Bosch 3 603 K63 V10 Assembly instructions

Operating / Safety Instructions
Consignes d’utilisation / de sécurité
Instrucciones de funcionamiento y seguridad
GLL40-20G
Professional
GLL40-20G
IMPORTANT:
Read Before Using
IMPORTANT :
Lire avant usage
IMPORTANTE:
Leer antes de usar
English Version
See page 5 Version française
Voir page 20 Versión en español Ver la página 35
1-877-BOSCH99 (1-877-267-2499) www.boschtools.com
GLL40-20G 2610039425 7-18.indd 1 12/31/18 9:26 PM

-2-
7
6
5
2
4
3
8
1
GLL40-20G
GLL40-20G 2610039425 7-18.indd 2 12/31/18 9:26 PM

-3-
1213
9
11
4
3
10
GLL40-20G 2610039425 7-18.indd 3 12/31/18 9:26 PM

-4-
A
B
Make sure that
this device
and the tool
are securely
mounted
before
operation.
Assurez-vous
que cet appareil
et l’outil sont
solidement
assujettis avant de
les utiliser.
Asegúrese de que
este dispositivo
y la herramienta
estén montados
de manera segura
antes de su
utilización.
!
WARNING
!
AVERTISSEMENT
!
ADVERTENCIA
GLL40-20G 2610039425 7-18.indd 4 12/31/18 9:26 PM

-5-
Safety Symbols
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to these
symbols.
This is the safety alert symbol. It
is used to alert you to potential
personal injury hazards. Obey all
safety messages that follow this
symbol to avoid possible injury or
death.
Read manual symbol - Alerts user to
read manual.
WARNING indicates a hazardous
situation which, if not avoided,
could result in death or serious
injury.
GLL40-20G 2610039425 7-18.indd 5 12/31/18 9:26 PM

-6-
Read all instructions. Failure to follow all
instructions listed below may result in
hazardous radiation exposure, electric shock, fire and/or serious
injury. The term “tool” in all of the warnings listed below refers to your
mains-operated (corded) tool or battery-operated (cordless) tool.
The following labels are on your laser tool for
your convenience and safety. They indicate
where the laser light is
emitted by the tool. ALWAYS
BE AWARE of their location
when using the tool.
Do not direct the laser beam at persons or animals
and do not stare into the laser beam yourself. This
tool produces laser class 2 laser radiation and complies
with 21 CFR 1040.10 and 1040.11 except for deviations
pursuant to Laser Notice No. 50, dated June 24, 2007. This can lead
to persons being blinded.
DO NOT remove or deface any warning or caution labels.
Removing labels increases the risk of exposure to laser radiation.
Use of controls or adjustments or performance of procedures
other than those specified in this manual, may result in hazardous
radiation exposure.
ALWAYS make sure that any bystanders in the vicinity of use
are made aware of the dangers of looking directly into the laser
tool.
DO NOT place the laser tool in a position that may cause
anyone to stare into the laser beam intentionally or
unintentionally. Serious eye injury could result.
General Safety Rules
<5 mW @ 500-540 nm
GLL40-20G 2610039425 7-18.indd 6 12/31/18 9:26 PM

-7-
ALWAYS position the laser tool securely. Damage to the laser
tool and/or serious injury to the user could result if the laser tool fails.
ALWAYS use only the accessories that are recommended by
the manufacturer of your laser tool. Use of accessories that have
been designed for use with other laser tools could result in serious
injury.
DO NOT use this laser tool for any purpose other than those
outlined in this manual. This could result in serious injury.
DO NOT leave the laser tool “ON” unattended in any operating
mode.
DO NOT disassemble the laser tool. There are no user
serviceable parts inside. Do not modify the product in any way.
Modifying the laser tool may result in hazardous laser radiation
exposure.
DO NOT use the laser viewing glasses as safety goggles. The
laser viewing glasses are used for improved visualization of the laser
beam, but they do not protect against laser radiation.
DO NOT use the laser viewing glasses as sun glasses or
in traffic. The laser viewing glasses do not afford complete UV
protection and reduce color perception.
DO NOT use any optical tools such as, but not limited to,
telescopes or transits to view the laser beam. Serious eye injury
could result.
DO NOT stare directly at the laser beam or project the laser
beam directly into the eyes of others. Serious eye injury could
result.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
GLL40-20G 2610039425 7-18.indd 7 12/31/18 9:26 PM

-8-
DO NOT operate the laser tool around children or allow children
to operate the laser tool. Serious eye injury could result.
DO NOT use laser tools, attachments and accessories outdoors
when lightning conditions are present.
Do not operate the measuring tool in explosive environments,
such as in the presence of flammable liquids, gases or dusts.
Sparks can be created in the measuring tool which may ignite the
dust or fumes.
Electrical safety
Batteries can explode or leak, cause injury or
fire. To reduce this risk, always follow all
instructions and warnings on the battery label and package.
DO NOT short any battery terminals.
DO NOT charge alkaline batteries.
DO NOT mix old and new batteries. Replace all of them at the same
time with new batteries of the same brand and type.
DO NOT mix battery chemistries.
Dispose of or recycle batteries per local code.
DO NOT dispose of batteries in fire.
Keep batteries out of reach of children.
Remove batteries if the device will not be used for several months.
Personal safety
If laser radiation strikes your eye, you must deliberately close
your eyes and immediately turn your head away from the beam.
Do not make any modifications to the laser equipment.
GLL40-20G 2610039425 7-18.indd 8 12/31/18 9:26 PM

-9-
Stay alert, watch what you are doing and use common sense
when operating a tool. Do not use a tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating a tool may result in serious personal injury
or incorrect measurement results.
Use safety equipment. Always wear eye protection. Safety
equipment such as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions will reduce personal
injuries.
Use caution when using laser tools in the vicinity of electrical
hazards.
Magnets
Keep the tool, positioning device, and laser target
plate away from cardiac pacemakers. The magnets
of the tool and laser target plate generate a field that can
impair the function of cardiac pacemakers.
Keep the tool, positioning device, and laser target plate away
from magnetic data medium and magnetically-sensitive
equipment. The effect of the magnets of the tool and laser target
plate can lead to irreversible data loss.
Use and care
Use the correct tool for your application. The correct tool will do
the job better and safer.
GLL40-20G 2610039425 7-18.indd 9 12/31/18 9:26 PM

-10-
Do not use the tool if the switch does not turn it on and off. Any
tool that cannot be controlled with the switch is dangerous and must
be repaired.
Store idle tool out of the reach of children and do not allow
persons unfamiliar with the tool or these instructions to operate
the tool. Tools are dangerous in the hands of untrained users.
Maintain tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may
affect the operation. If damaged, tool repaired before use. Many
accidents are caused by poorly maintained tools.
Use the tool, accessories, etc., in accordance with these
instructions and in the manner intended for the particular type
of tool, taking into account the working conditions and the work
to be performed. Use of the tool for operations different from those
intended could result in a hazardous situation.
Service
Have your tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the
tool is maintained.
Develop a periodic maintenance schedule for tool. When
cleaning a tool be careful not to disassemble any portion of the
tool since internal wires may be misplaced or pinched or may
be improperly mounted. Certain cleaning agents such as gasoline,
carbon tetrachloride, ammonia, etc. may damage plastic parts.
SAVE THESE INSTRUCTIONS
GLL40-20G 2610039425 7-18.indd 10 12/31/18 9:26 PM