Bodet BP30001 Instruction Manual

1
BODET SA
BP30001
49340 TREMENTINES
Tél: [phone]
Fax: [phone]
Réf : 607619 B
www.bodet-time.com
Indoor Melodys
Instructions for installing and use
Check the product for shipping damage on reception for any reservations to the carrier.
MELODYS

2
Index
1 - MECHANICAL INSTALLATION 2
2 - ELECTRICAL INSTALLATION 3
2.1 - Conguration Wireless DHF/Wired 3
2.2 - « Wireless DHF » mode installation 3
2.3 - « Wired mode » installation 5
3 - SETTING THE MELODIES 7
4 - TECHNICAL CHARACTERISTICS 8
When proceeding to the installation, do not forget to select the
triggering mode of the Melodys: «wireless DHF» or «wired», see page
3.
1 - MECHANICAL INSTALLATION
Ensure that power will be available
where the sounder will be installed.
To open the casing of the sounder,
unscrew the screw (3) under the
sounder and remove the cover; remove
the 2 screws (1),
Carefully remove the front panel and
disconnect the loudspeaker cable.
Secure the sounder in its location. Make
sure that the sounder is placed at against
the wall to prevent
vibration.
Imperative: the equipment must
be switched on only after xing,
programming of the DHF circuit number
and reinstalling of the front panel.
1
3
5

3
2 - ELECTRICAL INSTALLATION
2.1 - Configuration Wireless DHF/Wired
The DIP switch 2 is used to set
the wireless Melodys in
wired version.
Warning : the operation is different
according to the mode being used:
in “Wireless DHF” mode, the master
clock Sigma selects one melody
among 16 while in “Wired mode” the
master clock turns on the Melodys
which will play the last pre-selected
(in the Melodys itself) melody.
2.2 - « Wireless DHF » mode installation
In accordance with the model, 1100-
240VAC ±10% 50/60 Hz or 24 VDC,
connect the appropriate power supply
on the terminal strip (2), As the device
is a class II device, there is no earth
connection.
The cable must be attached (point 4)
in such a way as to place no stress
on the connection terminals.
For a 24V installation, verify that
the voltage does not drop below the
threshold (24V-10%). The section of the
line should be tted to its consumption
and length.
Melodys TBT 24V installation precaution: Maximum distance allowed
Wire cross-sectional area (wire diameter) 0,52 (8/10) 0,7521,52
Number of Melodys on the line
15 43 m 62 m 125 m
10 62 m 95 m 190 m
5 125 m 190 m 380 m
Important notes:
1 – The distance can be doubled by limiting the volume to 7.
2 – These distance limitations concern only one Melodys line; but it is possible to
install several lines in parallel.
DIP switch
positions
DIP2 to position
off = wired version
DIP2 to position on
= wireless version
2
4

4
Dene the address of the DHF sounder using DIP switches 5 to 8 (see table below)
and refer to the Sigma master clock manual.
DHF circuit no Dip 5 Dip 6 Dip 7 Dip 8
60 OFF OFF OFF OFF
61 OFF OFF OFF ON
62 OFF OFF ON OFF
63 OFF OFF ON ON
64 OFF ON OFF OFF
65 OFF ON OFF ON
66 OFF ON ON OFF
67 OFF ON ON ON
68 ON OFF OFF OFF
69 ON OFF OFF ON
70 ON OFF ON OFF
71 ON OFF ON ON
72 ON ON OFF OFF
73 ON ON OFF ON
74 ON ON ON OFF
75 ON ON ON ON
Beware: in DHF version the DIP switch 2 must be in
the ON position.
Reminder: several DHF sounders can be congured on the same
address; in this case, they will all have the same programming.
On rst start-up, the DHF sounder is
in INIT mode (orange DHF LED (6)
ashing).
Set the Sigma master clock to INIT
mode (see the master clock manual).
Once the receiver is initialised, the
DHF LED is red to begin with and
then green after reception of the DHF
sounder commands from the master clock.
Note: the DHF sounder commands are sent every hour and on each modication of
the programming.
To reset to INIT mode, simply press the TST key for 10 seconds.
Two LEDs indicate the functioning of the system :
- The “~” LED (A) indicates the
presence of the power supply.
- The “Ψ” LED (B) is active during
communication with the master clock.
Green, communication is OK,
Orange and fixed, the Melodys is
just within the limit of DHF range,
reception is uncertain,
Orange and flashing, the Melodys
is in INIT mode,
Red, no DHF sounder commands received.
After the product has been switched on, it waits for an execution order from the
master clock.
DIP switch
positions
6
7
B
A

5
2.3 - « Wired mode » installation
In accordance with the model, 100-
240VAC ±10% 50/60 Hz or 24 VDC,
connect the appropriate power supply on
the terminal strip (2).
As the device is a class II device,
there is no earth connection.
The cable must be attached (point 4) in
such a way as to place no stress on the
connection terminals.
In « wired mode » (dip switch 2 in the
OFF position) the power supply of the
Melodys is what controls the ringing
programmed by the master clock. The
melody selected in the Melodys is played whenever the circuit is closed by the master
clock.
If a 230V bell system has more than ve sounders, use a contactor*, see the above
illustration.
* e.g. type Merlin Gerin reference 15373.
If a 24V bell system has many sounders, verify that the voltage does not drop below
the threshold (24V-10%). The section of the line should be tted to its consumption
and length.
Melodys TBT 24V installation precaution: Maximum distance allowed
Wire cross-sectional area (wire diameter) 0,52 (8/10) 0,7521,52
Number of Melodys on the line
15 43 m 62 m 125 m
10 62 m 95 m 190 m
5 125 m 190 m 380 m
Important notes:
1 – The distance can be doubled by limiting the volume to 7.
2 – These distance limitations concern only one Melodys line; but it is possible to
install several lines in parallel.
2
4
24V DC or 100-240VAC ±10% 50/60 Hz power supply depending on
the model.
Note: all the Melodys units must be of the same model.

6
Imperative : the equipment must be switched on only after xing, and reinstalling of
the front panel.
FOperation of the sounder in « wired mode » :
The sounder is controlled by any programmer.
- The “~” LED indicates the presence
of the power supply.
When the product is switched on, the
pre-selected melody is played.
B
A

7
3 - SETTING THE MELODIES
The Melodys sounder includes 16 melodies in the standard conguration.
By default, melody number 16 is played .
To access the sounder controls,
unscrew the screw (3) under the
sounder and remove the access ap
by pulling it forwards.
The “MEL” key is used to select a
melody (from 1 to 16). This key also
allows to change the melody playing.
The “VOL” key is used to adjust the
volume from 1 to 8.
The “TST” key starts the test and stops a sounder. The volume is validated.
To adjust the volume of all the melodies at the same time:
- Press the “Vol” button for 10 sec,
- When “d5” is displayed select the volume level (from1 to 8) by pressing the “Vol”
button the appropriate number of time,
- Press “Tst” to adjust the volume for all the melodies.
Each time the melody is played, the
number of the melody is displayed (D).
The green dot (C) at the bottom right of
the readout indicates that the melody
being played is a melody contained in
the memory of the Melodys system.
The Melodys sounder support SD card and SDHC card.
An “Optional” SD Card is available to record and play other melodies (mp3 le format).
The melodies on this SD Card replace the basic melodies of the sounder. They can
be recorded directly by the user from a PC.
The SD Card must be formatted FAT
16.2 GB maximum.
The 16 pre-recorded melodies of
the Melodys can be replaced by new
MP3 les recorded on a SD card.
The digital format of the audio les
is MP3.
The names of the les on the SD
Card must be 01.mp3 to 16.mp3.
It is possible to replace totally or partially the 16 melodies.
Each melody registered on the SD card will replace the existing
melody. In case a melody is missing on the SD card the standard
melody will be executed.
The melodies recorded on the memory card have to respect copyrights. Please refer
to the current laws in your country.
9
7
8
D
C

8
4 - TECHNICAL CHARACTERISTICS
The MELODYS sounder complies with electromagnetic compatibility directive 89/336/
EEC and R&TTE directive 1999/5/EEC.
The MELODYS sounder are designed for a residential, commercial or industrial
environment.
They comply with the European standards :
EMC Directive 2004/108/EEC and Low Voltage Directive 2006/95/ EEC,
EN 60950: Safety of Information Processing Devices.
EN 301-489-3 (EMC of radio products: emission and immunity).
EN 300-220-2 (Good use of the radio spectrum).
EN 55022: Information Processing Device emission standard,
EN 55024: Information Processing Device immunity standard.
DHF norm: NF S 87-500 C (single channel, 869.525 MHz, 500 mW).
- Power supply according to model:
- 100-240VAC ±10% 50/60 Hz,
- 24 VDC ±5%.
- Dimensions : H202 x W150 x D82mm.
- Parameter backup: permanent.
- Operating temperature: 0 to +50°C.
- Protection index: IP31.
CLEANING
Use an anti-static product.
Never use alcohol, acetone or other solvents liable to damage the casing.
Warning :
When proceeding to the installation, do not forget to select the
triggering mode of the Melodys: «wireless DHF» or «wired», see
page 3.