Bluewater Pro 400B-HR User manual

PRO
Water purifier
Document No 822901697 Revision BB1522
© Bluewater 2015
Complete User Manual

02
Complete User manual
Contents
INTRODUCTION...................................................................................................................................................03
About this manual ..............................................................................................................................................................03
Limited warranty ..................................................................................................................................................................03
Environment information................................................................................................................................................03
Disposal .....................................................................................................................................................................................03
Safety instructions .............................................................................................................................................................03
Safety information ............................................................................................................................................................. 04
PRODUCT OVERVIEW.................................................................................................................................... 05
Models....................................................................................................................................................................................... 05
Pro outside ............................................................................................................................................................................. 05
Pro inside..................................................................................................................................................................................07
Move the water purifier ...................................................................................................................................................07
SYSTEM OVERVIEW........................................................................................................................................ 08
System description ........................................................................................................................................................... 08
Leak protection system....................................................................................................................................................10
Low pressure protection..................................................................................................................................................10
Water production....................................................................................................................................................................11
INSTALLATION ...................................................................................................................................................... 12
Before installation................................................................................................................................................................ 12
Position Pro.............................................................................................................................................................................. 13
Affix information decal.......................................................................................................................................................13
Install clean water faucet ................................................................................................................................................14
Install feed water connection.......................................................................................................................................14
Install drain water connection......................................................................................................................................15
Connect water purifier.......................................................................................................................................................16
After installation.................................................................................................................................................................... 17
Calibration.................................................................................................................................................................................18
MAINTENANCE.....................................................................................................................................................19
Each month..............................................................................................................................................................................19
Each 4-6 months.................................................................................................................................................................20
Each year..................................................................................................................................................................................23
Other............................................................................................................................................................................................23
TECHNICAL INFORMATION..........................................................................................................................28
Technical data .......................................................................................................................................................................28
Requirements on feed water to water purifier.................................................................................................29
TROUBLESHOOTING.......................................................................................................................................30
How to solve simple problems....................................................................................................................................30

03
© Bluewater June 2015
INTRODUCTION
About this manual
This manual contains complete user instructions for the Pro. It gives you the necessary instructions to
safely install, operate, do maintenance and do troubleshooting on the device.
Original language
The original language of this instruction is English, all other languages are translations of the original
instruction.
Printing options
This manual is made to be printed as a double sided A4 or A5 booklet.
Limited warranty
Refer to www.bluewatergroup.com for more information on Limited warranty.
Environment information
80% of the the water purifier components and its packaging have a label to help you recycle and discard
it correctly. The water purifier is more efficient when it cleans water for longer periods. Example: do not fill
a glass with water. Fill a jug instead.
Disposal
At the end of the water purifier’s life, disconnect the plug from the electrical supply and cut the cable
at the point where it enters the appliance. Make sure that children do not play with the left-over cable.
Contact your local authority for information about where the water purifier can be left, or contact your
dealer.
Appliances bearing this symbol must be deposited at the designated local reception point
for the disposal of electrical and electronic equipment. This product may not be disposed
of using the normal household refuse collection processes.
Safety instructions
Before you install or operate the device, you must read the safety information. Obey the instructions
in this manual to prevent injuries or damage to the equipment. This manual contains CAUTIONS and
NOTICES that are applicable for the safe operation of the device.
A CAUTION identifies conditions that can cause injury or, damage to the
equipment. Obey the instructions and do not continue until all conditions
are accepted and engaged.
A Note identifies important information for a trouble free and optimal use of
the water purifier.

04
Complete User manual
Safety information
Install the water purifier in accordance with local regulations. If you
are not sure, contact a Bluewater dealer for aid. Bluewater has no
responsibility for installation of the water purifier.
Only use the cleaned water when the lights “Purification level II and/or III”
on the control panel are on.
This appliance can be used by children who are more than 8 years old.
It can also be used by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge, if they have been given
supervision or instruction about the use of the appliance in a safe way
and understand the hazards involved.
Children shall not play with the apliance. Cleaning and user maintenance
shall not be made by children without supervision.
Do not repair or modify parts of the water purifier. This can make it
operate incorrectly, and lead to injury and damage not covered by
warranty.
Only approved Bluewater staff can do servicing and repairs on the
water purifier. Only use original replacement cartridges and parts from
Bluewater.
The water to be cleaned must obey the requirements in “Technical
information”. Check the cleaned water when the water purifier is installed
if the water does not obey these requirements. Test the water one time
every year. If the water is not clean, tastes, or smells bad, do not drink it.
Installation must comply with applicable local plumbing codes and
regulations.
Connect the water purifier to an earthed electrical supply. Use a plug
that is easy to access after installation. Only an approved electrician
must do permanent wiring on the system. A safety switch must be
installed on the system. Incorrect installation can lead to damage, or
make the water purifier dangerous to use.
Do not use the power cord if there are visible signs of damage on it. If
the power cord is damaged, a qualified electrician must replace it in order
to prevent danger.
Do not use Pro without a filter. To do so can cause damage. When Pro is
cleaned or put in storage, the filter can be removed.
If the water purifier is disconnected from water and electricity for more than
a week, store it as described in Complete User manual “Storage”.

05
© Bluewater June 2015
PRODUCT OVERVIEW
Models
Model Capable of handling higher
TDS, including brackish inlet
water
Suitable for commercial use
without an automatic shutoff
Clean water rinse valve
suitable for environments
where extra high water quality
is required
Pro 400B-HR 
Pro 400C-HF 
Pro 400C-HR 
Pro 400BC-HR  
Pro 400CV-HR  
Pro 400BCV-HR 
Pro 600C-HF 
Pro 600CV-HR  
Pro outside
Figure 1.
CV / BCV
276
14
53
119
810
Pro outside
Pos Description Pos Description
1 Control panel 7 Feed water connection with grid filter
2 Front cover 8 Clean water rinse valve (CV-models)
3 Clean water connection 9 Air gap bracket
4 Electrical connection for faucet (optional) 10 Rinse water tube
5 Drain water hose 11 Pure water tube
6 Power cord

06
Complete User manual
Control panel
For information about combinations of lights that flashes/are on, see
“Troubleshooting”.
Figure 2.
1
2
3
4
567 8
Control panel
Pos Light/button Description
1 on/off On: The water purifier is connected to power
Off: The water purifier is not connected to power
2 filter I On: The filter must be replaced.
3 filter II On: The filter must be replaced.
4 stop Flashes/On:Something is wrong, see “Troubleshooting” on page 12.
5 calibration calibration button, various functions see “Calibration” on page 17..
6 purification level I On: Purification level I-III indicates clean water purification level.
Low level I to high level III
7 purification level II
8 purification level III
Data plate
The data plate is located on the rear side of the water purifier.
Figure 3. Data plate

07
© Bluewater June 2015
Pro inside
Figure 4.
4
2
3
1
Pro inside
Pos Description Pos Description
1 Base plate 3 Pre-filter II
2 Pre-filter I 4 Reverse osmosis membrane
Move the water purifier
Always transport the water purifier upright.
Install according to “Installation” on page 12.
Only calibrate the water purifyer if the quality of the feed water has
changed, or if the membrane was replaced.
Put the water purifier into storage if it will not be used for four months or
more, or if it is to be disconnected from the water and electricity for some
days, see “Put into storage” on page 25.
Figure 5. Move the water purifier

08
Complete User manual
SYSTEM OVERVIEW
System description
Without clean water rinse valve
Figure 6.
5
6
4
3
2
1
7
System overview
Pos Description Pos Description
1 Water purifier 5 Bracket for drain water hose
2 Power cord 6 Clean water hose
3 Feed water hose 7 Clean water faucet (optional Pro 400 series)
4 Drain water hose

09
© Bluewater June 2015
Without clean water rinse valve
Figure 7. System overview
Pos Description Pos Description
1 5
2 6
3 7
4

10
Complete User manual
Leak protection system
A sensor at the bottom of the water purifier senses water leaks. If there is a leak, the feed water supply
is stopped. The water purifier cannot be started again until the leak has been repaired.
Low pressure protection
If Pro stops because of low pressure, the cause of the low pressure must
be removed. If not, the pump can be permanently damaged.
When Pro has stopped because of a low pressure problem (feed water),
water production can be started manually by pushing the calibration
button.
Low pressure restart function
Only included in models suitable for commercial use.
The low pressure restart is a function to ensure maximum availability of water.
Pro starts automatically when it has stopped because of low pressure. It tries to start three times: after
3 minutes, after 20 minutes and after 4 hours. If the water pressure is not sufficiently high after three
tries, Pro will stop.

11
© Bluewater June 2015
Water production
Only use the cleaned water when the lights “Purification level II and III” on
the control panel are on. It can take up to 60 seconds before the water
purifier indicates good water quality.
For models suitable for commercial use the faucet could be replaced by for
example a valve or a tank.
Figure 8.
12
Water production on/off
Automatic flush
The length of the flush process varies between 5-120 seconds, depending
on how long the previous drawing of water lasted.
An automatic flush will be performed if one of the conditions below are fulfilled:
Figure 9.
1 2 3
+12 h
15 min
5-120 s
Automatic flush
Pos Description
1 Flush after drawing water. Every time after drawing water.
2 Flush when drawing water. After maximum operation time 15 minutes. (Pro 400B must be manually restarted)
3 Water purifier in standby mode. Pro is connected to water and power. Flush is performed every 12 hours,
regardless of when clean water was last produced.

12
Complete User manual
INSTALLATION
Install the water purifier in accordance with local regulations. If you
are not sure, contact a Bluewater dealer for aid. Bluewater has no
responsibility for installation of the water purifier.
Install the water purifier in a vertical position on a horizontal surface.
Make sure that hoses and cables can move freely when the water
purifier is installed.
Plumbing must be done by an approved plumber. Obey local rules for
plumbing and sanitation if you do work yourself.
Use the hose set that is supplied with the water purifier. Do not use used
hose sets again.
Before installation
Unpack Pro
Hold the rear handgrip and the plastic bag to lift Pro. To hold in other
places when Pro is lifted can cause damage to Pro.
Warning! Discard the packing material. It can cause injury to children if
they play with it.
Make sure that Pro shows no signs of damage, and that no accessories are
missing. Tell the Bluewater dealer about missing parts, damage and other
problems.
Tell the transport company immediately if Pro is damaged during transport.
Figure 10. Remove the plugs

13
© Bluewater June 2015
Position Pro
Put Pro in a vertical position on a horizontal surface below the kitchen sink.
Make sure that the surface can support Pro
Position Pro near the cold water supply, the drain and an earthed electrical supply.
• Make sure that it is easy to see the control panel.
• Make sure that the front cover can be opened to get access to the prefilters.
• Hoses and cables can go in all directions from the connection point. Make sure that nothing can crush them or
cause damage to them.
Figure 11.
AB
C
DD
D
D
Position Pro
Pos Description Pos Description
A 460 mm C 482 mm
B 190 mm D min. 20 mm
Affix information decal
The accessory box contains an adhesive sheet with information decals in various languages. Select the
required language and affix the decal at the indicated place.
Figure 12. Affix information decal

14
Complete User manual
Install clean water faucet
Figure 13.
2
4 5
6
1
3Ø 13 mm
(1/2”)
A
A
1234567
Ø 3-5 mm
(1/8”)
Install clean water faucet
Measurement Quarterturn
A The measurement A is found in the specification that comes with the clean water faucet.
Install feed water connection
The water purifier is connected to cold water (2 - 40 °C) via the feed water hose.
Figure 14.
1/2” - 3/4”
21 3
Install feed water connection

15
© Bluewater June 2015
Install drain water connection
The flushed water goes through the drain water hose to the drain water
outlet. This hose can be a maximum of four meters long. The minimum
internal diameter is 13 mm.
Without clean water rinse valve
Figure 15.
×1×2
1 2
XY
Install drain water connection
Minimum Maximum
X50 mm 500 mm
Y50 mm 500 mm
With clean water rinse valve
Figure 16. Install drain water connection with air gap

16
Complete User manual
Connect water purifier
Do not connect the clean water hose to equipment before Pro has been
flushed.
Without clean water rinse valve
19
mm
2
31
Figure 17.
230 V
50 Hz
10 A
5 6 74
19
mm
Connect water purifier
With clean water rinse valve
Figure 18. Connect water purifier with clean water rinse valve

17
© Bluewater June 2015
After installation
When Pro is installed, and after each maintenance, the following
procedures must be perfomed before operation.
Flush Pro
Do not drink the water when the water purifier flushes. It is not safe to
use.
The water purifier should always be flushed:
• when it is new and has not been used,
• when it is installed again after storage/freeze protection
• when it has been cleaned
• when the membrane has been replaced.
Figure 19.
3
1 2 3
30 s 10 min
4 5
Flush Pro
Do a check for leaks
The tubing connections must be tight!
Figure 20.
12 3
×4
Check for leaks

18
Complete User manual
Calibration
Do not drink the water that is produced when the water purifier is
calibrated. It is not safe to use.
If any of the purification level lights I-III does not go out, go through the
checkpoints under Flushing and restart the calibration.
If the purification level lights I-III does a wandering flashing light, restart the
calibration.
Calibrate (reset) the water purifyer, to achieve a starting position for the degree of purification based
specifically on your water.
Only calibrate the water purifyer if:
• it is new and has not been used before.
• the feed water quality changed (for example when the water purifyer has been moved).
• the membranes were replaced.
• the emergency stop must be reset.
21 43 5
max
10 s
10 min
6 7 8 9
Figure 21. Calibration

19
© Bluewater June 2015
MAINTENANCE
After each maintenance, all procedures in chapter “After installation” on
page 16, must be perfomed before operation.
Regular maintenance is important for correct function and long
term operation. Only educated and approved personnel can do the
maintenance.
The water quality controls the maintenance frequency. If the feed water
contains high levels of suspended solids, more frequent maintenance can
be necessary.
Each month
Do a check for leaks
The tubing connections must be tight!
Figure 22.
12 3
×4
Check for leaks
Repair leaks
41 3
5 6
min
10mm
1234567
7 8
2
Figure 23. Repair leaks

20
Complete User manual
Wipe off condensation from base plate
Figure 24. Wipe off condensation from base plate
Each 4-6 months
Descale
The descaling product is harmful. Keep it where children cannot get it.
Clean your hands when you have used it.
Frequency depending on water quality and usage!
To extend the water purifier lifetime: Descale Pro with 6 month intervals or
when the flow is decreased.
If Pro has been descaled and the filters have been replaced, but the water
flow cannot be restored, contact your Bluewater dealer.
The descale takes approximately 10 hours. Do not use the water purifier
during this time. Order the descaling product from Bluewater
21 3 54
30 s
96 87 II