Bodyworx CF122 User manual

HEAVY DUTY
UTILITY BENCH
Model No:
CF122
Retain this owner’s manual for future reference
Read and follow all instructions in this owner’s manual
Version A

Contents
Assembly Instructions
Contents
Before You Begin
Assembly Steps
1
2
3-4
Parts & Hardware List 5
Page 1

Before Your Begin
Assembly Instructions
Page 2
This exercise equipment is built for optimum safety. Be sure to read the entire
manual before you assemble or operate your equipment. Please note the following
safety precautions:
1. Keep children and pets away from the equipment at all times. Do not leave
children unattended in the same room with the equipment.
2. Only one person at a time should use the equipment.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms STOP the workout at once.
CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the equipment on a clear, level surface. DO NOT use the bench
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT
wear robes or other clothing that could become caught in the equipment.
7. Use the equipment only for its intended use as described in this manual.
DO NOT use attachments not recommended by the manufacturer.
8. Before using the equipment, always do stretching exercises to properly warm up.
9. Never operate the equipment if the equipment is not functioning properly.
Tools Required
Tools Required : Allen Wrentch Set / Socket Wrentch Set
Adjustable Wrentch / Crescent Wrench
Rubber Mallet / Tape Measure
ASSEMBLY REQUIRES AT LEAST TWO PERSONS
WARNING: This Product Is Rated for Home Use Olny!WARNING: This Product Is Rated for Home Use Olny!
Using this product in a commercial setting will void all warrantiesUsing this product in a commercial setting will void all warranties
and can result in serious injury or death! and can result in serious injury or death!
Note: Note: Hand tighten bolts and nuts until machine is fully assembled.

Assembly Instructions
Page 3
STEP 1
2
3
W10
11x
N10
4x
H10x2H10x2
x3
H10x16H10x16
x2
13 x2
15
1
H10x12H10x12
x2

Assembly Instructions
Page 4
STEP 2
14 x2
W10
10x
H8-3H8-3
11
7
W8
x6
8
9
4
5
12 10 15
6
13 x4
16 x2
N10
8x
x6
H10-7H10-7
x2

Assembly Instructions
Page 5
Parts & Hardware List
Part# Discription Qty Remark
1 Main Frame 1
2 Rear Base 1
3 Front Base 1
4 Back Pad Support 1
5 Seat Pad Support 1
6 Back Pad Adjust Bracket 1
7 Seat Pad Adjust Pin 1
8 Seat Pad 1
9 Back Pad 1
10 Back Pad Adjust Axle 1
11 Seat Pad Adjust Axle 1
12 Back Pad Axle 1
13 Bushing 6 Pre-assembled
14 Wheel 2
15 Handle Sleeve 2 Pre-assembled
16 F50x50mm Inner Cap 2 Pre-assembled
H8-3 M8x25 mm Hex Head Bolt 6
H10-2 M10x20 mm Hex Head Bolt 3
H10-7 M10x45 mm Hex Head Bolt 2
H10-12 M10x70 mm Hex Head Bolt 2
H10-16 M10x90 mm Hex Head Bolt 2
W8 M8 Washer 6
W10 M10 Washer 21
N10 M10 Nut 12

BODYWORX
BODYWORX
Model No: CF122
To register your warranty, please go to
www.gpisports.com.au