Bosch Rexroth ctrlX CORE X7 User manual

ctrlX CORE
X7
Controls
Operating Instructions
R911419122, Edition 01

Copyright
© Bosch Rexroth AG 2022
All rights reserved, also regarding any disposal, exploitation, reproduction, editing,
distribution, as well as in the event of applications for industrial property rights.
Liability
The specified data is intended for product description purposes only and shall not be
deemed to be a guaranteed characteristic unless expressly stipulated in the contract.
All rights are reserved with respect to the content of this documentation and the
availability of the product.
DOK-XCORE*-X7*********-IT01-EN-P
ToLu (MaKo/MePe)
f8ded54c096fa61f0a347e887f1236a2, 1, en_US

3 / 50
ctrlX CORE X7
Bosch Rexroth AG
R911419122, Edition 01
Table of contents
1 About this documentation 6
1.1 Change record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Overview on target groups and product phases. . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Related documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5 Customer feedback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Product identification and scope of delivery 8
2.1 Product identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Using safety instructions 9
3.1 Structure of the safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Explaining signal words and the safety alert symbol. . . . . . . . . . . . . . . . . . . . . 9
3.3 Symbols used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4 Explaining the signal alert symbol on the device. . . . . . . . . . . . . . . . . . . . . . . . 10
4 Intended use 10
4.1 General information on the intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5Spare parts, accessories and wear parts 11
5.1 Power connector, 24 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2 SD card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3 RJ45 cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.4 End clamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.5 Fan unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.6 Endcover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.7 License dongle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.8 Wear parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.8.1 Read-only memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.8.2 Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6Ambient conditions 12
6.1 Ambient conditions of the ctrlX CORE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
7Technical data 13
7.1 General technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7.2 Voltage supply and current consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table of contents

4 / 50
ctrlX CORE X7
Bosch Rexroth AG
R911419122, Edition 01
8 Standards 15
8.1 Standards used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8.2 CE marking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.2.1 Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.3 UL/CSA certified. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8.4 UK declaration of conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9 Interfaces 18
9.1 Interface description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.1.1 Local bus interface EtherCAT of ctrlX COREPLUS X7. . . . . . . . . . . . . 19
10 Mounting, dismounting and electric installation 23
10.1 Housing dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10.2 Installation notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
10.3 Mounting the control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10.3.1 Mounting the fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10.4 Dismounting the control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
10.4.1 Dismounting steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10.4.2 Dismounting the fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10.5 Electric installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.5.1 External power supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.5.2 Power connector XD10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.5.3 24 V voltage supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
10.5.4 Grounding
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
10.5.5 Shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
11 Commissioning 34
11.1 IT security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
11.2 Commissioning steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
11.2.1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
11.3 Safe decommissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
11.3.1 Notes on safe decommissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
12 Device description 35
12.1 ctrlX CORE control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
12.2 Status displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
12.2.1 Status display at the power connector XD10 ctrlX COREPLUS. . . . . . 37
12.2.2 Status display of device status LED . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5 / 50
ctrlX CORE X7
Bosch Rexroth AG
R911419122, Edition 01
12.3 Initial firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
12.4 Booting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12.4.1 Secure Boot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12.5 Backing up remanent data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12.6 Real-time clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12.7 SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
12.8 USB interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
12.9 Display port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
12.10 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
12.11 Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
12.12 Pushbuttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
12.13 License information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
12.13.1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
13 Error causes and troubleshooting 41
13.1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
14 Maintenance 41
14.1 General maintenance information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
14.2 Scheduled maintenance tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
14.3 Battery change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
15 Ordering information 42
15.1 General information on the ordering information. . . . . . . . . . . . . . . . . . . . . . . 42
15.2 Type code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
15.3 Accessories and spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
16 Disposal 44
16.1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
16.2 Return. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
16.3 Packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
17 Service and support 45
Index 46
Table of contents

6 / 50
ctrlX CORE X7
Overview on target groups and product phases
Bosch Rexroth AG
R911419122, Edition 01
1 About this documentation
1.1 Change record
Table 1: Editions of this documentation
Edition Release date Note
Edition 01 2022-12 First edition
1.2 Overview on target groups and product phases
In the following illustration, the framed activities, product phases and target groups refer to the present
documentation.
Example: In the product phase “Mounting (assembly/installation)”, the target group “Mechanic/electri-
cian” can execute the activity “install” using this documentation.
Presales Aftersales
Selection Mounting
(assembly/installation)
Engineering
Commissioning
Operation
Decommissioning
Product
phases
Target
groups
Activities
Design engineer
Programmer
Technologist
Process
specialist
Select
Prepare
Design
Construct
Mechanic/
electrician
Unpack
Mount
Install
Programmer
Commissioning engineer
Parameterize
Program
Configure
Simulate
Technologist
Process specialist
Optimize
Test
Machine
operator
Maintenance
technician
Service
Operate
Maintain
Remove
faults
Create the
NC program
Mechanic/
electrician
Disposal company
Dismount
Dispose
Fig. 1: Assigning the present documentation to the target groups, product phases and activities of the
target group
This document instructs the technical staff of the machine manufacturer on how to safely perform the
mechanical and electrical installation and on how to commission the device.
Required qualification: Individual who is able to assess the tasks assigned and to identify possible
safety risks owing to qualification in the subject, knowledge and experience. The individual should also
be familiar with the standards and regulations.

7 / 50
ctrlX CORE X7
Customer feedback
Bosch Rexroth AG
R911419122, Edition 01
1.3 Scope
This operating instructions is valid for all variants of the control, whose type codes start with:
COREX-M X7
The type code specifications are located on the type plate of the device. Also refer to ⮫ Chapter 2.1
“Product identification” on page 8.
1.4 Related documents
Table 2: Related documentation
Title Part number and document type
Security Manual
Electric Drives
and Controls
⮫ R911342562
Project Planning Manual
Rexroth IndraControl
VAU 01.1
UPS with Communication Interface
⮫ R911336867
Operating Instructions
1.5 Customer feedback
Customer requests, comments or suggestions for improvement are of great importance. Please email
your feedback on the documentations to⮫ [e-mail]. Directly insert
comments into the electronic PDF document and send the PDF file to Bosch Rexroth.
About this documentation

8 / 50
ctrlX CORE X7
Product identification
Bosch Rexroth AG
R911419122, Edition 01
2 Product identification and scope of delivery
2.1 Product identification
1
2
3
4
5
6
7
810 9
11
13
15
17
19
21
2325
26 24
22
20
18
16
14
12
27
Fig. 2: Type plate (example)
1 Company address
2 UKCA marking
3 Underwriters Laboratories Inc. mark
4 CE conformity mark
5 QR or data matrix code, Rexroth, 2D code
6 Type code
7 Product
8 Trademark
9 Plant number
10 Manufacturing date
11 Part number
12 State of revision
13 Serial number
14 Rated voltage
15 Rated current
16 MAC address (Ethernet ID)
17 Free text on the MAC address
18 MAC code (2D code), data matrix
19 EtherCAT
20 S-mark logo
21 KCs mark
22 Service hotline number
23 EAC conformity mark
24 Regulatory Compliance Mark (RCM)
25 China-RoHs 2 label
26 CCC marking
27 Name of origin

9 / 50
ctrlX CORE X7
Explaining signal words and the safety alert symbol
Bosch Rexroth AG
R911419122, Edition 01
2.2 Scope of delivery
•ctrlX CORE control
•24 V power connector, 4-pin (ctrlX CORE X7PLUS)
•Endcover
3 Using safety instructions
3.1 Structure of the safety instructions
The safety instructions are structured as follows:
Burns and chemical burns due to wrong
battery treatment!
CAUTION
Safety alert symbol
Signal word
Avoiding danger
Do not open the batteries and do not heat them over 80 °C.
Consequences and
source of danger
Fig. 3: Structure of the safety instructions
3.2 Explaining signal words and the safety alert symbol
The safety instructions in this documentation contain specific signal words (danger, warning, caution,
notice) and, if necessary, a safety alert symbol (according to ANSI Z535.6).
The signal word draws attention to the safety instruction and indicates the risk potential.
The signal graphics (warning triangle with exclamation mark), added in front of the signal words
Danger, Warning and Caution refer to hazards to inidividuals.
DANGER In case of non-compliance with this safety instruction, death or serious injury
will occur.
WARNING In case of non-compliance with this safety instruction, death or serious injury
can occur.
CAUTION In case of non-compliance with this safety instruction, minor or moderate
injury can occur.
NOTICE In case of non-compliance with this safety instruction, material damage can
occur.
Using safety instructions

10 / 50
ctrlX CORE X7
General information on the intended use
Bosch Rexroth AG
R911419122, Edition 01
3.3 Symbols used
This is a tip.
3.4 Explaining the signal alert symbol on the device
If this symbol is on your device, you have to observe the documentation on the device.
The respective documentation informs on the type of hazard as well as the steps
required to avoid this hazard.
4Intended use
4.1 General information on the intended use
NOTICE Risk of damaging the device if not expressly stated accessories, mounting
parts and other components, cables, lines, software and firmware are used.
The ctrlX CORE control may only be used with the accessories and mounting
parts listed in this documentation. Components that are not expressly men-
tioned must neither be attached nor connected. The same applies to cables
and lines.
Only to be operated with the component configurations and combinations
expressly defined and with the software and firmware specified in the corre-
sponding functional description.
Typical areas of application of the control:
•Handling and assembly systems
•Packaging and food processing machines
•Printing and paper converting machines
•Machine tools
•Wood working machines
•General mechanical engineering
•Building automation
WARNING Danger due to unintended use
The protection specified by Bosch Rexroth cannot be ensured if not used as
intended.
−Use the product exclusively as intended by Bosch Rexroth.
−Operate this device only under the mounting and installation conditions,
in the position and under the ambient conditions (temperature, degree
of protection, humidity, EMC etc.) specified in this documentation.

11 / 50
ctrlX CORE X7
License dongle
Bosch Rexroth AG
R911419122, Edition 01
5 Spare parts, accessories and wear parts
5.1 Power connector, 24 V
Ordering code Part number Description
XACC-1-CSPWRM R911416670 24 V power connector
5.2 SD card
Ordering code Part number Description
XACC-0-SD016GB R911404022 Micro SD card, 16 GB
5.3 RJ45 cable
Ordering code Part number Description
RKB0020 R911340676 Bus cable
5.4 End clamp
Ordering code Part number Description
SUP-M01-ENDHALTER R911170685 2 pieces of snap-on end brackets for 35 mm NS
35/7.5 support rail; width: 9.5 mm
5.5 Fan unit
Ordering code Part number Description
COOLING CTRL. UNIT R911417624 Fan unit
5.6 Endcover
Ordering code Part number Description
XACC-2-ENDCOVR R911412178 Endcover
5.7 License dongle
The license dongle allows to easily transmit licenses between ctrlX controls. The license dongle is a
micro SD card with a serial number. The user can assign licenses to the dongle instead of to the ctrlX
controls.
Ordering code Part number Description
XACC-1-SD*000L R911416693 License dongle
Spare parts, accessories and wear parts

12 / 50
ctrlX CORE X7
Ambient conditions of the ctrlX CORE
Bosch Rexroth AG
R911419122, Edition 01
5.8 Wear parts
5.8.1 Read-only memory
The physical read-only memory (eMMC) of the control has a limited number of write cycles. Retrieve the
current status of the read-only memory via the ctrlX CORE web interface: “ctrlX CORE side navigation
🠂
Settings
🠂
Information
🠂
tab "Resources"
🠂
Sensors” .
Notes on sensor values:
•"0 - 10% of eMMC life time used" means that up to 10 % of the maximum write cycles can be used.
•Create a backup if the value exceeds 80%.
•Replace the hardware if the value exceeds 80%.
•Use an external memory to extend the service life of the permanent memory.
•The frequency of the refresh cycle depends on the service life of the memory. If a refresh cycle is
not possible anymore, data can be lost.
5.8.2 Fan
The maximum service life of the fan unit is 50,000 hours. The fan unit then needs to be replaced. For
the ordering data, refer to⮫ Chapter 5.5 “Fan unit” on page 11.
6 Ambient conditions
6.1 Ambient conditions of the ctrlX CORE
Ambient temperature during operation Up to 2,000 m: -25 °C to +55 °C
2,000 m to 3,000 m: -25 °C to +50 °C
3,000 m to 4,000 m: -25 °C to +45 °C
4,000 m to 5,000 m: -25 °C to +40 °C
Ambient temperature during storage and transport -40 °C to +70 °C
Operating altitude acc. to DIN 60204 Up to 5,000 m above sea level
Permitted air humidity according to
DIN EN 61131-2
5% to 85%, no condensation
Protection class acc. to DIN EN 60 529 IP 20 (not evaluated by UL)
Protection class acc. to DIN EN 61010-2-201 III
Overvoltage category acc. to IEC 60664-1 2
Contamination level acc. to EN 61010-1 2, no condensation allowed
Mechanical tests
Vibration resistance acc. to DIN EN 60068-2-6①Oscillations, sinusoidal in all three axes
5 Hz - 8.4 Hz with 3.5 mm amplitude
8.4 Hz -150 Hz with 1 g peak acceleration
Shock test acc. to DIN EN 60068-2-27 Shock stress: Shock resistance in all three axes, 11
ms semi-sinusoidal 15 g

13 / 50
ctrlX CORE X7
General technical data
Bosch Rexroth AG
R911419122, Edition 01
Broadband noise acc. to DIN EN 60068-2-64 5-20-150 Hz with 0.572 g, 5 h per axis
Electrostatic discharge
ESD resistance acc. to DIN EN 61131-2
•Test voltage
Criterion B
8 kV for air discharge
4 kV for contact discharge
①To avoid vibration, secure the cables at a short distance (< 20 cm).
NOTICE Failure of the product due to contaminated air!
−The ambient air must not contain acids, alkaline solutions, corrosive
agents, salts, metal vapors and other electrically conductive contami-
nants in high concentrations.
−The devices to be installed into the housing and installation compart-
ments must at least comply with the degree of protection IP 54
according to DIN EN 60529.
−The device shall be provided in a suitable fire enclosure in the end-use
application.
NOTICE Defective product due to gases jeopardizing functions
Due to the risk of corrosion, avoid sulphurous gases (e.g. sulphur dioxide
(SO2) and hydrogen sulphide (H2S)). The product is not resistant against
these gases.
NOTICE Failure of the product due to overheating
To avoid overheating and to ensure a smooth operation of the product,
sufficient air has to circulate according to the minimum distances specified,
see Fig. 9.
This is a product that corresponds to the limit values of the emitted interference of class A
(industrial environments). This is a product that does not correspond to the limit values of the
emitted interference of class B (residential area and small enterprises.
When using the product in residential areas or small enterprises, the operator has to take
actions to prevent radio interferences (also refer to DIN EN 55022).
7Technical data
7.1 General technical data
COREX-M-X7
Processor 11th Generation Intel® Core™/I7 Quad Core Processor
RAM 16 GByte DRAM
Internal physical read-only memory
(eMMC)
32 GByte, also refer to ⮫ Chapter 5.8 “Wear parts”
on page 12
Internal non-volatile random-access
memory (NVRAM)
2 Mbyte
Extensions Onboard functions and ctrlX I/O modules
Technical data

14 / 50
ctrlX CORE X7
Voltage supply and current consumption
Bosch Rexroth AG
R911419122, Edition 01
COREX-M-X7
Communication interfaces RJ-45
•5 ×Ethernet connection (10 Mbit, 100 Mbit, 1 Gbit)
Display port •1 ×display port
USB 3 ×USB host, TYPE C (USB3.1), maximum cable length of 3
m
Pushbutton ‒
SD card Slot for SD card
Battery CR1025
Weight 1200 g
Dimensions Refer to ⮫ Chapter 10.1 “Housing dimensions” on page 23
7.2 Voltage supply and current consumption
Nominal voltage at ULand UPDC 24 V SELV/PELV
Maximum permitted voltage range of the supply
voltage ULand UP
DC 18 V to DC 31.2 V (incl. all tolerances and
ripple)
Max. current consumption of the control from ULat
a nominal voltage of 24 V
Typ. 1.7 A (without I/O modules if UL= 24 V), 4.7 A
max. (with 3 A for I/O modules if UL= 24 V)
Max. power consumption of the control from ULat a
nominal voltage of 24 V
Typ. 40.8 W (without I/O modules if UL= 24 V),
112.8 W max. (with 3 A for I/O modules if UL= 24
V)
Current consumption UPTyp. 5 mA (without I/O modules), 8 A max., at UP=
24 V
Power consumption from UPTyp. 0.12 W (without I/O modules), 192 W max.,
at UP= 24 V
Reverse polarity protection of the supply voltage UL
and UP
Present
Fuse protection ULInternal with a protective fuse of 10 A
Fuse protection UPNo internal fuse protection. The operator has to
provide protection against overload by an external
fuse.
Overvoltage protection ULand UPPresent, fuses can trigger in case of overvoltage.
Transient protection ULand UPPresent, suppressor diodes
Pulse load up to 1,500 W
Voltage dips at current supply interfaces PS1 < 1 ms, evaluation criterion A
Electrical isolation
24 V supply (UL/ULGND) to the functional earth
24 V supply (UP/UPGND) to the functional earth
DC 707 V

15 / 50
ctrlX CORE X7
Standards used
Bosch Rexroth AG
R911419122, Edition 01
24 V supply voltage (UL/ULGND and UP/UPGND) to
XF10, XF11, XF12, XF50 and XF52
DC 1200 V
UL/ULGND to UP/UPGND DC 1200 V
NOTICE Electronic damage due to polarity reversal or due to a nominal current that is
too low
The power supply unit has to be able to deliver the quadruple nominal current
of the internal and external fuses to ensure that the fuse reliably triggers in
case of error.
8 Standards
8.1 Standards used
Table 3: Angewandte Normen – Standards used – Normes appliquées
Norm
Standard
Norme
Bedeutung
Meaning
Signification
Ausgabe
Edition
Édition
DIN EN 60204-1 Sicherheit von Maschinen
Elektrische Ausrüstung von Maschinen
–
Safety of machinery
Electrical equipment of machines
–
Sécurité des machines
Equipement électrique des machines
2019
DIN EN 61131-2 Speicherprogrammierbare Steuerungen
Teil 2: Betriebsmittelanforderungen und Prüfungen
–
Programmable controllers
Part 2: Equipment requirements and tests
–
Automates programmables
Partie 2: Spécifications et essais des équipements
2008
DIN EN 60529 Schutzarten durch Gehäuse (IP-Code)
–
Degrees of protection provided by enclosures (IP Code)
–
Degrés de protection procurés par les enveloppes (Code IP)
2014
Standards

16 / 50
ctrlX CORE X7
CE marking
Bosch Rexroth AG
R911419122, Edition 01
Norm
Standard
Norme
Bedeutung
Meaning
Signification
Ausgabe
Edition
Édition
DIN EN 61010-2-201 Sicherheitsbestimmungen für elektrische Mess-, Steuer-, Regel- und Laborgeräte
Teil 2-201: Besondere Anforderungen für Steuer- und Regelgeräte
–
Safety requirements for electrical equipment for measurement, control and labo-
ratory use
Part 2-201: Particular requirements for control equipment
–
Règles de sécurité pour appareils électriques de mesurage, de régulation et de
laboratoire
Partie 2-201: Exigences particulières pour les équipements de commande
2014
UL 61010-2-201 UL Standard for Safety Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use
Part 2-201: Particular Requirements for Control Equipment
2014
8.2 CE marking
8.2.1 Declaration of conformity
The electronic products described in the present operating instructions comply with the requirements
and the target of the following EU directive and with the following harmonized European standards:
Table 4: Normen zur elektromagnetischen Verträglichkeit (EMV) – Standards for electromagnetic
compatibility (EMC) – Normes sur la compatibilité électromagnétique (CEM)
Norm
Standard
Norme
Bedeutung
Meaning
Signification
Ausgabe
Edition
Édition
DIN EN 61000-6-2 Elektromagnetische Verträglichkeit (EMV)
Teil: 6-2: Fachgrundnormen – Störfestigkeit für Industrieber-
eiche
Normes génériques – Immunité pour les environnements
industriels
November 2019
DIN EN 61000-6-4 Elektromagnetische Verträglichkeit (EMV)
Teil: 6-4: Fachgrundnormen – Störaussendung für Industrie-
bereiche
Normes génériques – Norme sur l’émission pour les environ-
nements industriels
September 2011

17 / 50
ctrlX CORE X7
UK declaration of conformity
Bosch Rexroth AG
R911419122, Edition 01
Loss of CE conformity due to modifications at the device.
CE marking applies only to the device upon delivery. After modifying the device, verify the CE
conformity.
For the CE declaration of conformity, go to the Bosch Rexroth media directory: ⮫ www.bos-
chrexroth.com/MediaDirectory, search term ⮫ "DCTC-30455-001".
8.3 UL/CSA certified
The devices "ctrlX CORE" are certified according to:
•UL 61010-2-201 (Industrial Control Equipment) and
•CSA22.2 No. 61010-2-201 (CSA)
However, there can be combinations or extension stages with a limited or missing certification. Thus,
verify the registration according to the UL marking on the device.
Loss of UL/CSA conformity due to modifications at the device.
UL and CSA marking applies only to the device upon delivery. After modifying the device, verify
the UL and the CSA conformity.
To guarantee a UL/CSA-compliant operation, the following conditions have to be met:
−Use only insulated copper wires suitable for at least 60 °C
8.4 UK declaration of conformity
The products comply with the UK directive acc. to S.I. 2016/1091 (electromagnetic compatibility).
For the UK declaration of conformity, go to the Bosch Rexroth media directory: ⮫ www.boschrex-
roth.com/mediadirectory, search term:⮫ "DCTC-30455-031“.
Standards

18 / 50
ctrlX CORE X7
Interface description
Bosch Rexroth AG
R911419122, Edition 01
9 Interfaces
9.1 Interface description
1
2
4
567
8
9
11
3
10
Fig. 4: Interfaces
Table 5: Control interfaces
No. Name Connection type Connector type
(integrated)
Mating connector and cable
(From outside)
①XF01A
XF01B
XF01C
USB host
USB 3.1
USB socket,
Type C
USB plug,
Type C
②CF01 Slot for SD card ‒SD card
③Local bus interface for EtherCAT ‒ ‒
④GB01 Battery case ‒ ‒
⑤XD10 24 V plug UL, UP4-pin 4-pin

19 / 50
ctrlX CORE X7
Interface description
Bosch Rexroth AG
R911419122, Edition 01
No. Name Connection type Connector type
(integrated)
Mating connector and cable
(From outside)
⑥
⑦
XF50
XF52
Ethernet
10/100/1000 MBit
Ethernet (configurable)
XF52 is TSN-capable (Time-Sensitive Networking)
RJ45 socket
8-pin
RJ45 plug
(twisted pair, 8-wire)
⑧
⑨
⑩
XF10
XF11
XF12
Ethernet
10/100/1000 MBit
HMI and engineering port
RJ45 socket
8-pin
RJ45 plug
(twisted pair, 8-wire)
⑪PH02 Display port Display port socket Display port plug
NOTICE Damage of the device by plug mounting under voltage!
−Before mounting or dismounting components, disconnect the control -
including its components - from voltage.
−Connect the voltage only after the control and its components have been
set up.
9.1.1 Local bus interface EtherCAT of ctrlX COREPLUS X7
The local bus connected to the ctrlX COREPLUS at the right is a 100 MBit/s LVDS EtherCAT bus
and the cycle time between 1 ms and 10 ms. The ctrlX COREPLUS can be extended with up to 20
ctrlX I/O modules. The number of connectable modules depends on the total current consumption
of the ctrlX I/O modules. The ctrlX COREPLUS can provide up to 3 A for the current supply of the
modules. The ctrlX COREPLUS supplies the connected I/O modules with the logic voltage ULand the
periphery voltage UP. The voltages and currents fed in are measured internally and applied to the
process data. For UL, only the current consumption of the infeed terminal and the I/O modules. For
the integration into the parent system, the respective ESI files are available. For the ESI files, go to
⮫ http://www.boschrexroth.com/electrics.
Synchronizing the application
The application is synchronized in the "SM synchronous" mode.
Interfaces

20 / 50
ctrlX CORE X7
Interface description
Bosch Rexroth AG
R911419122, Edition 01
Object directory
The object directory contains objects that can be triggered via SDO services. These are defined in the
ETG standards:
Table 6: CoE standard objects
Index (hex) Name
1000 Device type
1001 Error register
1008 Device name
1009 Hardware version
100A Software version
1018 Identify
10F1 Error settings
10F3 Diagnosis history
10F8 Timestamp object
1Ann PDO Mapping TxPDO
1C00 Sync manager type
1C12 Sync manager 2 assignment
1C13 Sync manager 3 assignment
1C33 SM input parameter
F000 Modular device profile
Objects with a module-specific design are described in the following table.