Borglocks BL2615MG Configuration guide

CD
Parts List,
Installation
and
General
Information
0000000
0000000
® '---------,~
®
®
(L-=----=
®
©©
~)::! :=:::J:m\\\\ml:\\\\J:mB\\\ml:l\\\\Jm\\ \\lm\1\i
t:c:• ==:ml\\\\:m:l\\\\l:m\\\\\ml:l\\\\m!\\\\lm\ \\j
FACfORY
PRE-SET CODE
.1.
BL2615MG
PARTS LIST
Please make sure you have received all the
following parts:
(1) Keypad
(2) Inside lock body
(3) Neoprene seals x 2
( 4) Spindles
-
(5) Surface lock keep
(6) Morticed lock keep
(7)Wood screws x 8
(8) Tweezers (For changing the code)
(9) Fixing bolts. 5 supplied
(10) Spare tumblers. 2 x
Coded
2 x Uncoded
(11)
Code card
(12)Hexagonal shaft x 2

SPECLAL NOTES
Before commencing installation check that all
parts are working correctly: Press the code
according
to the code card and then the knob
should turn and return easily under spring pressure.
If you intend
to change the code, you should do it
before installing the lock,
See the code change
instructions.
CHECK THE HAND OF YOUR DOOR
~ INSIDE ~
n~" ~£:::::7o c:::rc::J~ "'n
L.:l RIGHT AHND LEFT HAND U
[]'- ~CJ[J Dl::::J~ .;lJ
4.-r:;r OUTSIDE ~
Your door is right-
handed,
if viewed,
form the outside the
hinges are
on the
right.
HOW TO CHANGE YOUR CODE NUMBER
1) Remove the lock from the door.
2) Remove the 2 retaining screws from the back
of the keypad. Take EXTRA care to keep the
keypad
on a flat surface, when you are
removing the covering plate, because there are
a lot
of small components inside.
3)
You will now see that there are 5 red coloured
coded tumblers & 8 blue coloured uncoded
tumblers plus 1 clear tumbler
('C' button).
4) To change your code, push the
'C' button down
and hold it.
You can then easily remove one or
more
of your coded & uncoded tumblers, using
the tweezers supplied.
Remember, the red tumblers represent
coded digits and the blue tumblers
represent non-coded digits
5) Please note you should NEVER remove the 'C'
tumbler.
6)
Please note the different shapes of tumblers,
before reinserting them into the lock body.
Firstly there
is a difference in shape between
the coded & uncoded tumblers, illustrated
below.
And secondly when refitting the
tumblers into the lock body, they must
be fitted
facing the right way, again
see the illustration
Below. (All square cutouts must face
out~vards)
7) After you have refitted the tumblers and made
a note
of the new code, please replace the
metaI plate with the 2 screws
8)
PLEASE NOTE.With the spare tumblers
provided, you
can either increase the number
of digits in your code to 6 - 7 or reduce to 3 - 4.
Square ~ 0 Square
Square 5 cut-out-+ o o ..-cut-out
cut-out o Red Coded
-...........: Tumbler U ft
Outwards+-
Biue Non-Coded
S /
Tumbler
quare
cut-out
If you experience any problems when fitting
this lock or changing the code
please
contact the:
Dismantling the lock will invalidate your warranty
Distributed in the U.S.A. and
Canada by
Snug Cottage Hardware Inc
Marysville, MI USA
London, ON Canada
[phone]

Surface lock
keep
Assembling and Fitting
Keypad
Morticed lock keep
Surface lock keep
Inside lock
body

MAINTENANCE INSTRUCTIONS
WEEKLY
CLEAN THE SURFACE OF THE LOCK WITH MARINE GRADE CHROME
POLISHING LIQUID. SPRAY THE EXPOSED PARTS OF THE LATCH WITH
WD40 OR EQUIVALENT.
ANNUALLY
1. REMOVE THE LOCK FROM THE DOOR.
2. SPRAY THE INSIDE OF THE LOCK THOROUGHLY WITH WD40 OR
EQUIVALENT, THROUGH THE TUMBLER HOLES AT THE BACK OF
THE LOCK.
3. SPRAY ALL THE FIXING ACCESSORIES AND THE LATCH WITH
WD40 OR EQUIVALENT.
4. PUSH EACH OF THE BUTTONS AND ROTATE THE KNOB SEVERAL
TIMES TO MAKE SURE THE LOCK IS WORKING SMOOTHLY.
REMARKS
THE ABOVE MAINTENANCE PROCEDURES CAN BE CARRIED OUT
WHENEVER THE OPERATION OF THE LOCK IS STICKY.

TEMPLATE
148mm
,_
0
0
"0
Q)
...c
"'
.......
'+--
0
3
3
I
Q)
0)
"'
"0
0
ro
~
FOR LEFT HAND DOOR
I$
Q)
.......
...c
0)
·c
$ 3
3
I
0
"'
ro
I Q)
I
...c
.......
0)
c
3
3
I
0
ro
0
ctl
"0
0
17.5mm LL
130mm
148mm
,_
0
0
"0
Q) Q)
...c
0
.......
I
'+--
0 E
Q)
$i
Q) E
00
0)
0 $
"0
I
Q)
FOR RIGHT HAND DOOR
E
¢::::
E
C')
..9:2
~
Q) I
...c
I
.......
0)
c
0
-ro
"0
I
I i7.Sm:l
0 I
LL
I.
130mm
This drilling template is to suit the following models: BL2615