Bosch FAA-350-B6 User manual

Smoke detector POPIT base
FAA‑350‑B6
en Installation manual

Smoke detector POPIT base Table of contents | en 3
Bosch Security Systems B.V. 2022.09 | 01 | F.01U.396.537
Table of contents
1Safety 4
2Overview 4
3Installation 5
3.1 Installing the base 6
3.2 Wiring 6
4Base POPIT addresses 8
5Technical data 15
5.1 Wire lengths 15

4en | Safety Smoke detector POPIT base
2022.09 | 01 | F.01U.396.537 Bosch Security Systems B.V.
1 Safety
i
Notice!
NFPA
Installation must be carried out by trained and authorized
personnel.
i
Notice!
Make sure the volume of the electrical box you use is adequate
to accommodate the number and size of conductors as
specified by the National Electrical Code (NEC) or any local
regulations having jurisdiction.
2 Overview
These instructions cover the installation of the Addressable
Detector POPIT bases in an addressable system.
This device with built-in POPIT, provides individual addresses on
the G Series control panel POPEX bus. These bases accept the
FCP-350 Series Photoelectric Smoke Detector and FCH-350-135
Heat Detector Heads.
i
Notice!
Heat detector head voltage compatibility
The FAH-350-135 Heat Detector Heads can only be used at 24
V.
i
Notice!
FAH-350-190 high temperature
The FAH-350-190 Heat Detector head should not be used with
the FAA-350-B6 POPIT base due to a higher temperature
threshold from the FAH-350-190 detector head. The
temperature range is too high for the electronics in the
FAA-350-B6 POPIT base and may not signal an alarm/trouble
event.

Smoke detector POPIT base Installation | en 5
Bosch Security Systems B.V. 2022.09 | 01 | F.01U.396.537
23
5
4
1
6
1 Mounting holes for
electrical back box
2 Address selection DIP
switch
3 S1 (in) /S2 (out) 12/24
VDC Switched Aux power
(-)
4 L4 (in/out) 12/24 VDC
Switched Aux power (+)
5 H1 (in/out) POPEX bus
(+)
6 H2 (in/out) POPEX bus (-)
3 Installation
Danger!
Install, test, and maintain this device according to these
instructions, NFPA 72 standards, local codes, and the Authority
Having Jurisdiction (AHJ) in your area.

6en | Installation Smoke detector POPIT base
2022.09 | 01 | F.01U.396.537 Bosch Security Systems B.V.
i
Notice!
Make sure the volume of the electrical box you use is can
accommodate the number and size of conductors as specified
by the National Electrical Code (NEC) or any local regulations
having jurisdiction.
3.1 Installing the base
Depending on the local regulations, you can surface mount the
base using anchors, mollies, or wing nuts.
1. Run all system wiring.
2. Mount the base using the two oblong mounting holes. Fits 4
in square, octagon, AB, and single-gang back boxes.
3. Tighten the base to the mounting surface. Tighten until
snug, but not distorted.
3.2 Wiring
i
Notice!
Do not twist the wires or loop them around the terminals.
i
Notice!
When using a separate supply, connect the negative side to the
control panel ground.
1. Cut, strip, and place the in and out wires for terminal
connection as individual ends.
2. Connect the power loop to the control panel’s switched
auxiliary power.

Smoke detector POPIT base Installation | en 7
Bosch Security Systems B.V. 2022.09 | 01 | F.01U.396.537
1 1 1
(+)
(-)
(+)
(-)
2
3
1 FAA-350-B6 2 Switched auxiliary power
3 POPIT Bus
Remote LED Installation
1
(+)
(-)
2
3
1 Remote LED (DRA-5
shown for 12V
installations only)
2 Black wire (to Terminal
S2)
3 Red wire (to Terminal L2)

8en | Base POPIT addresses Smoke detector POPIT base
2022.09 | 01 | F.01U.396.537 Bosch Security Systems B.V.
4 Base POPIT addresses
Each detector base has a specific address point that is
determined by setting the seven DIP switches on the detector’s
base. The base address number does not depend on the base
location in the circuit.
If adding the base to an FACP version B1 or earlier, set switch 1
to ON and leave all other switches off.
DIP switch key:
ON = DIP switch in the up position
OFF = DIP switch in the down position
Refer to the following table for DIP switch 0 settings and the
following address switch table for DIP switch configuration
settings for ZONEX and ZONEX2.
Control panel DIP switch 0 setting
D7212B1
D8112
D9112B1
Leave switch 0 ON.

Smoke detector POPIT base Base POPIT addresses | en 9
Bosch Security Systems B.V. 2022.09 | 01 | F.01U.396.537
Control panel DIP switch 0 setting
D9412 Refer to 9000 Series
Operation and Installation
Guide
(P/N: 74-07692-000).
D9412G/D7412G/D7212G/
D7212GV2/D7212GV3
D7212GV4/D7412GV4/
D9412GV4
Refer to ZONEX and ZONEX 2
point address chart
B9512G B9512G-E/B8512G/
B8512G-E
Refer to ZONEX and ZONEX 2
point address chart
ZONEX 1 and ZONEX 2 point address chart
Address1Switch
ZX 1 ZX 2 B299 0 1 2 3 4 5 6
009 129 x00* ON ON ON ON ON ON ON
010 130 x01* ON ON ON ON ON ON
011 131 x02* ON ON ON ON ON ON
012 132 x03* ON ON ON ON ON
013 133 x04* ON ON ON ON ON ON
014 134 x05* ON ON ON ON ON
015 135 x06* ON ON ON ON ON
016 136 x07* ON ON ON ON
017 137 x08* ON ON ON ON ON ON
018 138 x09 ON ON ON ON ON
019 139 x10 ON ON ON ON ON
020 140 x11 ON ON ON ON

10 en | Base POPIT addresses Smoke detector POPIT base
2022.09 | 01 | F.01U.396.537 Bosch Security Systems B.V.
Address1Switch
ZX 1 ZX 2 B299 0 1 2 3 4 5 6
021 141 x12 ON ON ON ON ON
022 142 x13 ON ON ON ON
023 143 x14 ON ON ON ON
024 144 x15 ON ON ON
025 145 x16 ON ON ON ON ON ON
026 146 x17 ON ON ON ON ON
027 147 x18 ON ON ON ON ON
028 148 x19 ON ON ON ON
029 149 x20 ON ON ON ON ON
030 150 x21 ON ON ON ON
031 151 x22 ON ON ON ON
032 152 x23 ON ON ON
033 153 x24 ON ON ON ON ON
034 154 x25 ON ON ON ON
035 155 x26 ON ON ON ON
036 156 x27 ON ON ON
037 157 x28 ON ON ON ON
038 158 x29 ON ON ON
039 159 x30 ON ON ON
040 160 x31 ON ON
041 161 x32 ON ON ON ON ON ON
042 162 x33 ON ON ON ON ON