealer
or customer.
Have Questions?
Contact us
[phone]
[email protected] blue-white.com/contact-us
P.N. #80000-602 MS6 QSG REV 10 20220725
WARRANTY
Information