Bosch AMC2 4W User manual

AMC2 4W
APC-AMC2-4W | APC-AMC2-4WCF | APC-AMC2-4WUS
en Installation manual

AMC2 4W | Installation manual | en 3
Bosch Sicherheitssysteme GmbH F.01U.024.965 | V 0.1 | 2006.03
Remarks
This hardware is part of a security system. Access shall be lim-
ited to authorized persons only.
Some states do not allow the exclusion or limitation of implied
warranties, or limitation of liability for incidental or consequen-
tial damages, so the above limitation or exclusion might not
apply to you.
Bosch Security Systems retains all rights not expressly granted.
Nothing in this license constitutes a waiver of Bosch’s rights
under the U.S. Copyright laws or any other federal or state law.
If you have any questions concerning this license, please, write
to:
Bosch Access Systems GmbH
Adenauerstr. 20 / A3
D-52146 Würselen
Germany.

4en | Table of Contents AMC2 4W | Installation manual
F.01U.024.965 | V 0.1 | 2006.03 Bosch Sicherheitssysteme GmbH
Table of Contents
1 Please read carefully7
1.1 Explanation of Used Symbols7
1.2 Internet7
1.3 We Are Interested in Your Opinion8
2 Safety Instructions9
2.1 Important Safety Notes9
2.2 FCC & ICES Information12
2.3 Safety Precautions13
2.4 Unpacking14
3 Introduction15
3.1 Description of the AMC2 4W 15
3.2 Equipment Configuration17
3.3 Performance Characteristics20
3.4 System Overview21
4 Technical Data22
5 Installing26
5.1 Mounting26
5.2 Demounting27
5.3 Opening the AMC2 4W Case28
5.4 Cabling28
5.5 Connecting Power Supply31
5.6 RS-485 Host Interface33
5.6.1 RS-485 Two Wire Connection35
5.6.2 RS-485 Four Wire Connection36
5.6.3 DIL Switch Address Selector37
5.7 RS-232 Host Interface39
5.8 Ethernet Interface41
5.9 RS-485 Extension Module Bus42
5.10 Wiegand Interface for Card Readers43
5.11 Connecting Relay Outputs44
5.12 Connecting Analog Input Devices47
5.13 Tamper Protection49
6 Operating50
6.1 Status Display of the AMC2 4W50
6.2 Configuring the Ethernet Interface52
6.3 Resetting the AMC2 4W52
7 Appendix54
7.1 Connecting Diagrams54

AMC2 4W | Installation manual Table of Contents | en 5
Bosch Sicherheitssysteme GmbH F.01U.024.965 | V 0.1 | 2006.03
7.2 Legend58
8 Index59

6en | Table of Contents AMC2 4W | Installation manual
F.01U.024.965 | V 0.1 | 2006.03 Bosch Sicherheitssysteme GmbH

AMC2 4W | Installation manual Please read carefully | en 7
Bosch Sicherheitssysteme GmbH F.01U.024.965 | V 0.1 | 2006.03
1 Please read carefully
1.1 Explanation of Used Symbols
Throughout this document, helpful tips, important notes, cau-
tions and warnings will be presented for the reader to keep in
mind. These appear different from the rest of the text as fol-
lows:
1.2 Internet
If you are interested in further information on this product or
information on other products, please, refer to our website at
http://www.bosch-security-systems.com.
CAUTION! or WARNING!
These warn the operator that damage to the program or equip-
ment might occur.
i
NOTE!
Important Notes – must be followed for successful operation
and programming. Tips and shortcuts might also be included
here.

8en | Please read carefully AMC2 4W | Installation manual
F.01U.024.965 | V 0.1 | 2006.03 Bosch Sicherheitssysteme GmbH
1.3 We Are Interested in Your Opinion
We constantly try to improve the quality of our products and
our manuals. Should you have any suggestions for improve-
ment, please, send us your comments.
Bosch Security Systems
Adenauerstr. 20 / A3
D-52146 Würselen
Germany
Tel.:+49 24 05 / 60 05-0
Fax:+49 24 05 / 60 05-29
Email:[email protected]

AMC2 4W | Installation manual Safety Instructions | en 9
Bosch Sicherheitssysteme GmbH F.01U.024.965 | V 0.1 | 2006.03
2 Safety Instructions
2.1 Important Safety Notes
1. Read, Follow, and Retain Instructions - All safety and
operating instructions must be read and followed properly
before putting the unit into operation. Retain instructions
for future reference.
2. Consider all Warnings - Adhere to all warnings on the unit
and in the operating instructions.
3. Accessories - Use only accessories recommended by the
manufacturer or those sold with the product. Accessories
not recommended by the manufacturer shall not be used,
as they may cause hazards.
4. Installation Precautions - Do not place this unit on an
unstable stand, tripod, bracket, or mount. The unit may
fall, causing serious injury to persons and damage to the
unit. Mount the unit according to the manufacturer’s
instructions.
5. Cleaning - Disconnect the unit from power before cleaning.
Follow any instructions provided with the unit. Generally,
using a damp cloth for cleaning is sufficient. Do not use liq-
uid cleaners or aerosol cleaners.
6. Service - Do not attempt to service this unit by yourself.
Opening or removing covers may expose you to dangerous
voltages or other hazards. Refer all servicing to qualified
service personnel.
7. Damage Requiring Service - Disconnect the unit from the
main AC or DC power source and refer servicing to quali-
fied service personnel under the following conditions:
•When the power supply cord or plug is damaged.
•If liquid has been spilled or an object has fallen into
the unit.
•If the unit has been exposed to water and/or inclem-
ent weather (rain, snow, etc.).
•If the unit does not operate normally, when following
the operating instructions. Adjust only those controls

10 en | Safety Instructions AMC2 4W | Installation manual
F.01U.024.965 | V 0.1 | 2006.03 Bosch Sicherheitssysteme GmbH
specified in the operating instructions. Improper
adjustment of other controls may result in damage,
and require extensive work by a qualified technician
to restore the unit to normal operation.
•If the unit has been dropped or the cabinet damaged.
•If the unit exhibits a distinct change in performance,
this indicates that service is needed.
8. Replacement Parts - When replacement parts are
required, the service technician shall use replacement
parts that are specified by the manufacturer. Unauthorized
substitutions may result in fire, electrical shock or other
hazards.
9. Safety Check - Upon completion of service or repair work
on the unit, ask the service technician to perform safety
checks to ensure that the unit operates properly
10. Power Sources - Operate the unit only from the type of
power source indicated on the label. If unsure of the type
of power supply to use, contact your dealer
•For units intended to operate from battery power,
refer to the operating instructions.
•For units intended to operate with External Power
Supplies, use only the recommended approved power
supplies.
•For units intended to operate with a limited power
source, this power source must comply with EN/UL
60950. Substitutions may damage the unit or cause
fire or shock.
•For units intended to operate at 12 VDC normal input
voltage is 12 VDC. Voltages applied to the unit’s
power input shall not exceed 15 VDC. User-supplied
wiring, from the 12 VDC power supply to the unit,
must be in compliance with electrical codes (Class 2
power levels). Do not ground the 12 VDC supply at the
terminals or at the unit’s power supply terminals.
11. Grounding - If an outside cable system is connected to the
unit, ensure that the cable system is grounded. U.S.A.
models only Section 810 of the National Electrical Code,