Bobrick EclipseDryer User manual

Eclipse_DTG r10-09 Page 1 of 5
EclipseDryer®
Guide
Effective 10/09
www.bobrick.com
U.S. Headquarters: BOBRICK WASHROOM EQUIPMENT, INC.
11611 Hart Street, North Hollywood, California 91605-5882, Tel: [phone], FAX: [phone]
Email: [e-mail]
Canada Headquarters: BOBRICK WASHROOM EQUIPMENT COMPANY.
45 Rolark Drive, Scarborough, Ontario M1R 3B1, Eastern: 877.423.6555, FAX: [phone], Western:
877.423.6444, FAX: [phone], Email: sup[email protected].com
International Sales: BOBRICK WASHROOM EQUIPMENT, INC.
11611 Hart Street, North Hollywood, CA 91605-5882, +1.818.764.1000, FAX: [phone]
Email: internationa[email protected]
Australia: Bobrick Washroom Equipment Pty Ltd., 1.800.353158, FAX: [phone]
Email: internationa[email protected]
Germany: 0800.79.00.456, FAX: [phone] Email: [e-mail]
United Kingdom: Bobrick Washroom Equipment Ltd., +44.0.20.8366 1771, FAX: [phone].
Email: [e-mail]
All Bobrick dryers require cleaning every 6 months to ensure
that they function effectively. Please note that failing to clean
the dryer may result in malfunction and can void the warranty.
(Refer to page 3 of the Dryer Troubleshooting and Information Guide for Routine Maintenance Instructions)

Eclipse_DTG r10-09 Page 2 of 5
EclipseDryer®
Contents Page
1. Information and Troubleshooting 3
2. Limited Warranty 4
3. Schematic Diagrams 5

Eclipse_DTG r10-09 Page 3 of 5
Warning
Risk of electric
shock
Disconnect power
supply before
removing cover
Information and Troubleshooting
for the EclipseDryer®
For complete set of Installation Instructions refer to form No. 740 748-69
http://www.bobrick.com/Bobrick/Install_Instructions.aspx
Information about the Dryer:
Durable, deep drawn steel cover with choice of white vitreous enamel or bright polished
chrome plated finish.
Product Type:
B-740 Vitreous Enamel Cover (pictured).
B-748 Chrome Plated Cover.
Electrical Characteristics:
Models B-740 (Vitreous enamel cover), B-748 (Chrome-plated cover), 115V AC, 20 Amp,
2300 Watts, 50/60Hz, Single Phase; cULus Listed.
Models B-740 (Vitreous enamel cover), B-748 (Chrome-plated cover), 208–240V AC, 9–10
Amp, 1900–2400 Watts, 50/60Hz, Single Phase; VDE Approved, CE marked, cULus Listed,
and CCC approved.
Removal of Cover
Start installation of dryer by removing cover. Loosen
single cover-locking screw located in recess in the air
inlet/outlet grille using a Phillips-head screwdriver.
To remove cover, place a hand on each side of the
cover and tip the bottom away slightly from the air
inlet/outlet grille. Lift the cover upwards to release the
top retaining bracket from the mounting base.
If a fault occurs with the dryer:
1. Check that the electrical supply is OK.
2. Check that the circuit breaker is switched on.
3. Check that sensor is not obstructed, the sensor optics can be cleaned with a cotton
swab.
Replacement Parts
740-120 Grille
740-25 Backplate
740-150 Dryer Cover (White)
748-150 Dryer Cover (Chrome)

Eclipse_DTG r10-09 Page 4 of 5
Limited Warranty
The Bobrick B-740 & B-748 EclipseDryer®and all parts (except motor brushes) are
warranted to the original owner of the installed unit for ten years from date of original
installation, against defects in factory workmanship or material under normal use and
service *.
Motor brushes shall be warranted for three years from date of installation.
This warranty is limited to repair or exchange of defective parts at the option of Bobrick
Washroom Equipment, Inc.
THIS WARRANTY DOES NOT COVER ACCIDENTAL DAMAGE, IMPROPER
HANDLING OR INSTALLATION, OR REPAIRS MADE BY UNAUTHORIZED PERSONS,
AND SPECIFICALLY EXCLUDES CLAIMS FOR INDIRECT, ACCIDENTAL OR
CONSEQUENTIAL DAMAGES TO PROPERTY. THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO
THE SAME DURATION OF THE ABOVE WARRANTY.
Some states do not allow the exclusion of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
* Normal service constitutes performing the following preventive maintenance
procedures at six-month intervals:
Remove cover and clean any lint, dust or grease from air inlet/outlet grille.
Visually inspect motor brushes to ensure remaining brush length is a minimum
of 1/2-inch (13mm).
Labor costs for preventive maintenance shall be at owner's expense.
For repair or exchange of defective part, send the part together with installation date and
serial number to Bobrick.

Eclipse_DTG r10-09 Page 5 of 5
Schematic Diagram
115V Dryer
Schematic Diagram
208-240V Dryer