BN Thermic TS-6 User manual
TS-6
Pre-programmed
Touch Sensitive Timer
(Fitting & Operating Instructions)
The TS-6 is a touch sensitive timer which
saves
energy and increases convenience
in and
around your premises.
MOUNTING AND INSTALLATION
Important - Please note that it is essential that
the Live In wire and switch Live Out is identified
prior to commencing installation.
Turn off mains supply for installation. Your TS-6
unit is compatible with a single gang, 25mm
deep, British Standard accessory plate. Please
ensure that the top and bottom lugs are
removed, if fitted, from metal wall boxes prior to
fitting. Ensure that there is adequate space for
wiring.
Step 1 - Place the Live wire, as per diagram
into the left hand position of the connector, the
switched Live Out wire into the second from left
position of the connector and neutral into right
hand position of connector. (See diagram 1)
Step 2 - To set time, as per timing table, use
switches one through four. Depending on
required time available from 2 minutes to 2 hours.
E.g. 10 minutes = switch one –off, switch two –
on, switch three –off, switch four–off. (See
diagram 2)
USAGE
The push button sensors are general purpose
time controls. Applications for suitable use
include lighting, heating and ventilation. The
timers can be used independently or as a master
unit when using slave trigger switches.
Diagram 1
Step 3 - Re-apply mains supply. The blue locator
ring will light up around the push button/touch
pad. Your appliance will now be switched off.
Please refer to operation section.
RATING AT 240V AC
Incandescent
16A
Fluorescent
16A
Compact Fluorescent
16A
Resistive
16A
Time Delay
2mins - 2hours
BN Thermic Ltd,
34 Stephenson Way, Three Bridges,
Crawley, RH10 1TN
Tel: +44 (0) 1293 547361
Email: sales@bnthermic.co.uk
Web: www.bnthermic.co.uk
Diagram 2
OUTDOOR INSTALLATION
The TS-6 can only be used in conjunction with the surface mount box supplied.
Take the surface mount box and remove knock out section. If required and to ensure IP66 waterproof
rating, please use a suitable M20 cable gland. Mount the surface mount box on a secure surface using
the mounting pack supplied. Place screw cover seals over the mounting screws.
Turn off mains supply before proceeding with installation - Install as per previous timer instructions -
Mount unit onto surface mount box using the fixing screws at all four corners - Place screw hole seals over left and
right screw cavities - Clip on front fascia plate - Re-instate mains supply.
OPERATION
1. Press the push button/touch pad and the red LED will light up. Your light source or appliance will now
be switched on.
2. At any time during the working of the light source or appliance, the push button/touch pad can be
pressed to reset the timing sequence to the originally set time. E.g. when the timing period is 30 minutes,
if push button/touch pad is pressed 15 minutes into the sequence, the timer will re-set for a further 30
minutes.
3. To end the timing sequence prematurely, press and hold the push button/touch pad until the red LED
flashes continuously indicating the last minute of operation. Your appliance will be switched off, after one
minute.
4. At one minute prior to the end of the timing sequence, the red LED will begin to flash continuously for
the last minute of operation. The blue locator ring will then illuminate once the appliance has gone off.
IMPORTANT NOTICE
All wiring should be carried out by a competent person or a qualified Electrician in accordance with the
current IEE Wiring Regulations. If unit is faulty return to place of purchase.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data,
specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Your BN Thermic product is guaranteed for
one year from date of purchase. We will repair or replace at
our discretion any part found to be defective. We cannot
assume any consequential liability. This guarantee in no way
prejudices your rights under common law and is offered as
an addition to consumer liability rights.
TS6INS-v01-1
Other BN Thermic Timer manuals
