blueclean AR390 User manual

2
7
6
1
89
4
3
5
D
Pump
Hose
Garden Hose Adapter
Reset
Package content:
1. Pressure Water Unit
2. Manual
3. Adjustable Spray Nozzle
4. Turbo Nozzle
5. Gun
6. Nozzle Cleaning Tool
7. High Pressure Hose
8. Garden Hose Adapter
9. Quick Connect Filter
Gun Safety Button (D)
1
2
2. Install with supplied
screws. Tools needed 1
phillips screwdriver.
3
5. a) Insert lance into the
gun by turning clockwise at
the same time.
b)Turn counterclockwise
to remove.
4. a) Remove shipping cap
from gun.
b) Screw high pressure
hose to gun.
4 5
78
6. a) Remove shipping
cap from front of pres-
sure washer.
b) Attach Quick
connect filter to front of
washer.
c) Attach garden
hose adapter to the gar-
den hose.
d) Snap garden
hose adapter and filter
together.
Trigger Gun Safety
Tab
7. Activate the lock by
holding the gun and push
the lock from left to right.
Squeeze trigger to make
sure the trigger does not
move. The safety trigger
lock should be locked at
all times when pressure
washer is not in use.
9
8. a) Plug the power cord
into a grounded 120V outlet
and press the reset button as
shown.
b) THIS MUST BE DONE
EACH TIME THE UNIT IS
PLUGGED IN AN OUTLET.
Pressure Washer Quick Guide
Assembly OperAtiOns
ar390
9. Pull trigger then turn on
power switch located on front
of the washer.
10. Spray pattern shape
and intensity can be
changed by twisting the
spray adjuster at the
end of the lance. KEEP
HANDS CLEAR OF THE
FRONT OF THE LANCE
TO PREVENT INJURY.
NOTE: Turbo nozzle is
not adjustable.
6
3. Press hose reel handle
into place until you hear a
snap.
0 (off)
I (on)
10

OperAtiOns COntinued
16. a) Wrap power cord around accessories
holder in slots provided on sides and bottom.
b) Place gun and lance into side slots.
11. a) Adjust detergent knob to desired set-
ting.
b) Switch lance from High Pressure set-
ting to Low Pressure setting by pulling nozzle
away from you.
c) Switch lance back to High Pressure by
pulling nozzle towards you for high pressure
wash and rinse.
d) The use of detergents can dramatically
reduce cleaning time and assist in the remov-
al of difficult stains. Some detergents have
been customized for pressure washer use on
specific cleaning tasks. These detergents are
approximately as thick as water. NOTE: The
use of thicker detergents, such as dish soap,
will clog the chemical injection system and
prevent the application of the detergent.
13 14
17. a) Turn off the unit
b) Turn off the water
supply. Relieve any pressure
trapped in the hose by
squeezing the trigger 2 - 3
times.
c) Separate lance from gun.
d) Rotate nozzle to the
narrow stream setting. This
opens up the fan blades.
e) Using the included tip
cleaner, or any un-folded paper
clip, insert wire into the nozzle
hole and move back and forth
until debris is dislodged.
f) Remove additional
debris by back-flushing water
through the nozzle. To do this,
place end of a garden hose
(with water running) to tip
of nozzle pushing water and
debris out the back opening of
the lance.
unit stOrAge
12. a) Pull trigger then turn off
power switch located on back of
pressure washer.
b) After turning off power,
pull trigger to relieve line pressure
before removing spray gun and
hose.
Pump
Hose
Garden Hose Adapter
13. Remove high
pressure hose from
gun and pressure
washer.
Contact Us at: Phone: [phone] • www.arnorthamerica.com • [email protected]
12
15
17
16
15. Disconnect gar-
den hose. Remove
garden hose adapter
(optional).
Adjust for detergent
concentration
11
0 (off)
I (on)
14. Roll up high
pressure hose. Lock
handle.
Pressure Washer Quick Guide (cont)ar390