BOSER Technology HS-2616 User manual

HS-2616
HS-2616M
Intel® Pentium® M/Celeron®M/
ULV Intel® Celeron® M processor
Embedded Engine Board
•CompactFlash•Mini PCI•8-bit I/O•
•CRT/LVDS•Dual LAN•Audio•
•ATA/33/66/100•RS-232/485•
•USB2.0•PCI-104•WDT•
•Single +5V•H/W Monitor•

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e., electronic, mechanical, photocopying, recording)
of this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the contents of
this document without due notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2007 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.4, October 15, 2009

Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features....................................................................... 2
1.2 Specifications ........................................................................ 2
1.3 Board Dimensions................................................................. 4
Chapter 2 Unpacking ..................................................5
2.1 Opening the Delivery Package............................................. 5
2.2 Inspection............................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ................................................................. 7
3.2 Board Layout ......................................................................... 8
3.3 Jumper List ............................................................................ 9
3.4 Connector List ....................................................................... 9
3.5 Configuring the CPU ........................................................... 10
3.6 System Memory ................................................................... 10
3.7 VGA Controller .................................................................... 10
3.8 PCI E-IDE Drive Connector................................................. 12
3.9 Serial Port Connectors ....................................................... 13
3.10 Ethernet Connector............................................................. 14
3.11 USB Port............................................................................... 14
3.12 CMOS Data Clear................................................................. 15
3.13 Power and Fan Connectors................................................ 15
3.14 Keyboard/Mouse Connectors ............................................ 16
3.15 System Front Panel Control ............................................... 16
Connector JP1 Orientation .....................................................................................16
3.16 Watchdog Timer .................................................................. 17
3.17 Audio Connectors ............................................................... 18
3.18 CompactFlashConnector................................................ 18
3.19 IrDA Function....................................................................... 20
3.20 8-bit I/O Function................................................................. 20
3.21 PCI-104 Connector .............................................................. 24

Chapter 4 AMI BIOS Setup..................................... 27
4.1 Starting Setup...................................................................... 27
4.2 Using Setup ......................................................................... 28
4.3 Main Menu............................................................................ 29
4.4 Advanced Settings .............................................................. 30
4.5 Advanced PCI/PnP Settings............................................... 33
4.6 Boot Settings ....................................................................... 34
4.7 Security Settings ................................................................. 35
4.8 Advanced Chipset Settings................................................ 36
4.9 Exit Options ......................................................................... 37
Chapter 5 Software Utilities..................................... 39
5.1 IDE Driver Installation ......................................................... 39
5.2 VGA Driver Installation ....................................................... 43
5.3 LAN Driver Installation........................................................ 52
5.4 Audio Driver Installation..................................................... 65
5.5 USB2.0 Driver Installation .................................................. 68

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
 Do not remove boards or integrated circuits from their anti-static packaging
until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This helps to discharge any static
electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR clip
of the strap to the end of the shielded wire lead from a grounded object.
Please wear and connect the strap before handle the product to ensure
harmlessly discharge any static electricity through the strap.
 Please use an anti-static pad when putting down any components or parts or
tools outside the computer. You may also use an anti-static bag instead of
the pad. Please inquire from your local supplier for additional assistance in
finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTIONS.

1
Chapter 1
General Description
HS-2616 HS-2616M
The HS-2616 is an Intel® 852GME GMCH and HS-2616M is an Intel®
852GM GMCH chipset-based board designed. The HS-2616/
HS-2616M is ideal all-in-one embedded engine board. Additional
features include an enhanced I/O with CF, CRT/LVDS, dual LAN,
audio, 4 COM, and USB2.0 interfaces.
Its onboard ATA/33/66/100 to IDE drive interface architecture allows
the HS-2616/HS-2616M to support data transfers of 33, 66 or
100MB/sec. to one IDE drive connection. The HS-2616 supports Intel®
Pentium® M/Celeron® M processor, and HS-2616M supports ULV
Intel® Celeron® M processor 600MHz/512K.
The Intel® 852GM with 8MB shared main memory supporting CRT
display up to 1600 x 1200. It also supports 18-bit single/dual-channel
LVDS interface.
System memory is also sufficient with the one SO-DDR socket that can
support up to 1GB.
Additional onboard connectors include four USB2.0 ports providing
faster data transmission. And two external RJ-45 connectors for
10/100 Based Ethernet use.

2
To ensure the reliability in an unmanned or standalone system, the
watchdog timer (WDT) onboard HS-2616/HS-2616M is designed with
software that does not need the arithmetical functions of a real-time
clock chip. If any program causes unexpected halts to the system, the
onboard WDT will automatically reset the CPU or generate an interrupt
to resolve such condition.
1.1 Major Features
The HS-2616/HS-2616M comes with the following features:
 HS-2616 provides Intel® Pentium® M/Celeron® M processor
1.3~2.0GHz, supports 533/400MHz FSB
 HS-2616M provides ULV Intel® Celeron® M processor 600MHz/512K,
supports 400MHz FSB
 1 x SO-DIMM up to 1GB DDR SDRAM
 Intel® 852GM(E) GMCH/ICH4 system chipset
 Intel® 852GM(E) integrated VGA for CRT & LVDS
 2 x Intel® 10/100 Mbps ethernet
 AC’97 audio codec
 Supports CF, 2 x COM, 4 x USB2.0, PCI-104
 Supports 18-bit LVDS, 8-bit I/O, Single +5V power in, H/W Monitor
function
1.2 Specifications
 System
 CPU
HS-2616 provides
Intel® Pentium® M processor 760 2.0GHz
Intel® Pentium® M processor 745 1.8GHz
Intel® Celeron® M processor 370 1.5GHz
Intel® Celeron® M processor 320 1.3GHz
HS-2616M provides ULV Intel® Celeron® M processor 600MHz/512K
 Front Side Bus
533/400MHz FSB (HS-2616)
400MHz FSB (HS-2616M)
 BIOS
AMI PnP Flash BIOS
 System Chipset:
Intel® 852GME GMCH/ICH4 (HS-2616)
Intel® 852GM GMCH/ICH4 (HS-2616M)
 I/O Chipset
Winbond W83627HG

3
 System Memory
1 x 200-pin SO-DIMM socket up to 1GB DDR SDRAM
 Storage
1 x Type II CF socket
 Watchdog Timer
Software programmable time-out intervals from 1~255 sec. or 1~255
min.
 Hardware Monitor
Monitoring temperatures, voltages, and cooling fan status
 Expansion
PCI-104
 Power In
Single +5V power in
 Operating Temperature
0~+60 degrees C
 Operating Humidity
0~95%, non-condensing
 Board Size (L x W)
145 x 102 mm
 I/O Interface
 MIO
1 x RS-232
1 x RS-232/485
4 x USB2.0 (2 x internal, 2 x external)
1 x IDE
1 x PS/2 for KB/MS
 DI/O
8-bit input/output by parallel port
 Display
 Chipset
Intel® 852GME (HS-2616)
Intel® 852GM (HS-2616M)
 Display Memory
8MB shared main memory
 LVDS
18-bit single/dual-channel
 Resolution
CRT Mode: 1600 x 1200
 Audio
 Chipset
RealTek ALC202A
 Audio Interface (w/pin header)
MIC In, Line Out

4
 Ethernet
 Chipset
Intel® 82551QM and 82562ET dual 10/100 Mbps LAN
 Ethernet Interface
2 x RJ-45
1.3 Board Dimensions

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-2616/HS-2616M is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-2616/HS-2616M delivery
package contains the following items:
 HS-2616 or HS-2616M Board x 1
 Utility CD Disk x 1, including User’s Manual
 Cables (as following table)
 Jumper Bag x 1

6
Cables Package
NO. Description QTY.
1 1-to-2 Mini DIN cable 1
2 SPK 8-pin(2.0-pitch) phone jack x 2 1
3 COM DB9-10P (2.0-pitch) 1
4 40-pin to 44-pin IDE flat cable 1
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
Option Accessories
NO. Description
1 1-to-2 USB cable with bracket
2 Pentium® M Cooler (251-10310003G)

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-2616/HS-2616M. This chapter also contains information
related to jumper settings of switch, and watchdog timer selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (set JP7 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.

8
3.2 Board Layout
Top Side
Solder Side

9
3.3 Jumper List
Jumper Default Setting Setting Page
JP3 Onboard LAN 2 Enabled/Disabled Select:
Enabled Short 1-2 14
JP4 COM2 Use RS-232 or RS-485 Select: RS-232 Open 13
JP5 Short 3-4 10
JP10 System Frequency Select: 400MHz Short 10
JP7 Clear CMOS: Normal Operation Short 1-2 15
JP11 SDRAM Frequency Select: 266MHz Short 1-2 10
3.4 Connector List
Connector Definition Page
CN1 PCI-104 Connector 24
CN3/CN2 COM 1/COM 2 Connector (5x2 header) 13
CN4 Internal USB2.0 Port 14
CN5 IDE Connector 12
CN6 External Reset Button 16
CN7 External USB2.0 Port 14
CN8 RS-485 Connector 13
CN9 MIC In/Line Out Connector 18
CN10/CN11 RJ-45 Connector 14
CN12 PS/2 6-pin Mini DIN KB/MS Connector 16
CN13 15-pin CRT Connector 10
CN15/CN14 LVDS Panel Connector 10
CN16 IrDA Connector 20
CN17 SO-DDR Socket 10
CN18 CompactFlash Connector 18
FN1 Fan Power In Connector 15
JP1 System Front Panel Control 16
JP2 8-bit I/O Connector 20
JP6 Inverter Power In Connector 10
PW1 4-pin Power In Connector 15

10
3.5 Configuring the CPU
The HS-2616 provides Intel® Pentium® M processor 760 2.0GHz,
Pentium® M processor 745 1.8GHz, Celeron® M processor 370
1.5GHz, and Celeron® M processor 1.3GHz. The HS-2616M
embedded with ULV Intel® Celeron® M processor 600MHz/512K. If
you want to use 533MHz FSB processor, please set JP5/JP10, and
JP5/JP10 is only for HS-2616.
 JP5/JP10: System Frequency Select
Settings
Options JP5 JP10
400MHz FSB (default) Short 3-4 Short
533MHz FSB All Open Open
3.6 System Memory
The HS-2616/HS-2616M provides one SO-DDR socket at locations
CN17. The maximum capacity of the onboard memory is 1GB.
NOTE: If System Frequency sets 400MHz FSB, please use 266MHz SDRAM
 JP11: SDRAM Frequency Select
Options Settings
333MHz FSB Open
266MHz FSB (default) Short
2
1
3.7 VGA Controller
The HS-2616/HS-2616M provides two connection methods of a VGA
device. CN13 offers a single standard CRT connector and CN15/CN14
are the LVDS interface connectors onboard reserved for flat panel
installation.

11
 CN13: CRT Connector
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 N/C 10 GND
11 N/C 12 SDA
13 HSYNC 14 VSYNC
15 SCL
1
515
10
611
 CN15/CN14: LVDS Interface Connector
PIN Description PIN Description
1 VLCD 2 VLCD
3 GND 4 GND
5 A0-/A4- 6 A0+/A4+
7 A1-/A5- 8 A1+/A5+
9 A2-/A6- 10 A2+/A6+
11 CLK1-/CLK2- 12 CLK1+/CLK2+
13 N/C 14 N/C
12
13 14
NOTE: LVDS cable should be produced very carefully. A0- & A0+ have to
be fabricated in twister pair (A1- & A1+, A2- & A2+ and so on)
otherwise the signal won’t be stable.
NOTE: If use CN15 only, it just supports 18-bit single channel LVDS
panel; If you want to use 36-bit dual channel LVDS panel, please
use CN15 and CN14 combined.
 JP6: Inverter Power In Connector
PIN Description
1 +12V
2 +12V
3 VCC5
4 BK_EN
5 LCD_EN
6 GND
1
6

12
3.8 PCI E-IDE Drive Connector
CN5 is a standard 44-pin 2.0-pitch connector daisy-chain driver
connector serves the PCI E-IDE drive provisions onboard the HS-2616/
HS-2616M. A maximum of two ATA/33/66/100 IDE drives can be
connected to the HS-2616/HS-2616M via CN5.
 CN5: IDE Connector
PIN Description PIN Description
1 Reset 2 GND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GND 20 N/C
21 PDREQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 PIORDY 28 PR1PD1-
29 RPDACK- 30 GND
31 Interrupt 32 N/C
33 RPDA1- 34 PATA66
35 RPDA0- 36 RPDA2-
37 RPCS1- 38 RPCS3-
39 HDD Active 40 GND
41 VCC 42 VCC
43 GND 44 N/C
1
2
43
44

13
3.9 Serial Port Connectors
The HS-2616/HS-2616M offers NS16C550 compatible UARTs
with Read/ Receive 16-byte FIFO serial ports and internal 10-pin
headers and RS-422/485 connector.
 CN3/CN2: COM 1/COM 2 Connector (5x2 Header)
PIN Description PIN Description
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 N/C
19
10 2
 CN8: RS-485 Connector (3x2 Header, COM4)
PIN Description PIN Description
1 TX- 2 TX+
3 RX+ 4 RX-
5 GND 6 VCC
15
62
NOTE: The terminal resistance of RX & TX is set at 180 Ω .
 JP4: COM 2 use RS-232 or RS-485 Select
Options Settings
RS-232 (default) Open
RS-485 by Auto (*1) Short 1-2, 3-4, 5-7, 8-10
RS-485 by –RTS (*-1) Short 1-2, 3-4, 7-9, 8-10
RS-485 Full Duplex (*2) Short 1-2, 3-4, 6-8
19
10 2
NOTE: *1: 2-wires RS-485 function
*2: 4-wires point-to-point full duplex function
4-wires point-to-point full duplex RS-485

14
Typical RS-485 2-wires Mutildrop Network
3.10 Ethernet Connector
The HS-2616/HS-2616M provides two external RJ-45 interface
connectors. Please refer to the following for its pin information.
 CN10/CN11: RJ-45 Connector
PIN Description
1 TX+
2 TX-
3 RX+
4 R/C GND
5 R/C GND
6 RX-
7 R/C GND
8 R/C GND
1
8
 JP3: Onboard LAN 2 Enabled/Disabled Select
Options Settings
Enabled (default) Short 1-2
Disabled Short 2-3
1
3
3.11 USB Port
The HS-2616/HS-2616M provides one 8-pin connectors, at location
CN4, for two USB ports, and four external USB2.0 ports at CN7.
 CN7: External USB2.0 Port
PIN Description PIN Description
1 VCC 2 VCC
3 USBD0- 4 USBD1-
5 USBD0+ 6 USBD1+
7 GND 8 GND