Bosch LTC 9113/00 User manual

Instruction Manual
EN Rack-mount Kits
LTC 9113/00, LTC 9114/00, LTC 9115/00,
LTC 9017/00, LTC 9117/00

1DESCRIPTION
These kits are designed to mount the following
monitors in a standard EIA 19in. rack using either
Universal or Wide Spacing.
Rack Kit Monitor Model
LTC 9113/00 LTC 2813/90, & LTC 2 914/91
LTC 9114/00 LTC 2814/90
LTC 9115/00 LTC 2915/90
LTC 9017/00 LTC 2017/50 & LTC 2017/6 0
LTC 9117/00 LTC 2917/91
2UNPACKING
This mechanical equipment should be unpacked and
handled with care.
Check for the following items:
Qty. Item
1Base Tray
2Rack Sides
1Cover Bezel
1Hardware Kit containing the following items:
4 4-40 Machine Screws (Cover Bezel)
6 8-32 Machine Screws (Rack Sides)
4 10-32 Machine Screws (Rack Installation)
4 10-32 U-type Nut Fasteners (Rack
Installation)
If an item appears to have been damaged in shipment,
replace it properly in its carton and notify the shipper.
If any items are missing, notify your Bosch Security
Systems Inc. Sales Representative or Customer Service.
The shipping carton is the safest container in which the
unit may be transported. Save it for possible future use.
3SERVICE
If the unit ever needs repair service, the customer
should contact the nearest Bosch Security Systems, Inc.
Service Center for return authorization and shipping
instructions.
Service Centers
USA
Phone: [phone] or 717-735-6638
fax: [phone] or 717-735-6639
CCTV Spare Parts
Phone: [phone] or 408-956-3853 or 3854
fax: [phone]
e-mail: [email protected].com
Canada
Phone: [phone]
Europe, Middle East & Asia Pacific Region
Phone: [phone]
For additional information, see
www.boschsecuritysystems.com.
4INSTALLATION
4.1 ASSEMBLY
4.1.1 Tools Required
Small Phillips screwdriver.
Assembly
1. Position the monitor so that it is upside down,
with its feet (where applicable) on top, and the
front of the monitor toward you. Remove and
retain each replacement foot and mounting
screw from the monitor. Install the base tray
onto the monitor with the flat side of the base
tray toward the monitor; the edges of the base
tray should face up. The square hole of the base
tray should now be at the lower left-hand edge
of the tray. Align the removable foot mounting
holes with the appropriate holes in the base tray.
Secure the monitor to the base tray using the
reserved mounting screws from the removable
feet.
EN |2
Bosch Security Systems | 19 August 2004
LTC 9113/00, LTC 9114/00, LTC 9115/00, LTC 9017/00, LTC 9117/00 | Instruction Manual | Description

EN |3
Bosch Security Systems | 19 August 2004
FIGURE 1 Installing the Base Tray
NOTES:
•If the monitor does not have removable feet
(LTC 2917/90 and LTC 2813/60 monitors), align
the pads on the monitor base with the holes
in the base tray. Secure the monitor to the
base with sheet metal screws (not provided);
self-threading sheet metal screws with a
maximum length of 19mm (3/4in.) are
recommended. While attaching the monitor to
base tray, do not push in the plastic stand-offs
protruding from the bottom of the monitor, as
this may damage the monitor’s internal
workings.
•When installing the LTC 9113/00, use the
front-most set of holes in the base tray so that
the flip-down drawer on the monitor is still
accessible once installed in the rack.
2. Align the two (2) rack side panels with the sides
of the base tray, and attach using the six (6)
supplied 8-32 screws.
FIGURE 2 Attaching the Side Panels
3. Install the unit (monitor, base tray, and 2 rack
side panels) into the rack. If necessary, use the
four (4) supplied 10-32 screws and U-type nut
fasteners.
FIGURE 3 Installing the Unit into the Rack
4. Install the cover bezel using the four (4)
supplied 4-40 machine screws, inserted into
the holes in the rack side panels.
FIGURE 4 Installing the Cover Bezel
LTC 9113/00, LTC 9114/00, LTC 9115/00, LTC 9017/00, LTC 9117/00 | Instruction Manual | Installation
Removable
Feet
Orientation Hole
OSD
ABY/CS
EQ
4-40 Screws (4)
10-32 Screws (4)
U-Nut (4)
(Optional)
(Monitor Shown
Installed in Rack Kit)
19in. EIA Rack

© 2004 Bosch Security Systems GmbH
3935 890 14616 04-34 | Updated August 19, 2004 | Data subject to change without notice.
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 USA
Tel: [phone]
Fax: [phone]
www.boschsecuritysystems.com
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Tele [phone]
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Republic of Singapore
Tel: [phone]