Bosch 2 User manual

Access Modular Controller 2
ADS‑AMC2‑2WCF | APC‑AMC2‑2WCF
en Руководство по установке

Access Modular Controller 2 Table of contents | en 3
Bosch Security Systems B.V. Руководство по установке 2022-11 | V05 |
Table of contents
1Safety 5
2Short information 7
3Introduction 8
3.1 Description 8
3.2 Product overview 10
3.2.1 Mainboard 10
3.2.2 Status display 12
3.3 System overview 13
4Installing 14
4.1 Mounting the device on a mounting rail 14
4.2 Unmounting the device from a mounting rail 15
4.3 Opening the case 16
4.4 Closing the case 17
4.5 Cabling 18
4.5.1 Conductor data for powering the controller 18
4.6 Grounding and shielding 19
4.6.1 Grounding for host interface 19
4.6.2 Grounding for extension interface 20
4.7 Connecting the power supply to the controller 21
4.8 Ethernet host interface 22
4.9 RS-485 host interface 23
4.9.1 RS-485 Two Wire Connection 24
4.9.2 RS-485 Four Wire Connection 24
4.9.3 DIP switch selector 24
4.10 RS-485 for extension modules 26
4.11 Wiegand interface for card readers 27
4.12 Connecting relay outputs 27
4.13 Connecting analog input devices 30
4.14 Tamper protection 31
5Operating 32
5.1 Configuring Ethernet interface 32
6UL requirements 33
6.1 System requirements 34
6.1.1 Computer 34
6.2 UL 294 level descriptions 34
6.3 Installation instructions 34
6.4 Extended technical specification 37
6.4.1 RS-485 extension 37
6.4.2 Power consumption 37
7Troubleshooting 38
7.1 Resetting the software 39
7.2 Resetting the device to factory default 40
8Service and repair 41
9Disposal 42
10 Technical specifications 43
11 Appendices 45
11.1 Connecting diagrams 45
11.2 Status display 48

4en | Table of contents Access Modular Controller 2
2022-11 | V05 | Руководство по установке Bosch Security Systems B.V.
11.2.1 Bootloader V00.49 48
11.2.2 Firmware until 6x.45, 37.60 49
11.2.3 Firrmware xx.61, 37.71 50
11.2.4 Firmware xx.62, 37.72 51

Access Modular Controller 2 Safety | en 5
Bosch Security Systems B.V. Руководство по установке 2022-11 | V05 |
1 Safety
!
Warning!
Read instructions
Before working with the device, read these instructions carefully. Make sure you have
understood all information described in this document.
!
Caution!
Fire hazard and risk of electric shock due to unauthorized spare parts and accessories
Unauthorized spare parts and accessories might lack grounding wires or other safety
elements. External power supplies must be installed by qualified personnel. The service
technician must use replacement parts or accessories that are specified by the manufacturer.
!
Warning!
Risk of explosion of lithium battery
The battery can explode if it is replaced incorrectly. Pay attention to the correct polarity when
inserting.
Replace only with the same battery type, as recommended by the manufacturer.
Do not overheat or expose to fire, mechanical force, or unusual high/low air pressure
conditions.
!
Warning!
Risk of physical injury due to blocked escape routes
This product may block escape routes if not installed correctly. To keep escape routes free:
- Use locks in fail-safe mode, so that doors can be released if power fails.
- Install manual override switches, such as break-glass or lever stations, to unlock doors in an
emergency.
i
Notice!
Dispose used batteries according to the battery manufacturer’s instructions, local laws and
regulations. Batteries must be disposed of separately from household waste.
i
Notice!
Device damage due to incorrect mounting
Mount this product on the matching mounting rails.
If the device falls or is damaged, check it before the installation.
i
Notice!
Considerations on local regulations
When you install the device, consider any local fire, health and safety regulations.
i
Notice!
Device damage due to electrostatic discharge
Protect the hardware from electrostatic discharge, especially when the device is open and
exposed. Always disconnect the controller from the power source before modifying the
installation. This product does not support hot plugging.

6en | Safety Access Modular Controller 2
2022-11 | V05 | Руководство по установке Bosch Security Systems B.V.
i
Notice!
Unauthorized access
If this product is installed in an unprotected environment, unauthorized people may be able
to enter.
Install the product in a location with restricted access.
This device is not suitable for use in locations where children may be present.
i
Notice!
Some features and functions described in this document depend on the firmware loaded into
the device and host software. Make sure that the controller is updated to the firmware
version provided with the host system.
This product is RoHS compliant. See Technical data for the full table of hazardous
components.

Access Modular Controller 2 Short information | en 7
Bosch Security Systems B.V. Руководство по установке 2022-11 | V05 |
2 Short information
This controller is able to control up to two Wiegand card readers.
It is designed to fully process the access logic at assigned access points. Access points
consist of doors, gates, barriers, turn stiles, revolving doors, mantraps, ID card readers, door
opening elements and sensors.
All the product versions use encrypted connections between the access modular controller
and the host system.
The controller stores all necessary information in a battery-buffered memory and in a compact
flash storage element. Even when the unit is offline, it is able to perform:
– Independent status and authorization checks on access points
– Take access decisions
– Activate and deactivate connected peripheral elements
– Detect and register all relevant events
The Access Modular Controller (AMC) is supported by the Access Professional Edition (APE),
BIS Access Engine (ACE) and the Access Management System (AMS).
For the latest information about our products, visit our online product catalog:
www.boschsecurity.com/xc/en/product-catalog/
Manufacturing dates
For product manufacturing dates, go to www.boschsecurity.com/datecodes/ and refer to the
serial number on the product label.
Remarks
This hardware is part of a security system.
Access should be granted to authorized people only.
Some states do not allow the exclusion or limitation of implied warranties, or limitation of
liability for incidental or consequential damages, hence the above limitation or exclusion might
not apply to you.
If you need further assistance or have any questions, contact:
Bosch Security Systems B.V.
Torenallee 49
5617 BA Eindhoven
Netherlands
www.boschsecurity.com
© Bosch Security Systems B.V., 2020

8en | Introduction Access Modular Controller 2
2022-11 | V05 | Руководство по установке Bosch Security Systems B.V.
3 Introduction
3.1 Description
The controller is equipped with two independent interfaces for Wiegand type readers. It is
able to control one door with one reader in each direction and up to two doors with a reader
in one direction only.
Figure3.1: Access Modular Controller
All necessary information for access verification is stored in a battery buffered on-board
memory and a Compact Flash (CF) memory card. This guarantees autonomous access
decisions and complete access registrations even if the management host system is offline.
The built in compact flash adapter provides adequate storage capability for cardholders and
events.
The electronics of the controller are completely covered by a plastic housing. The LCD (liquid
crystal display) provides all important status information.
Unsecured Area
Figure3.2: Example

Access Modular Controller 2 Introduction | en 9
Bosch Security Systems B.V. Руководство по установке 2022-11 | V05 |
The controller can communicate upstream to the host computer using one of the following
interfaces:
– Ethernet
– RS-485 multi-dropped, not supported by:
– BIS 4.9.1 and later
– AMS 4.0 and later.
The controller has four analog input devices and four relay outputs. With its analog input
devices, the controller verifies, for example, if a lock is closed or open. The relay outputs can
be used, for example, to activate lock mechanisms if access is granted, or activate the burglar
alarm system if an intrusion or system alert is detected. If the four inputs and four outputs on
the board are not enough to configure the system, up to three additional extension boards can
be connected. The extensions offer 8 or 16 additional inputs and outputs.
In the Bosch Access Host Systems, the setup procedure for a controller is made very simple
and fast by the use of door templates. Once selected, all the inputs and outputs are
predefined. These settings can be changed to choose every free contact of the controller or a
connected extension.
The product name and marking can be found on the backside of the product housing.

10 en | Introduction Access Modular Controller 2
2022-11 | V05 | Руководство по установке Bosch Security Systems B.V.
3.2 Product overview
3.2.1 Mainboard
Figure3.3: Upper circuit board with display (front)
1 DIP switch for RS-485 address and protocol selection.
2 Lithium battery for buffering of static RAM and real time clock (RTC). The battery life
is estimated at 10 years, nevertheless an error message is generated if the voltage
sinks below a preset minimum level.
NOTICE: In order to avoid an error message caused by an earlier voltage drop we
suggest to replace the battery every 8 years. Spare part: VARTA CR 2032 PCB.
3 Reset push button - reachable through the casing using a screwdriver
4 Liquid Crystal Display
5 Push button, available on top of the housing, to select different display modes
6 Jumper: Equalization of potential between different systems and earth ground
(shield)
7 Jumper: Interface selector RS-485 host connection, RS-485 two wire or RS-485 four
wire (depends on external wiring)
8 Configurable RS-485 host interface
9 Compact flash memory
10 Project-specific interface
11 Configurable 10/100 Mbit/s Ethernet host interface