Blue-White ProSeries-M MS-6 Series User manual

Quickstart Guide
The MS-6 Chemical Feed Flowmeter is shipped with the following
contents:
!MS-6 Chemical Feed Flowmeter
!Meter Body Connection Fittings
!3/16” Hex Key
®
!Flash Drive (Operating Manual and Blue-Central )
!USB-A to USB-C connector
!Power Supply (user configurable)
The MS-6 was designed to be installed and operated by qualified
personnel only. Do not attempt to install or operate the meter if you are
unsure. Seek qualified assistance. Please note that warranty coverage
does not include damage due to misuse or improper installation.
STEP 1 Unpacking
®
STEP 2 Install Blue-Central
®
To configure the MS-6, Blue-Central must be installed and running on a
®
desktop or laptop computer. Blue-Central is Blue-White’s proprietary
®
software application. To install Blue-Central , power on the desktop or
laptop computer and insert the provided USB Flash Drive. Doubleclick
® ®
the .exe file to install and run the Blue-Central Application. Blue-Central 
allows the user to update firmware as well as view the meter’s device
details.
Note: The provided USB Flash Drive also contains the MS-6 Operating
Manual.
Connect the meter to the desktop or laptop computer with the provided
®
USB to USB-C cable. The meter will appear on the Blue-Central
dashboard. The meter will appear on the dashboard (it could take up to
30 seconds).
Note: A power supply is not needed to configure the meter.
®
Note: Installing Blue-Central will add a shortcut to the desktop screen.
STEP 3 Connect
STEP 4 Configure
It is suggested that prior to mounting the MS-6
Chemical Feed meter the user configures its
operating parameters. The meter will work
without performing a configuration, however the
default settings may not be adequate for the
required application. For assistance in
configuring the meter, refer to the provided
Operating Manual (page 7, section 6.0) located
on the Flash Drive.
Fault & Warnings Relay Output Frequency Output 4-20 mA Output Pulse Output
Blue-White’s MS6 Series Setup
Sodium Hypochlorite 12.5%
Name
Chemical Profile
Blue-White’s MS6 Series
Blue-Central
General
DASHBOARD
SETTINGS
ABOUT
i
Blue-White®
Blue-Central®
Setup and Configure
Dashboard
Industries, Ltd.
Cancel x
Save
Response Sensitivity
Responsive Stable
8 seconds
®
MS-6 Chemical Feed Flowmeter

To access the wiring terminal, open the enclosure by removing the four
screws with the provided 3/16” hex key. The meter must be powered by
5 volts DC. Wattage must not exceed 5 watts. 20-24 AWG (American
wire gauge) shielded cable is recommended for signal output
connections. The MS-6 wiring compartment is equipped with two
communications cable liquid-tight cable gland grommets for cable
diameters from .190 to .205 inches.
Note: The blank grommet plug should be used when the communications
cable grommet is not required.
Refer to page 21, section 11 of the provided Operating Manual for further
details.
STEP 5 Wiring
STEP 6 Mounting
For the MS-6 Chemical Feed Flowmeter to operate properly the pipe must be full, therefore it
must be installed in a vertical position with fluid flowing in an upward direction.
To reduce large particles and bubbles that can reduce signal quality, it is recommended that a
strainer is installed at the inlet of the meter as shown.
Installation Requirements:
1. Mounting Direction can cause inaccuracies!
Meter must be installed in a vertical plane with fluid flowing in an upward
direction to ensure accuracy.
2. Vibration and heavy loads will damage the meter!
Wall, floor and ceiling mounts and supports must be carefully aligned with
the meter body and sturdy enough to support the plumbing and prevent
vibration. Never allow the meter to support the weight of related piping.
3. High pressures and temperatures will damage the meter!
The maximum acceptable temperature and pressure is interdependent. The
maximum acceptable working pressure is dependant on the actual fluid
temperature. The maximum acceptable fluid temperature is dependant on the
actual working pressure. For more information refer to the provided Operating
Manual (see Temperature Vs. Pressure chart on page 3).
4. Strainer Recommended!
1/32” mesh strainer is recommended to be installed at the inlet of the meter.
This will keep particles from entering the meter that could cause inaccurate
readings.
3
3
1
2
2
2
Ceiling
1
Floor
Product Dimensions:
P.N. 80000-603 rev. 20190722
FLOW DIRECTION
STRAINER
3.7in
[9.4cm]
3.8in
[9.7cm]
3.9in
[9.9cm]
10.02in
[25.45cm]
3.4in
[8.6cm]
Quickstart Guide MS-6 Chemical Feed Flowmeter