BlueSpot 19532 User manual

DIAMOND CUTTING DISCS
User Manual
19532 / 19533 / 19534 / 19535 / 19536 / 19547 / 19548 / 19549

01
Thank you for purchasing a BlueSpot product, you can find further information
on our range at www.BlueSpot.uk.com. Please ensure that you are using the
product correctly and that all guidance and cautions are followed in accordance
with the instructions. Please retain these instructions for future reference.
General Information
Please make sure that you read these instructions carefully in order to avoid injury when
using the diamond cutting discs. Follow all health and safety rules and regulations. If in
doubt and available please contact a more knowledgeable source.
DO NOT use if damaged.
• ALWAYS ensure the diamond cutting discs have been checked for any damage before
use. Any damage found needs to be repaired or replaced before use to prevent damage
to property or personal injury.
• ALWAYS ensure that operators are trained in the use of diamond cutting discs and
angle grinders and understand and follow the safety requirements before mounting the disc.
• ALWAYS make sure the disc has been mounted correctly and securely. Always ensure
the instructions have been followed carefully before use.
• ALWAYS allow discs to run at operating speed for one minute before use.
• ALWAYS handle discs with care to avoid accidental damage.
• ALWAYS check maximum operating speed of the diamond cutting disc and machine.
• ALWAYS use a grinder guard covering at least one-half of the diamond cutting disc
when using an angle grinder.
• ALWAYS ensure the angle grinder is unplugged when changing the discs.
• ALWAYS wear approved ear and eye protection when using discs.
• ALWAYS wear approved hand protection when using discs.
• ALWAYS wear approved dust respirators when using discs.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip
shoes.
• Maintain the diamond cutting discs in good and clean condition for best and safest
performance.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
Safe use
• Keep children and unauthorised persons away from the work area.
• BE AWARE of where your body is positioned when using the diamond cutting disc.The
body should not be positioned in line with the flap disc.
• BE AWARE that our range of diamond cutting discs are suitable for dry cutting and not
wet cutting.
• DO NOT exceed the maximum operating speed of the diamond cutting disc.
• DO NOT exceed the maximum operating speed of the machine.
•
DO NOT force the diamond cutting discs onto a machine which does not match the bore size .
• DO NOT alter the size of the diamond cutting disc bore.
• DO NOT use mounting flanges which are damaged, unclean or warped.
• DO NOT start the machine without a guard in place.
• DO NOT excessively tighten the mounting screws.
• NEVER use the diamond cutting discs to perform a task that they were not designed for.
This can cause damage to property or cause personal injury.
• NEVER use the diamond cutting discs near flammable materials or gases.
• NEVER use the diamond cutting discs for wet grinding.
• If any of the diamond cutting discs are damaged do not use.
For additional safety information, please refer to standards found in HSG17: Safety in the
Use of Abrasive Wheels which is available online at
https://www.hse.gov.uk/pubns/books/hsg17.htm

Please make sure that you read these instructions carefully in order to avoid injury when
using the diamond cutting discs. Follow all health and safety rules and regulations. If in
doubt and available please contact a more knowledgeable source.
DO NOT use if damaged.
• ALWAYS ensure the diamond cutting discs have been checked for any damage before
use. Any damage found needs to be repaired or replaced before use to prevent damage
to property or personal injury.
• ALWAYS ensure that operators are trained in the use of diamond cutting discs and
angle grinders and understand and follow the safety requirements before mounting the disc.
• ALWAYS make sure the disc has been mounted correctly and securely. Always ensure
the instructions have been followed carefully before use.
• ALWAYS allow discs to run at operating speed for one minute before use.
• ALWAYS handle discs with care to avoid accidental damage.
• ALWAYS check maximum operating speed of the diamond cutting disc and machine.
• ALWAYS use a grinder guard covering at least one-half of the diamond cutting disc
when using an angle grinder.
• ALWAYS ensure the angle grinder is unplugged when changing the discs.
• ALWAYS wear approved ear and eye protection when using discs.
• ALWAYS wear approved hand protection when using discs.
• ALWAYS wear approved dust respirators when using discs.
• Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip
shoes.
• Maintain the diamond cutting discs in good and clean condition for best and safest
performance.
• Keep the work area clean, uncluttered and ensure there is adequate lighting.
02
How to useGeneral Information
• Keep children and unauthorised persons away from the work area.
• BE AWARE of where your body is positioned when using the diamond cutting disc.The
body should not be positioned in line with the flap disc.
• BE AWARE that our range of diamond cutting discs are suitable for dry cutting and not
wet cutting.
• DO NOT exceed the maximum operating speed of the diamond cutting disc.
• DO NOT exceed the maximum operating speed of the machine.
•
DO NOT force the diamond cutting discs onto a machine which does not match the bore size .
• DO NOT alter the size of the diamond cutting disc bore.
• DO NOT use mounting flanges which are damaged, unclean or warped.
• DO NOT start the machine without a guard in place.
• DO NOT excessively tighten the mounting screws.
• NEVER use the diamond cutting discs to perform a task that they were not designed for.
This can cause damage to property or cause personal injury.
• NEVER use the diamond cutting discs near flammable materials or gases.
• NEVER use the diamond cutting discs for wet grinding.
• If any of the diamond cutting discs are damaged do not use.
For additional safety information, please refer to standards found in HSG17: Safety in the
Use of Abrasive Wheels which is available online at
https://www.hse.gov.uk/pubns/books/hsg17.htm
BlueSpot Diamond Dry Cutting Discs
BlueSpot Diamond Dry Cutting Discs are specially designed to provide fast and accurate
dry cutting. Ideal for use with many materials including roof tiles, high-density concrete,
kerbstones, slabs, pipes and bricks. High resistance to breakage and long-lasting durability.
Suitable for all makes of angle grinders.
Introduction

Bore: 22.23mm / Segment Depth: 8mm
Maximum safe speed: 13000 RPM (80m/s)
19532
115mm (4.5")
Segmented Gold
Diamond Dry Cutting Disc
Bore: 22.23mm / Segment Depth: 8mm
Maximum safe speed: 6600 RPM (80m/s)
19534
230mm (9")
Segmented Gold
Diamond Dry Cutting Disc
Bore: 22.23mm / Segment Depth: 8mm
Maximum safe speed: 13500 RPM (80m/s)
19536
115mm (4.5")
Diamond Mortar
Raking Disc
Bore: 22.23mm / Segment Depth 5mm
Maximum safe speed: 13000 RPM (80m/s)
19548
2 PCE
115mm (4.5")
Diamond Dry
Cutting Disc
Bore: 22.23mm / Segment Depth 7mm
Maximum safe speed: 13000 RPM (80m/s)
19547
2 PCE
115mm (4.5")
Segmented
Diamond Dry Cutting Disc
Bore: 22.23mm / Segment Depth 7mm
Maximum safe speed: 6600 RPM (80m/s)
19549
2 PCE
230mm (9")
Segmented
Diamond Dry Cutting Disc
Bore: 20mm / Segment Depth 8mm
Maximum safe speed: 5100 RPM (80m/s)
19533
300mm (12")
Segmented Silver
Diamond Dry Cutting Disc
Bore: 20mm / Segment Depth 8mm
Maximum safe speed: 5100 RPM (80m/s)
19535
300mm (12")
Segmented Gold
Diamond Dry Cutting Disc
03
Introduction (continued)
All Discs - MPA Tested/EN13236

04
Operation
ALWAYS ensure that operators are trained in the use of diamond cutting discs and angle
grinders and understand and follow the safety requirements before mounting the disc.
1. Choose a suitable angle grinder.
Always ensure that you have chosen the appropriate angle grinder for the task.
2. Choose a suitable diamond cutting disc.
Always ensure that you have chosen the appropriate diamond cutting disc for the task.
Refer to the information above when determining which diamond cutting disc is best
suited to the job you want to carry out.
3. Ensure the maximum operating speeds of the machine and blade are compatible.
Always ensure you have checked and are aware of the maximum operating speeds of
the diamond cutting disc and the angle grinder and that they are compatible.
4. Mounting the diamond cutting disc.
Always ensure you follow the instructions of your chosen angle grinder when mounting
any diamond cutting disc.
5. Securing the work object.
Always ensure that the work object you are cutting is firmly secured to minimise
movement during the cutting process.
6. Cutting.
Always ensure you hold the angle grinder with a firm grip and two hands. Carefully
move the grinder across the bulk or body of your work in the direction of the handle to
avoid kickback or the disc slipping which could damage your work and cause injury.
7. Finishing cutting.
Always ensure you slowly and carefully lift the grinder from the surface of the work
when finishing any grinding task.

Storage
ALWAYS ensure the diamond cutting discs are stored out of reach of children.
Store the tool in a secure, dry place.
Disposal
ALWAYS check and adhere to national regulations when disposing of any tools that are no
longer functional and cannot be repaired.
• Contact your local waste disposal authority for information on how to correctly
dispose of tools.
Cleaning & Maintenance
Clean the diamond cutting discs with a dry cloth if needed. Make sure the diamond cutting
discs are not in use when cleaning.
05
Notes
ContactDistance to Spot Size
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and
packaging should be sorted, taken to a recycling centre and disposed of in a manner which is
compatible with the environment. When the product becomes completely unserviceable and
requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
Environmental Protection
Contact
Find out more about BlueSpot®products at www.BlueSpot.uk.com
Tel: [phone]
Email: [email protected]
Orme Business Centre,
Greenacres Road,
Oldham,
OL4 3NS