Bosch GLM165-10 Assembly instructions

IMPORTANT:
Read Before Using
IMPORTANT :
Lire avant usage
IMPORTANTE:
Leer antes de usar
For English Version
See page 4
Version française
Voir page 19
Versión en español
Ver la página 36
Operating/Safety Instructions
Consignes d’utilisation/de sécurité
Instrucciones de funcionamiento y seguridad
1-877-BOSCH99 (1-877-267-2499) www.boschtools.com
GLM165-10
Call Toll Free for Consumer Information and Service Locations
Pour obtenir des informations et les adresses de nos centers de service
après-vente, appelez ce numéro gratuit
Llame gratis para obtener información para el consumidor y
ubicaciones de servicio
2610047291 90x145.indd 1
4/7/17 10:12 AM

2
13
2
87
6
5
4
e
g
f
h
d
ab
c
2610047291 90x145.indd 2
4/7/17 10:12 AM

3
1
A
1'6"
1'
B
2.
1.
g
f
f
h
2610047291 90x145.indd 3
4/7/17 10:12 AM

4
General Safety Rules
Safety Symbols
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to these
symbols.
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
Read manual symbol - Alerts user to read manual.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
DO NOT operate the laser tool around children or allow chil-
dren to operate the laser tool. Serious eye injury could result.
DO NOT use measuring tools, attachments and accessories
outdoors when lightening conditions are present.
Read all instructions. Failure to follow all
instructions listed below may result in
hazardous radiation exposure, electric shock, fire and/or
serious injury. The term “tool” in the warnings listed below
refers to your mains-operated (corded) tool or battery-operated
(cordless) tool.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
2610047291 90x145.indd 4
4/7/17 10:12 AM

5
Electrical safety
Batteries can explode or leak, cause
injury or fire.To reduce this risk, always
follow all instructions and warnings on the battery label
and package.
Do not short any battery terminals.
Do not charge alkaline batteries.
Do not mix old and new batteries. Replace all of them at
the same time with new batteries of the same brand and
type.
Do not mix battery chemistries.
Dispose of or recycle batteries per local code.
Do not dispose of batteries in fire.
Keep batteries out of reach of children.
Remove batteries if the device will not be used for several
months.
Personal safety
Stay alert, watch what you are doing and use common
sense when operating a measuring, detection and layout
tool. Do not use a measuring, detection and layout tool
while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating
measuring, detection and layout tools may result in serious
personal injury or incorrect measurement results.
Use safety equipment. Always wear eye protection. Safety
equipment such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
DO NOT use any optical tools such as, but not limited to,
telescopes or transits to view the laser beam. Serious eye
injury could result.
DO NOT stare directly at the laser beam or project the laser
beam directly into the eyes of others. Serious eye injury
could result.
Use caution when using measuring tools in the vicinity of
electrical hazards.
2610047291 90x145.indd 5
4/7/17 10:12 AM

6
Measuring, detection and layout tool use and
care
Use the correct measuring, detection and layout tool for
your application. The correct measuring, detection and layout
tool will do the job better and safer at the rate for which it was
designed.
Do not use the measuring, detection and layout tool if the
switch does not turn it on and off. Any measuring, detection
and layout tool that cannot be controlled with the switch is dan-
gerous and must be repaired.
Store idle measuring, detection and layout tools out of the
reach of children and do not allow persons unfamiliar with
the measuring, detection and layout tool or these instruc-
tions to operate the measuring, detection and layout tool.
Measuring, detection and layout tools may be dangerous in the
hands of untrained users.
Maintain measuring, detection and layout tools. Check for
misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the measuring, de-
tection and layout tools operation. If damaged, have the
measuring, detection and layout tool repaired before use.
Many accidents are caused by poorly maintained measuring,
detection and layout tools.
Use the measuring, detection and layout tool, accessories,
etc., in accordance with these instructions and in the man-
ner intended for the particular type of measuring, detection
and layout tool, taking into account the working conditions
and the work to be performed. Use of the measuring, detec-
tion and layout tool for operations different from those intended
could result in a hazardous situation.
Service
Have your measuring, detection and layout tool serviced by
a qualified repair person using only approved replacement
parts. This will ensure that the safety of the measuring, detec-
tion and layout tool is maintained.
Develop a periodic maintenance schedule for your measur-
ing, detection and layout tool. Follow checking and recali-
bration procedures outlined in the instruction manual.
2610047291 90x145.indd 6
4/7/17 10:12 AM

7
When cleaning a tool be careful not to disassemble any
portion of the tool since internal wires may be misplaced
or pinched or may be improperly mounted. Certain cleaning
agents such as gasoline, carbon tetrachloride, ammonia, etc.
may damage plastic parts.
Safety Rules for Laser Tools
The following label is on your laser tool for your safety. AL-
WAYS BE AWARE of its location when using the tool.
DO NOT direct the laser beam at persons or
animals and do not stare into the laser beam
yourself.This tool produces class 2 laser radia-
tion and complies with 21 CFR 1040.10 and
1040.11 except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007.This can lead to persons
being blinded.
DO NOT place the measuring tool in a position that may
cause anyone to stare into the laser beam intentionally or
unintentionally. Serious eye injury could result.
Never aim the beam at a workpiece with a reflective surface.
Bright shiny reflective sheet steel or similar reflective
surfaces are not recommended for laser use. Reflective
surfaces could direct the beam back towards the operator.
DO NOT operate the measuring tool around children or
allow children to operate the measuring tool. Serious eye
injury could result.
ALWAYS: Make sure that any bystanders in the vicinity of
use are made aware of the dangers of looking directly into
the measuring tool.
DO NOT remove or deface any warning or caution labels.
Removing labels increases the risk of exposure to laser
radiation.
2610047291 90x145.indd 7
4/7/17 10:12 AM

8
DO NOT operate the measuring tool in combustible areas
such as in the presence of flammable liquids, gases or dust.
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
Do not use the laser viewing glasses as sun glasses or in
traffic. The laser viewing glasses do not afford complete UV
protection and reduce color perception.
DO NOT leave measuring tool “ON” unattended in any
operation mode.
ALWAYS turn the measuring tool “OFF” when not in use.
Leaving the measuring tool “ON” increases the risk of someone
inadvertently staring into the laser beam.
ALWAYS position the measuring tool securely. Damage to
the measuring tool and/or serious injury to the user could result
if the measuring tool falls.
Take care to recognize the accuracy and range of the
device. Measurement may not be accurate if used beyond the
rated range of the device.
ALWAYS use only the accessories that are recommended
by the manufacturer of your measuring tool. Use of
accessories that have been designed for use with other
measuring tools could result in serious injury.
DO NOT use this measuring tool for any purpose other
than those outlined in this manual. This could result in
serious injury.
ALWAYS remove the batteries when cleaning the laser light
aperture and laser lens.
DO NOT disassemble the measuring tool.There are no user
serviceable parts inside. Disassembling the laser will void
all warranties on the product. Do not modify the product in
any way. Modifying the measuring tool may result in hazardous
laser radiation exposure.
Repair and servicing must always be performed by a
qualified repair facility. Repairs performed by unqualified
personnel could result in serious injury.
2610047291 90x145.indd 8
4/7/17 10:12 AM

9
Features
The numbering of the product features shown refers to the illustration
of the measuring tool on the graphic page.
1Measuring (On/Off) Button
2 Display
3 Battery lid
4Latch of battery lid
5Serial number
6Laser warning label
7Reception lens
8Laser beam outlet
Display Elements
aTemperature warning
bBattery low indicator
cMeasuring function
Auto-square footage (or
m2) measurement
dLaser switched on
eUnit of measure
fMeasurement value after 1st
press
gMeasurement value after 2nd
press
hAuto-square total
The measuring tool is intended for measuring distances,
lengths, heights and clearances. The measuring tool is
suitable for measuring only indoors.
Intended Use
2610047291 90x145.indd 9
4/7/17 10:12 AM

10
Digital Laser Measure GLM165-10
Measuring range (typical) 6 in - 165 ft (0.15 –50 mA)
Measuring accuracy (typical) ±1/16 in (±1.5 mmB)
Lowest indication unit 1/32 in (1 mm)
Automatic switch-off after approx.
- Laser 20 s
- Measuring Tool 5 min
Operating temperature +14° F to 113° F (-10° C to +45° C)
Storage temperature -4° F to 158° F (-20° C to +70° C)
Relative air humidity, max. 90 %
Laser class 2
Laser type 635 nm, <1mW
Laser beam diameter at 77° F (25 °C)
- at 30 ft (10 m) distance, approx. 3/8 in (9 mm)
- at 165 ft (50 m) distance, approx. 1-3/4 in (45 mm)
Batteries 2 x 1.5V (AAA)
Battery service life in measuring operation, approx. 5 h
Degree of Protection IP54 (dust and splash water protected)C
Weight 0.2 lb (0.09 kg)
Dimensions 4.1 x 1.6 x 0.9 in (105 x 41 x 24 mm)
A) The working range increases depending on how well the laser light is reflected from
the surface of the target (scattered, not reflective) and with increased brightness of
the laser point to the ambient light intensity (interior spaces, twilight). In unfavorable
conditions, e.g., with extreme interior illumination or a badly reflecting surface, the
measuring range may be limited.
B) In favorable conditions, a deviation influence of ±0.05 mm/m must be taken
into account. In unfavorable conditions, e.g., with extreme illumination, badly
reflecting surface or the room temperature deviating heavily from 77 °F (25 °C),
the maximum deviation can be up to ±3.0mm. Additionally, a deviation influence
of 0.15mm/m must be taken into account.
C) Does not apply to battery compartment.
The measuring tool can be clearly identified with the serial
number 5on the type plate.
Technical Data
2610047291 90x145.indd 10
4/7/17 10:12 AM

11
Assembly
Inserting/Replacing the Batteries
AAA Alkaline batteries are recommended for the measuring
tool.
To open the battery lid 3, press the latch 4in the direction of
the arrow and remove the battery lid. Insert the batteries.When
inserting, pay attention to the correct polarity according to the
representation on the inside of the battery compartment.
When the battery symbol appears for the first time on the
display, measurements are still possible for approx. 15 minutes.
When the battery symbol flashes, the batteries must be
replaced; measurements are no longer possible.
Always replace all batteries at the same
time. Only use batteries from one
brand and with the identical capacity.
Remove the batteries from the tool when not using it for
extended periods. When storing for extended periods, the
batteries can corrode and discharge themselves.
Operation
Protect the tool against moisture and
direct sun irradiation.
Do not subject the tool to extreme temperatures or
variations in temperature. As an example, do not leave
it in vehicles for longer periods. In case of large variations
in temperature, allow the tool to adjust to the ambient
temperature before putting it into operation. In case of extreme
temperatures or variations in temperature, the accuracy of the
tool can be impaired.
Avoid heavy impact or falling of the tool. After heavy exterior
impact on the tool, an accuracy check should always be
carried out before continuing to work (see “Accuracy Check of
the Distance Measurement”, page 14).
DO NOT stare directly at the laser beam
or project the laser beam directly into
the eyes of others. Serious eye injury could result.
2610047291 90x145.indd 11
4/7/17 10:12 AM

12
Do not leave the switched on measuring tool unattended
and switch the tool off after use. Other persons could be
blinded by the laser beam.
Switching On and Off
To switch on the measuring tool, push down the On/Off button
1. When switching on the measuring tool, the laser beam is
switched on. The laser indicator flashes on the display.
To switch off the measuring tool, push down the On/Off button
1and hold for 3 seconds.
When no button on the measuring tool is pressed for approx.
5 minutes, the measuring tool automatically switches off to
save the batteries.
Measuring Procedure (See Figure A)
Once switched on, the measuring tool is in the real time
measurement mode. Laser is automatically activated and tool
is measuring.
The rear edge of the measuring tool is always the reference
point for the measurement that is being taken.
Place the measuring tool against the desired starting point of
the measurement (e.g. a wall).
Measuring Functions
Real Time Measurement
For real time measurements, the measuring tool can be moved
relative to the target. In this manner for example, the distance
displayed on the screen will change in real time as you move
further or closer to the measured target.
Auto Total for Square Footage or Square Meters (See Figure
B)
The auto total feature automatically calculates the product
of two individual measurements (e.g. to determine square
footage/meters)
The auto-total value is not saved. It is erased as soon as a
third measurement is taken, device is switched off or if device
automatically switches off when no button is pressed after 5
minutes. A subsequent corrections of the auto-total is not
possible.
2610047291 90x145.indd 12
4/7/17 10:12 AM

13
1. Press measuring button 1to activate laser. The laser will
be switched on and measuring will begin immediately.
The current measurement fis indicated at the top of
the display. Press the measuring button 1again to hold
the measurement. The held measurement fwill remain
displayed at the top of the display.
2. The laser beam remains switched on between the two
measurements. The second measurement gwill appear on
the second line. After the second measurement has been
completed, the area will be automatically calculated and
displayed. The end result hwill be shown at the bottom
of the display, while the current measured value gwill be
shown above it.
After the second measurement has been taken, the laser
beam is automatically switched off.
By pressing the measuring button 1again, the laser is
reactivated and the original two measurements are cleared.
Changing the Unit of Measure
Switch off the measuring tool. Press the measuring button 1
and hold it down. The display will alternately show three units
of measure. When the desired setting is displayed, release
the measuring button1. The setting is saved.
Display Illumination
The display illumination is continuously switched on. When
no button is pressed, the display illumination is dimmed after
approx. 10 seconds to preserve the batteries. When no button
is pressed for approx. 30 seconds, the display illumination
goes out.
2610047291 90x145.indd 13
4/7/17 10:12 AM

14
Working Advice
General Information
The reception lens 7and the laser beam outlet 8must not be
covered when taking a measurement.
Measurement takes place at the center of the laser beam,
even when target surfaces are at a slope.
Influence Effects on the Measuring Range
The measuring range depends on the light conditions and the
reflection properties of the target surface.
Influence Effects on the Measuring Result
Due to physical effects, faulty measurements cannot be
excluded when measuring on different surfaces. Included
here are:
– Transparent surfaces (e.g., glass, water),
– Reflecting surfaces (e.g., polished metal, glass),
– Porous surfaces (e.g. insulation materials),
– Structured surfaces (e.g., roughcast, natural stone).
Also, air layers with varying temperatures or indirectly received
reflections can affect the measured value.
Accuracy Check of the Distance Measurement
The accuracy of the distance measurement can be checked
as follows:
– Select a permanent measuring section with a length of
approx. 3 ft to 33 ft (1 m to 10 m); its length must be precisely
known (e.g. the width of a room or a door opening). The
measuring distance must be indoors; the target surface for
the measurement must be smooth and reflect well.
– Measure the distance 10 times after another.
The deviation of the individual measurements from the
mean value must not exceed ±1/8” (±3.0mm). Log the
measurements, so that you can compare their accuracy at a
later point of time.
2610047291 90x145.indd 14
4/7/17 10:12 AM

15
Troubleshooting
Cause Corrective Measure
Temperature warning indicator (a) flashing;
measurement not possible
Measuring tool not within the
temperature range between
+14°F and 104°F ( –10°C and
+40°C)
Wait until the measuring
tool has reached the
operating temperature
Battery low indicator (b) appears
Battery voltage decreasing
(measurement still possible) Replace batteries
Battery low indicator (b) flashing; measurement not
possible
Battery voltage too low Replace batteries
All indicators on the display flashing
The measuring tool is defective Contact the Customer
Service
2610047291 90x145.indd 15
4/7/17 10:12 AM

16
Maintenance and Service
Keep the measuring tool clean at all
times.
Do not immerse the measuring tool into water or other
fluids.
Wipe off debris using a moist and soft cloth. Do not use any
cleaning agents or solvents.
Maintain the reception lens 7 in particular, with the same
care as required for eye glasses or the lens of a camera.
If the measuring tool should fail despite the care taken
in manufacturing and testing procedures, repair should
be carried out by an authorized after-sales service center
for Bosch power tools. Do not open the measuring tool
yourself.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the measuring tool.
ENVIRONMENT PROTECTION
Recycle raw materials and batteries instead
of disposing of waste. The unit, accessories,
packaging and used batteries should be sorted for
environmentally friendly recycling in accordance with
the latest regulations.
2610047291 90x145.indd 16
4/7/17 10:12 AM

17
Robert Bosch Tool Corporation (“Seller”) warrants to the original
purchaser only, that all Bosch lasers and measuring tools will
be free from defects in material or workmanship for a period of
one (1) year from date of purchase. Bosch will extend warranty
coverage to two (2) years when you register your product within
eight (8) weeks after date of purchase. Product registration
card must be complete and mailed to Bosch (postmarked
within eight weeks after date of purchase), or you may register
on-line at www.boschtools.com/Service/ProductRegistration. If
you choose not to register your product, a one (1) year limited
warranty will apply to your product.
30 Day Money Back Refund or Replacement -
If you are not completely satisfied with the performance of your
laser and measuring tools, for any reason, you can return it to
your Bosch dealer within 30 days of the date of purchase for
a full refund or replacement. To obtain this 30-Day Refund or
Replacement, your return must be accompanied by the original
receipt for purchase of the laser or optical instrument product. A
maximum of 2 returns per customer will be permitted.
SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE
REMEDY under this Limited Warranty and, to the extent
permitted by law, any warranty or condition implied by law, shall
be the repair or replacement of parts, without charge, which are
defective in material or workmanship and which have not been
misused, carelessly handled, or misrepaired by persons other
than Seller or Authorized Service Center. To make a claim under
this Limited Warranty, you must return the complete Bosch laser
or measuring tool, transportation prepaid, to any BOSCH Factory
Service Center or Authorized Service Center. Please include a
dated proof of purchase with your tool. For locations of nearby
service centers, please use our on-line service locator or call
1-877-267-2499.
LIMITED WARRANTY OF BOSCH LASER AND
MEASURING TOOL PRODUCTS
2610047291 90x145.indd 17
4/7/17 10:12 AM

18
THIS WARRANTY PROGRAM DOES NOT APPLY TO
TRIPODS AND RODS. Robert Bosch Tool Corporation
(“Seller”) warrants tripods and leveling rods for a period of one
(1) year from date of purchase.
THIS LIMITED WARRANTY DOES NOT APPLY TO OTHER
ACCESSORY ITEMS AND RELATED ITEMS. THESE ITEMS
RECEIVE A 90 DAY LIMITED WARRANTY.
To make a claim under this Limited Warranty, you must return
the complete product, transportation prepaid. For details to
make a claim under this Limited Warranty please visit www.
boschtools.com or call 1-877-267-2499.
ANY IMPLIED WARRANTIES SHALL BE LIMITED IN
DURATION TO ONE YEAR FROM DATE OF PURCHASE.
SOME STATES IN THE U.S., AND SOME CANADIAN
PROVINCES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
(INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS
OF PROFITS) ARISING FROM THE SALE OR USE OF
THIS PRODUCT. SOME STATES IN THE U.S., AND SOME
CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, ANDYOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE IN THE U.S., OR PROVINCE
TO PROVINCE IN CANADA AND FROM COUNTRY TO
COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS
SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA
AND THE COMMONWEALTH OF PUERTO RICO. FOR
WARRANTY COVERAGE WITHIN OTHER COUNTRIES,
CONTACT YOUR LOCAL BOSCH DEALER OR IMPORTER.
2610047291 90x145.indd 18
4/7/17 10:12 AM

19
Symboles relatifs à la sécurité
Les définitions ci-dessous décrivent le niveau de gravité pour
chaque terme signalant un danger. Veuillez lire le mode d’emploi
et lire la signification de ces symboles.
C’est le symbole d’alerte relatif à la sécurité. Il est utilisé
pour vous avertir de l’existence possible d’un danger de
lésion corporelle. Obéissez à tous les messages relatifs à la
sécurité qui suivent ce symbole pour éviter tout risque de
blessure ou même de mort.
Symbole de lecture du mode d’emploi - Alerte l’utilisateur
pour lire le mode d’emploi.
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, pourrait causer la mort d’une
personne ou une blessure grave.
Consignes générales de sécurité
Lisez toutes les instructions.
La non-observation de
toutes les instructions figurant ci-après pourrait causer une
exposition à des rayonnements dangereux, un choc
électrique, un incendie et/ou des blessures personnelles
graves. Le terme « outil » dans les avertissements ci-dessous
fait référence à votre outil électrique à cordon électrique
branché dans une prise secteur ou à votre outil électrique à
piles (sans fil).
CONSERVEZ TOUS LES AVERTISSEMENTS ET TOUTES
LES INSTRUCTIONS POUR RÉFÉRENCE FUTURE
2610047291 90x145.indd 19
4/7/17 10:12 AM

20
Sécurité de la zone de travail
Gardez votre zone de travail propre et bien éclairée. Des
zones encombrées ou sombres sont propices aux accidents.
N’utilisez PAS l’outil laser à proximité d’enfants, et ne lais-
sez pas des enfants se servir de l’outil laser. Ceci pourrait
causer de graves blessures aux yeux.
N’utilisez PAS d’outils de mesure, d’attachements et
d’accessoires à l’extérieur lorsque des conditions de fou-
dre sont présentes.
Sécurité électrique
Les piles peuvent exploser
ou fuir,causer des blessures
ou un incendie. Pour réduire ce risque, suivez toujours
toutes les instructions et tous les avertissements figurant
sur l’étiquette et l’emballage des piles.
Ne court-circuitez pas de bornes de piles.
Ne chargez pas de piles alcalines.
Ne combinez pas des piles usagées et des piles neuves.
Remplacez toutes les piles en même temps par de
nouvelles piles de la même marque et du même type.
Ne mélangez pas de propriétés chimiques de piles
différentes.
Mettez les piles au rebut ou recyclez-les conformément
aux dispositions de votre code local.
Ne jetez pas de piles dans un feu.
Gardez les piles hors de la portée des enfants.
Retirez les piles si vous pensez que vous n’utiliserez pas
l’appareil pendant plusieurs mois.
Sécurité personnelle
Restez alerte, surveillez ce que vous êtes en train de faire
et faites preuve de bon sens lorsque vous utilisez un outil
de mesure, de détection et de configuration. N’utilisez pas
d’outil de mesure, de détection et de configuration si vous
êtes fatigué(e) ou sous l’influence de drogues, d’alcool ou
de médicaments. Un simple moment d’inattention pendant
que vous utilisez un outil de mesure, de détection et de
2610047291 90x145.indd 20
4/7/17 10:12 AM