Bluewater Pro Series User manual

BLUEWATER PRO
WATER PURIFIER
COMPLETE USER MANUAL
For products with serial number 220401001 and later.

4 5
Pro Complete User manual © Bluewater Group 2022
CONTENTS
INTRODUCTION 05
About this manual 05
Limited warranty 05
Environment information 05
Recycle / Disposal 05
Symbols 05
Safety instructions 06
Safety information 06
PRODUCT OVERVIEW 08
Models 08
Pro outside 08
Pro inside and replacement components 09
Control panel 09
Data plate 10
Move the water purifier 10
SYSTEM OVERVIEW 11
System description 11
Leak protection system 12
Low pressure protection 12
Water production 13
INSTALLATION 14
Unpack Pro 15
Position Pro 16
Install purified water faucet 16
Install inlet water connection 17
Install drain water connection 17
Connect the water purifier 18
Commissioning flush 19
Do a check for leaks 25
MAINTENANCE 26
Each month 27
Each 4-6 months 28
Each 6-12 months 35
Each year 36
Other 36
TECHNICAL INFORMATION 47
Technical data 47
Requirements for inlet water to water purifier 47
TROUBLESHOOTING 49
How to solve simple problems 49
Product performance 51
INTRODUCTION
About this manual
This manual contains complete instructions for the Pro. It provides the necessary instructions
to safely install, operate, maintain, and troubleshoot this device.
Original language
The original language of this instruction is English.
Printing options
This manual may be printed double sided on US Letter, A4 or A5 booklet.
Limited warranty
Refer to www.bluewatergroup.com/warranty for more information on Limited warranty.
Environment information
The water purifier is more ecient when purifying a larger amount of water at a time.
Example: Filling several one litre containers is more ecient per litre than just filling
one litre at each use.
80% of the water purifier components and packaging are labeled to help you recycle
and discard correctly.
Recycle / Disposal
Contact your Bluewater dealer before disposing of the water purifier, as it can be refurbished
and has many recyclable components. If disposing, disconnect the plug from the electrical
supply and cut the electrical cord at the point where it enters the appliance. Make sure that
children do not play with the leftover electrical cord.
For information on filter recycling or disposal, contact your Bluewater dealer.
Appliances bearing this symbol must be deposited at the designated local reception
point for the disposal of electrical and electronic equipment. This product may not be
disposed of using the normal household refuse collection processes.
Symbol
The following symbol can be found on the water purifier:
Symbol Description
The ETL Listed Mark is proof that the
device has been independently tested
and meets the applicable published
standard.

6 7
Pro Complete User manual © Bluewater Group 2022
Safety instructions
Before you install or operate the device, you must read the safety information. Obey the
instructions in this manual to prevent injuries, or damage to the equipment. This manual con-
tains CAUTIONS and NOTES that are applicable for the safe operation of the device.
A CAUTION symbol identifies conditions that can cause injury, or
damage to the equipment.
DO NOT USE Pro unless all cautionary conditions listed below have
been understood and met.
A NOTE symbol identifies important information for trouble free and optimal use of the
water purifier.
Safety information
Installation of the water purifier must comply with all applicable
local regulations and plumbing codes. Contact your Bluewater
dealer if you have questions. Bluewater, as the manufacturer, has no
responsibility for water purifier installations.
Be aware! Do not use or drink the water before “PURIFICATION
LEVEL II or LEVEL III” light turns green.
When the system has been on standby, turn on the faucet and let
the water run until "PURIFICATION LEVEL II or LEVEL III" light turns
green before using or drinking the purified water. Do not drink the
water during “PURIFICATION LEVEL I”.
This appliance can be used by children who are more than 8 years
old. It can also be used by persons with reduced physical, sensory,
or mental capabilities or lack of experience and knowledge, if they
have been given supervision or instruction about the use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Only authorized technicians, distributors, or dealers approved by
Bluewater can repair or modify parts of the water purifier. If not
performed adequately, this can make it operate incorrectly, and
lead to injury and damage not covered by warranty.
Pro is a reverse osmosis system. It contains a replaceable
membrane that is very important for eective reduction of total
dissolved solids (TDS). Replace this membrane regularly. Test the
purified water periodically using a TDS/Conductivity tester at least
one time every year to make sure that Pro performs correctly. For
options, contact your Bluewater dealer. If there is any indication
that the purified water tastes, smells bad, is cloudy, or there is a
presence of particles, do not drink.
We recommend only approved technicians, distributors or
Bluewater service personnel perform installations, servicing and
repairs on the water purifier. If not performed adequately, this can
make it operate incorrectly, and lead to injury and damage not
covered by warranty.
Only use original replacement cartridges and parts from Bluewater.
For the spare parts catalogue, see www.bluewatergroup.com. For
purchase information, contact your Bluewater dealer.
The inlet water supply must meet the requirements stated in
"REQUIREMENTS FOR INLET WATER to water purifier” pages 47-48.
Connect the water purifier to an earthed/grounded electrical
supply. Use a plug that is easy to access after installation. Only an
approved electrician must do permanent wiring on the system.
Incorrect installation can lead to damage or make the water purifier
dangerous to use.
Do not use the power cord if there are visible signs of damage on it.
If the power cord is damaged, a qualified electrician must replace it
to prevent danger.
Do not use Pro without filters. This can cause damage to the
system. The filters can be removed when Pro is cleaned or put into
storage.
If the water purifier is disconnected from water and electricity for >5 days, store it as
described in this Complete User manual. See "Put into storage" on pages 39-41.
If the water purifier is disconnected from water and electricity for >5 days, store it as
described in this Complete User manual. See "Put into storage" on pages 39-41.

8 9
Pro Complete User manual © Bluewater Group 2022
ON/OFF
FILTER IIFILTER I
STOP
PURIFICATION LEVEL
1
2
3
4
5
6 7 8
Pro inside and replacement components
Figure 2. Pro inside
Control panel
For information about combinations of lights that flashes or are on, see
"Troubleshooting" on page 49.
Figure 3. Control panel
Pos Light/button Description
1 ON/OFF On:
O:
Flashes:
The water purifier is connected to power.
The water purifier is not connected to power.
The water purifier is flushing.
2 FILTER I On: Pro 400: Replace FILTER I.
Pro 600: Replace both FILTER I and II.
3 FILTER II On: Pro 400: Replace FILTER II.
Pro 600: Replace both FILTER I and II.
4 STOP Flashes/On: Something is wrong, see "Troubleshooting"
on pages 49-50.
5 Button Various functions
6 PURIFICATION LEVEL I On:
On:
On:
Incomplete purification: DO NOT DRINK.
Medium purification: Ready to drink.
Highest purification: Ready to drink.
7 PURIFICATION LEVEL II
8PURIFICATION LEVEL III
Pos Description Part Number
1 Base plate 150706401-SP
2 FILTER I, Pro 600: Carbon Block 919240005
FILTER I, Pro 400: Sediment filter 919240002
3 FILTER II, Pro 600: Carbon Block 919240005
FILTER II, Pro 400: Carbon GAC 919240003
4 Reverse osmosis membrane
Membrane service kit, type HR
(High Rejection)
150718900-SP
Membrane service kit, type HF
(High Flow)
150718901-SP 1
2
34
PRODUCT OVERVIEW
Models
Model Capable of handling
higher TDS, including
brackish inlet water
Suitable for commercial
use without an automatic
shuto
Clean water rinse valve
suitable for environments
where extra high water
quality is required
Pro 400C-HF 
Pro 400C-HR 
Pro 400BC-HR  
Pro 400CV-HR  
Pro 400BCV-HR   
Pro 600C-HF 
Pro 600CV-HR  
Pro outside
Figure 1.
1
2 3 4 5 87 9 10 11 12
6
Pro outside
Pos Description Pos Description
1 Control panel 7 Electrical connection for faucet (optional)
2 Front cover 8 Drain water hose
3Clean water connection 9 Power cord
4Clean water tube 10 Feed water tube
5 Rinse water tube (only for CV models) 11 Grid filter
6 Air-gap bracket (only for CV models) 12 Feed water connection

10 11
Pro Complete User manual © Bluewater Group 2022
Data plate
The data plate is located on the rear side of the water purifier.
Figure 4. Data plate
Move the water purifier
Always transport the water purifier upright.
Install according to "Installation" on page 14.
Put the water purifier into storage using the preserving agent if Pro is disconnected
from the water or electricity for >5 days. See "Put into storage" on pages 41-43.
Contact your Bluewater dealer for advice before relocating Pro to another
geographical location or changing the source of the inlet water supply.
Figure 5. Move the water purifier
SYSTEM OVERVIEW
System description
1
2
3
4
5
6
7
10
11
9
8
Figure 6. System overview, an example of Pro installation
Pos Description Pos Description
1 Water purifier. 4 Drain water hose, installed with air gap.
2 Power cord. 5 Bracket for drain water hose.
3Inlet water tube. 6Purified water tube.
Pos Accessories Description
7 Standard RO faucet Approved for use with Reverse Osmosis purified
water.
8 Bluewater LED faucet LED indicates service and purified water quality
notifications.
9Bluewater Triflow faucet Provides purified water in addition to hot and cold
non purified water.
10 Storage tank Use only tanks approved for use with Reverse
Osmosis purified water.
11 Appliance Dishwasher, coee machine, ice maker,
refrigerator, etc. Appliances must be approved for
use with Reverse Osmosis purified water.
Data plate information:
–Model
–Product number
–Serial number
If you need service support, be
sure to have the following data
plate information available when
calling your Bluewater dealer:

12 13
Pro Complete User manual © Bluewater Group 2022
Leak protection system
A sensor at the bottom of the water purifier senses water leaks. If there is a leak, the inlet water
supply is stopped. The water purifier cannot be started again until the leak has been repaired.
Low pressure protection
If Pro stops because of low inlet water pressure, the cause of the
low inlet pressure must be resolved.
Low pressure restart function
Figure 7.
3-10 bar
0.3-1 MPa
43-145 psi
Low pressure restart function
The low pressure restart is a function to ensure maximum availability of inlet supply water.
If Pro has stopped due to low inlet water pressure, Pro attempts to restart automatically
and continues restart attempts every 5 minutes, for up to 10 times. If the low inlet pressure
problem is not resolved by the 10th restart attempt, Pro will stop.
Once the low inlet pressure has been resolved, Pro can be restarted manually by pressing
the Button for 3 seconds.
Water production
Be aware! Do not use or drink the water before "PURIFICATION
LEVEL II or LEVEL III" light turns green. It can take up to 60 seconds
before the water purifier indicates good water quality.
Figure 8. Water production on/o
Automatic flush
The length of the flush process varies between 5 to 120 seconds, depending on the
quantity of purified water that has been produced.
An automatic flush will be performed if one of the conditions below is met:
Figure 9. Automatic flush
Pos Description
1 Automatic flush takes place after every use.
2 Automatic flush takes place after 15 minutes of total operation time. Purified water is not
available during the 2 minute flush.
3 Automatic maintenance flush takes place every 12 hours when Pro is connected to water and
power and is in Standby mode.
12 h
15 min
2 min
1 2 3

14 15
Pro Complete User manual © Bluewater Group 2022
INSTALLATION
We recommend only approved technicians, distributors, or
Bluewater service personnel perform the installation of the water
purifier. Contact your Bluewater dealer if you have questions.
Installation of the water purifier must comply with all applicable
local plumbing codes and regulations. Plumbing must be done by
an approved plumber. Contact your Bluewater dealer if you have
questions. Bluewater, as the manufacturer, has no responsibility for
water purifier installations.
Only connect the water purifier to the cold water supply. The inlet
water must be of sucient quality and fulfil the requirements for
inlet water. See “REQUIREMENTS FOR INLET WATER to water
purifier” on pages 45-46.
Install the water purifier in a vertical position on a horizontal surface.
Make sure that hoses, tubing, and electrical cords can move freely
when the water purifier is installed.
Pro must supply purified water directly to a faucet or storage tank
designed for reverse osmosis purified water. The purified water must
not travel through any non approved pipes or faucets because this
can cause corrosion damage.
The first time Pro is connected to water and power, the INSTALLER
MUST initiate “Commissioning flush” on pages 19-24.
This 54 minute flush is a VERY IMPORTANT flush and must be
allowed to continue to completion. Keep Pro connected to power,
with the purified water faucet open for the entire time. Do not
interrupt this flush. Do not drink the water until this flush is complete.
Use the hose set that is supplied with the water purifier. Do not use used hose sets again.
Unpack Pro
Warning! Discard the packing material. It can cause injury to
children if they play with it.
80% of the water purifier components and packaging are labeled to help you
recycle and discard correctly.
Make sure that Pro shows no signs of damage and that no accessories are missing.
Contact your Bluewater dealer about missing parts, damage, and other problems.
Contact the shipping company immediately if Pro was damaged during transport.
Figure 10. Unpack Pro
1
2

16 17
Pro Complete User manual © Bluewater Group 2022
Position Pro
Put Pro in a vertical position, on a horizontal surface below the kitchen sink. Make
sure that the surface can support the water purifier.
Position Pro near the cold water supply, the drain, and an earthed/grounded electrical supply.
• Make sure that it is easy to see the Control panel.
• Make sure that the front cover can be opened to access the filters.
• Hoses, tubing, and electrical cords can go in all directions from their connection points.
Make sure that nothing can impede their free movement, or crush or damage them.
Figure 11.
18.1’’
466 mm
17.5’’
460 /
225 / 8.8’’
460 mm / 18.1’’
430 / 16.9’’
395 / 15.5’’
20 mm
0.8’’
20 mm
0.8’’
20 mm
0.8’’
Position Pro
Install purified water faucet
In certain applications, the faucet may be replaced with a shuto valve for supplying
purified water to a storage tank or appliance. Shuto valves, tubing, piping, storage
tanks and appliances must be approved for use with reverse osmosis purified water.
Install the faucet according to the manufacturer’s instructions.
Figure 12. Install purified water faucet
3/8”
Hole for
RO Faucet
Min 16 mm (3/4’’)
Max 32 mm (1 1/4’’)
Install inlet water connection
Only connect the water purifier to the cold water supply. The water
must be of sucient quality and meet the requirements
for inlet water. See “REQUIREMENTS FOR INLET WATER to water
purifier” on page 47-48.
The water purifier is connected to cold water via the inlet water tubing.
Figure 13.
3/4”
321
Install inlet water connection
Install drain water connection
Install the drain water hose with an air gap.
The flushed water goes through the drain water hose to the drain water outlet. The
drain hose length should not exceed a maximum of four meters, and the internal
diameter of the drain hose or tubing should not be reduced.
Figure 14.
1
1
2
US 2
Install drain water connection

18 19
Pro Complete User manual © Bluewater Group 2022
Stop a “Commissioning flush” must be initiated!
Before connecting Pro to any drinking water storage tanks, appliances,
or equipment, the INSTALLER MUST initiate a first time “Commissioning
flush”.
DO NOT use or drink the water until the 54 minute “Commissioning flush”
has been completed. See “Commissioning flush” on pages 19-24.
Commissioning flush
A “Commissioning flush” MUST be performed when the water purifier
is first installed, whenever a reverse osmosis membrane is replaced, or
whenever Pro has been relocated to another geographical location or a
dierent inlet water supply source is used.
This VERY IMPORTANT 54 minute “Commissioning flush” must be allowed
to continue to completion.
DO NOT interrupt this flush.
DO NOT DRINK or use the water until this flush is completed.
Pro MUST NOT be connected to any water storage tanks, appliances, or
any other drinking water equipment during this flush. All drinking water
equipment must be disconnected, except a faucet or shuto valve, until
the “Commissioning flush” is completed.
Connect the water purifier
During the initial setup, ONLY connect the water purifier to a faucet
or shuto valve. DO NOT connect the water purifier to storage tanks,
appliances, or any other drinking water equipment until after the
“Commissioning flush” procedure has been completed.
DO NOT connect the water purifier to electrical power at this time.
Figure 15. Connect the water purifier
2
3
3
US
19 mm
3/4”
1
1/2’’ OD tubing
4
56
19
mm
3/4”
ON

20 21
Pro Complete User manual © Bluewater Group 2022
Figure 17. Commissioning flush
Figure 18. Commissioning flush
“Commissioning flush” instructions, proceed with steps 1-12 as follows:
Figure 16. Commissioning flush
Start with Pro disconnected
from electrical power. Read
through steps, 2-12 before
beginning.
Turn on the purified water
faucet.
Turn on the inlet supply
water.
1 2 3
10 s
Press and hold the Control panel But-
ton while plugging Pro into an electrical
outlet. Keep the Button pressed for about
10 seconds.
Again, press and hold the Control
panel Button for 10 seconds.
Release the Button when these
lights appear.
Once step 4 is completed, you will have 1 minute to initiate step 5; if step 5 is not
initiated within 1 minute, the “Commissioning flush” setup procedure will be aborted.
Once step 5 is completed, you will have 1 minute to initiate step 6; if step 6 is not
initiated within 1 minute, the “Commissioning flush” setup procedure will be aborted.
If the Standby ON/OFF light appears, the procedure has been
aborted. If aborted, turn o the water faucet, unplug Pro from
power and start again at step 1. DO NOT use or drink the
water until the “Commissioning flush” is run to completion,
to step 12.
If the Standby ON/OFF light appears, the procedure has been
aborted. If aborted, turn o the water faucet, unplug Pro from
power and start again at step 1. DO NOT use or drink the
water until the “Commissioning flush” is run to completion,
to step 12.
Release the Button when
all lights are on.
10 s
5
4

22 23
Pro Complete User manual © Bluewater Group 2022
Figure 19. Commissioning flush
Figure 20. Commissioning flush
1 s
Press and release the Control
Panel Button.
After the button is released these
lights will appear.
Press and hold the Control panel
Button for 3 seconds.
Release the Button when these
lights appear.
Water will cycle
on and o for
54 minutes.
This light sequence indicates
the flush is running.
6 8
7
Once step 6 is completed, you will have 1 minute to initiate step 7; if step 7 is not
initiated within 1 minute, the “Commissioning flush” setup procedure will be aborted.
If the Standby ON/OFF light appears, the procedure has been
aborted. If aborted, turn o the water faucet, unplug Pro from
power and start again at step 1. DO NOT use or drink the
water until the “Commissioning flush” is run to completion,
to step 12.
3 s
54 min
DO NOT DRINK!
DO NOT UNPLUG!
Wait, the “Commissioning flush” will start and run for 54 minutes.
In case of a leak or if Pro must be left unattended, stop the flush and follow the
EMERGENCY STOP procedure and restart procedure below.
Figure 21. Commissioning flush
10 s
E
M
E
R
G
E
N
C
Y
S
T
O
P
E
M
E
R
G
E
N
C
Y
S
T
O
P
Press and hold the Control
panel Button for 10 seconds.
DO NOT use or drink the water until the flush has been restarted and completed.
To restart the 54 minute “Commissioning flush”, go back to step 1.
Turn o the faucet.Unplug Pro from power to prevent use!
When only the Standby ON/OFF light
appears, release the Button.
To STOP the “Commissioning flush”:
“COMMISSIONING FLUSH” EMERGENCY
a
c
e
d
b

24 25
Pro Complete User manual © Bluewater Group 2022
OFF
After the 54 minute flush, this
light sequence appears.
When these flashing lights
appear, turn o the faucet.
3 s
Press and hold the Control panel
Button for 3 seconds.
Drinking water equipment such as reverse osmosis approved storage tanks and
appliances can now be connected to the water purifier.
Bluewater recommends any newly connected drinking water equipment and tubing
be thoroughly rinsed with the purified water before using.
When the Standby ON/OFF light
appears, release the Button.
The “Commissioning Flush” is
complete. Proceed to steps 11 and 12.
9
10
11
12 Do a check for leaks
The hose connections must be tight! Check all hose, tubing, valve, faucet, and
drinking water equipment connections. If there are any leaks, see “Repair leaks”
on page 25.
Enjoy your BLUEWATER PRO!
One of the best water purifiers in the world!
Figure 22. Commissioning flush
Figure 23. Commissioning flush
Figure 24. Commissioning flush

26 27
Pro Complete User manual © Bluewater Group 2022
MAINTENANCE
Daily maintenance: Check indicator lights
Step Action
1
Check that only the ON/OFF light is on, and no other lights are on or flashing while
Pro is in Standby mode. If any other lights are on or flashing, see ”Troubleshooting”
on page 47-48.
Weekly maintenance: Clean the water purifier
Do not use chemicals to clean the surface. Alcohol, petrol, organic
and inorganic acids, strong basic chemicals (such as concentrated
dishwashing detergent) will cause damage to the surface.
Do not use hard, sharp, or abrasive tools to clean the water purifier.
Step Action
1Clean the outer surface with a soft, moist cloth and a weak soap solution to remove
dust, stains, and dirt.
2Dry with a soft dry cloth.
Regular maintenance
Regular maintenance is important for correct function and long
term operation. Only authorized technicians, distributors, or
dealers approved by Bluewater can perform maintenance and
repairs.
If the inlet supply water or purified water quality changes, see “
Test the water” on page 36 and contact your Bluewater dealer.
Do not drink the water when the water purifier flushes, or when
you do maintenance with chemicals. It is not safe to use.
The inlet supply water quality controls the maintenance frequency. If the
inlet supply water is of low quality, do maintenance more frequently. See
“REQUIREMENTS FOR INLET WATER to water purifier” on pages 47-48.
Frequency Action
1 month Check connections for leaks, page 25.
Wipe o condensation from the base plate, page 28.
4-6 months* Replace the filters every 4-6 months, or as indicated by the FILTER I and FILTER II
LED indicator lights, page 28.
6 months* Descale, pages 31-34.
6-12 months* Clean Inlet Grid Filter, page 35.
1 year Test the purified water every year, page 36. If the purified water is not clean, do not
drink it. Contact a Bluewater dealer.
4-6 years* Replace reverse osmosis membrane. Contact your Bluewater dealer.
*Frequency depending on inlet water quality and usage.
1234567
1 42 3 3
45
910
6 7 8
min
10mm
(1/2”)
1 min
Each month
Do a check for leaks
See"Do a check for leaks" on page 25.
If the inlet supply water or purified water quality changes, see “
Test the water” on page 34 and contact your Bluewater dealer.
Repair leaks
Figure 25. Repair leaks

28 29
Pro Complete User manual © Bluewater Group 2022
Wipe o condensation from base plate
Figure 26. Wipe o condensation from base plate
Each 4-6 months
Replace filters
We recommend only approved technicians, distributors, or
Bluewater service personnel perform servicing and repairs on the
water purifier.
Pro 400:
Replace each filter every 4-6 months or replace each filter as indicated by the
corresponding FILTER I or FILTER II light.
Pro 600:
Replace both filters at the same time every 4-6 months or replace both filters at the
same time when either FILTER I or FILTER II lights up. Both filters should always be
replaced together on Pro 600.
To order filters, contact your Bluewater dealer.
1 2 3 4
II
III
I
5
Pro400
Pro400
I
:
II
:
:
:
Pro400 III +
III +
Pro600
Pro400
Pro400
I
:
II
:
:
:
Pro400 III +
III +
Pro600
MAX
60 min
×2
×1
×2
×2
3 s
6 19
Pro400
Pro400
I
:
II
:
:
:
Pro400 III +
III +
Pro600
Pro400
Pro400
I
:
II
:
:
:
Pro400 III +
III +
Pro600
MAX
60 min
×2
×1
×2
×2
3 s
6 19
7
89 10
I
II
6
20 s

30 31
Pro Complete User manual © Bluewater Group 2022
12 13 14
15
11
16
17 18
III +
!
II
I+
!
167
19
Pro400 I
:
Pro400 II
:
:
:
Pro400 III +
III +
Pro600
2 min
Pro400 I
:
3 s
Pro400 II
:
:
:
Pro400 III +
III +
Pro600
Pro400 I
:
Pro400 II
:
:
:
Pro400 III +
III +
Pro600
2 min
Pro400 I
:
Pro400 II
:
:
:
Pro400 III +
III +
Pro600
Figure 27. Replace filter
Each 4-6 months
Descale
The descaling product can cause skin irritation. Keep the
descaling product out of the reach of children.
When handling the descaling product, wear protective gloves
and eye protection. Wash hands after using.
We recommend only approved technicians, distributors, or
Bluewater service personnel perform servicing and repairs on
the water purifier.
To order the descaling product, contact your Bluewater dealer.
Descaling frequency depends on the quality of the inlet supply water and usage!
To extend the water purifier lifetime: Descale Pro at 6 month intervals or when the
purified water flow has decreased.
If Pro has been descaled and the filters have been replaced, but the purified water
flow cannot be restored, contact your Bluewater dealer.
The descale takes approximately 10 hours. Do not use the water purifier during
this time.
1 2 3 4 5
20 s

32 33
Pro Complete User manual © Bluewater Group 2022
6
×1
3 s
MAX
60 min
619
78
9 10
×1
3 s
III
11 12
13 14 15 16
~25 °C
(77 °F)
200 g
7 oz
>3 s
17 18 19 20
21 22
45
s
10 h
23 24
25 26 27
III
28
29 30 31 32
IIII
33 35 34

34 35
Pro Complete User manual © Bluewater Group 2022
37 38 39
40 41 42
1 min
x3
3 s
3 s
3 s
36 min
>3 s
ON
43
44 45 46
Figure 28. Descale
Figure 29. Clean the Grid Filter
Each 6-12 months
Clean the Inlet Grid Filter
The Inlet Grid Filter is in the inlet water connection and catches larger particles. If the
purified water flow has decreased, if Pro becomes noisy, or if the FILTER I indicator
light comes on, the Inlet Grid Filter may be blocked.
For more information about a blocked Inlet Grid Filter, see “Troubleshooting” on
page 49-50.
Cleaning frequency depends on the quality of the inlet supply water.
1 2 3
46
5
789
1 min
36
20 s

37 © Bluewater Group 2022 36
Pro Complete User manual
Each year
Test the water
Test the purified water periodically using a TDS/Conductivity
tester at least one time every year to make sure that Pro
performs correctly. For options, contact your Bluewater dealer.
If there is any indication that the purified water tastes or smells
bad, is cloudy, or there is a presence of particles, do not drink.
See “Use disinfectant to clean the system” on page 37-40 and
contact your Bluewater dealer.
Make sure inlet supply water meets requirements. See
“REQUIREMENTS FOR INLET WATER to water purifier”
on page 47-48.
Other
Flush Pro
We recommend only approved technicians, distributors, or
Bluewater service personnel perform servicing and repairs on
the water purifier.
DO NOT drink the water during the flush process.
It is not safe to use or drink.
DO NOT interrupt this flush
The water purifier should always be flushed after the following procedures:
• When Pro has been disinfected. See “Use disinfectant to clean the system” on pages 37-40.
• When Pro has been descaled. See “Descale” on pages 31-34.
• When Pro has had the Reverse Osmosis membrane replaced. Contact your Bluewater
dealer.
• When Pro is installed again after storage/freeze protection. See “Reinstall after storage”
on pages 43-46.
• When Pro has been relocated to another geographical location or a dierent inlet water
supply source is used. See “Commissioning flush” on pages 19-24.
• When Pro is installed for the first time. See “Commissioning flush” on pages 19-24.
Use disinfectant to clean the system
Disinfectant product can be harmful. Keep the disinfectant
product out of the reach of children.
If handling the disinfectant product, wear protective gloves
and eye protection. Wash hands after using.
We recommend only approved technicians, distributors, or
Bluewater service personnel perform servicing and repairs on
the water purifier.
Use 25ml (1 oz) of a 3.5% sodium hypochlorite (NaClO) solution, as shown in the
illustration below.
Household chlorine bleach contains sodium hypochlorite in various percentages,
typically from 3 to 7.5%. Household chlorine bleach can be used in place of the
3.5% sodium hypochlorite solution if the amount of household bleach is adjusted to
meet the 3.5% NaCIO per 25ml (1 oz) dosage. For example: If the household bleach
contains 7% sodium hypochlorite, then half the amount of the household bleach
would be needed (12.5ml or 0.5 oz) to meet the dosage requirement. Contact your
Bluewater dealer for advice.
Sodium hypochlorite (NaClO) or household chlorine bleach
MUST NOT CONTAIN added color, fragrance, sudsing/
foaming agents, or surfactants. Contact your Bluewater dealer
for help finding the correct product.
Disinfect the water purifier when the water tastes or smells bad.
1 2 3 4 5
20 s

38 39
Pro Complete User manual © Bluewater Group 2022
6
×1
3 s
MAX
60 min
619
78
9 10
×1
3 s
III
11 12
13
25 ml
(NaClO
3.5%)
400 ml
~25°C
(77°F)
14 15 16
17 18 19
>3 s
20
21
45
s
22 23 24
30 min
10 h
25 26 27
III
28
29 30 31 32
IIII
33 35 34