BNC 588-OEM 250ps User manual

588-OEM-250ps Board Level Connection Information
588-OEM-250ps Board Level Overview
The 588-OEM-250ps is a board level option based on the 588 series pulse generator. The
specifications, communications, and overall functionality of the OEM model are the same as
described for the Model 588. The unit is available with either 4 or 8 independent outputs
that can be used for synchronizing multiple events. The 588-OEM-250ps all communications will
take place through USB, Ethernet, or RS-232 as there is no display or keypad for
interactions. The guide for standard SCIP communications with the unit can be found
above in the 588 standard manual. As with the 588, the OEM version is capable of generating
multiple pulses for all applications; but additional setup is required before even basic
pulsing may begin.
Digital Control Board Connection Information
*Note: The Power Input and Power Switch Connector are required connections for the 8530
module to function.
Power Input Connector (J2 - DC In)
The recommended connector is Molex 4 pin female C-grid (Molex #50-57-9404) or
equivalent.
The recommended contacts are Molex female terminals with gold contacts (Molex #16-
02-0087) or equivalent.
Pin Number: Connection: Specification:
1 (denoted by arrow on connector) +5 Volts DC 5V±2%, 1.2 Amp nominal capability
2 Ground
3 Ground
4 +24 Volts DC 24V±6%, 0.8A nominal capability
*Note: For an additional cost a recommended power supply and cable can be supplied
Power Switch Connector (J4 Pwr_Enab)
The recommended connector is Molex 2 pin female C-grid (Molex #50-57-9402) or
equivalent.
The recommended contacts are Molex female terminals with gold contacts (Molex #16-
02-0087) or equivalent.
*Note: This is the power enable switch; Short the contacts to turn the unit on and open them to
power down. (This connector will come shorted)
Model 588-OEM 250ps User Manual
1
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

External Clock Input (J6)
The recommended connector is a male BNC
Internal Clock Output (J15 and J16)
The recommended connector for J16 is a male BNC
The recommended connector for J15 is a Molex 2 pin female C-grid (Molex #50-57-
9402) or equivalent.
The recommended contacts for J15 are Molex female terminals with gold contacts
(Molex #16-02-0087) or equivalent.
Pin Number: Connection:
1 (denoted by arrow on connector) Clock Out
2 Ground
Output Board Connection (Mini PCB Card Edge)
This card edge must be connected to either J1 or J2 on the Output Board
Fan Output Connector (J1 Fan)
The recommended connector is Molex 4 pin female C-grid (Molex #50-57-9404) or
equivalent.
The recommended contacts are Molex female terminals with gold contacts (Molex #16-
02-0087) or equivalent.
Pin Number: Connection: Specification:
1 (denoted by arrow on connector) +5 Volts DC 5 V±2%
2 +24 Volts DC 24 V±6%
3 N/C
4 Ground
USB Communications Connector (J3 USB)
The recommended connector is a male USB Type B
Pin Number: Connection:
1 Vbus + (+5 Volts DC)
2 Data -
3 Data +
4 Ground
2
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

RS-232 Communications Connector (J5 RS-232)
The recommended connector is a male standard density D-Sub 9 pin connector
Pin Number: Connection:
1 N/C
2 Tx - Transmit
3 Rx - Receive
4 DTR - Connected to pin 6
5 Ground
6 DSR - Connected to pin 4
7 RTS - Connected to pin 8
8 CTS - Connected to pin 7
9 N/C
Ethernet Communications Connector (J7 Ethernet Module)
The recommended connector is a male RJ-45 Jack
The pin out should be 568B or AT&T 258A
Pin Number: Connection: Wire Color:
1 Tx + (Transmit Data +) Orange/White
2 Tx - (Transmit Data -) Orange
3 Rx + (Receive Data +) Green/White
4 N/C Blue
5 N/C Blue/White
6 Rx - (Receive Data -) Green
7 N/C Brown/White
8 N/C Brown
3
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

Digital Output Board Connection Information
Digital Control Board Input (J1 or J2)
The Output Board must be connected to the Digital Control Board via one of the two
surface mounted Mini Card Edge Connectors
*Note: All other connections, besides to the Digital Control Board, will be made to the Output Board
with male BNC connectors.
Connector Name: Connector Designator: Connector Function:
Gate J6 External Gate Input
Trigger J7 External Trigger Input
A J4A Channel A Output
B J5A Channel B Output
C J4B Channel C Output
D J5B Channel D Output
E (will only be present on 8 channel
models) J2A Channel E Output
F (will only be present on 8 channel
models) J3A Channel F Output
G (will only be present on 8 channel
models) J2B Channel G Output
H (will only be present on 8 channel
models) J3B Channel H Output
Mounting Information
There are 5 X 6-23 screw holes that should be used to mount the Control Board.
There are 7 X 6-32 screw holes that should be use to mount the Output Board.
*Note: Each of these mounting holes are connected to Ground
*Note: 4 of the 7 holes on the output board are use to mount the optional 4 channel expansion
board and will come with custom made M-F standoffs if the 8 channel is ordered.
4
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

4 Channel Model when Digital Board is connected to J1 on the Output Board
Figure 11: Connection Information for the 588-OEM-250ps-4C
5
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

4 Channel Model when Digital Board is connected to J2 on the Output Board
Figure 12: Connection Information for the 588-OEM-250ps-4C
6
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

8 Channel Model when Digital Board is connected to J1 on the Output Board
Figure 13: Connection Information for the 588-OEM-250ps-8C
7
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

8 Channel Model when Digital Board is connected to J1 on the Output Board
Figure 14: Connection Information for the 588-OEM-250ps-8C
8
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

9
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14

Figure 16: Mounting Information for the 588-OEM-250ps 4 Channel Expansion Board
10
Berkeley Nucleonics Corporation
[email protected] | www.berkeleynucleonics.com
2955 Kerner Blvd, San Rafael, CA 94901 | 800-234-7858
9/14