Boss Audio Systems DVD-3800T User manual

2
Compatible with PAL DVD (Video CD)
and NTSC DVD (Video CD)
This player can play discs recorded in
either PAL or NTSC format.
• A single LSI chip now integrates all
major DVD playback circuit functions
including MPEG2 decoder, video D/A
converter, and audio decoders.
• L/R stereo analog audio outputs for
connection to existing head unit aux
inputs. Video output is composite
video.
• Supplied remote handles multi-
function software (multi-language
audio-track/subtitle, multi-angle,multi-
story, etc.), plus all basic functions.
USE THIS PRODUCT SAFELY
Do not expose the product to water or
excessive moisture. This could cause
electrical shorts, fire or other damage.
When Driving
Keep the volume level low enough to be
aware of road and traffic conditions.
When Parked
Parking in direct sunlight can produce
very high temperatures inside your
vehicle. Give the interior a chance to
cool down before starting playback.
Use the Proper Power Supply
This product is designed to operate with
a 12 volt DC, negative ground battery
system (the regular system in a North
American car).
Protect the Disc Mechanism
Avoid inserting any foreign objects into
the slot of this player.
Failure to observe this may cause
malfunction due to the precise
mechanism of this unit.
Use Authorized Service Centers
Do not attempt to disassemble or adjust
this precision product. Please refer to
the Service Center list included with this
product for service assistance.
For Installation
The unit should be installed in a
horizontal position with the front end up
at a convenient angle, but not more than
30˚.
FEATURES

3
CONTENTS
Safety Information ........................................................................................4
Disc Notes .....................................................................................................5
The Player......................................................................................................6
Front View ...............................................................................................................6
Back View ...............................................................................................................7
Installation .....................................................................................................8
Electric Connection ....................................................................................11
Remote Control...........................................................................................12
Location and Function of Keys.............................................................................12
Preparing the Remote Control..............................................................................14
General Operation.......................................................................................15
Turn the Unit On....................................................................................................15
Basic Play .............................................................................................................15
DVD Video Menu Play...........................................................................................16
Mode Selection.....................................................................................................16
Reset Function......................................................................................................16
Last Play Memory .................................................................................................16
Advanced Operation...................................................................................16
Repeat Play/ Paragraph Repeat Play ...................................................................16
PBC Menu Playback of VCD/SVCD .....................................................................16
On-screen Display Function .................................................................................17
PAL/NTSC System Selection................................................................................18
Bookmark Function ..............................................................................................18
Random Playing....................................................................................................18
Zoom Function......................................................................................................19
Special Function for DVD .....................................................................................19
Special Function for VCD .....................................................................................20
Data Disc and Audio CD Play Operation ..............................................................20
Setup ............................................................................................................22
Language Setup ...................................................................................................22
Display Setup........................................................................................................23
Audio Setup ..........................................................................................................23
Lock Setup............................................................................................................24
Others Setup.........................................................................................................25
TV Operation ...............................................................................................25
Trouble Shooting.........................................................................................26
Specifications..............................................................................................27

4
CAUTION:
MOBILE DVD PLAYER IS A CLASS I
LASER PRODUCT. HOWEVER THIS
MOBILE DVD PLAYER USES A
VISIBLE/INVISIBLE LASER BEAM
WHICH COULD CAUSE HAZARDOUS
RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE MOBILE
DVD PLAYER CORRECTLY AS
INSTRUCTED.
USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND - DO NOT
REPAIR YOURSELF. REFER SERVICING
TO QUALIFIED PERSONNEL.
WARNING:
•TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR
MOISTURE.
•TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE
RECOMMENDED ACCESSORIES.
•THIS DEVICE IS INTENDED FOR
CONTINUOUS OPERATION.
This product incorporates copyright
protection technology that is protected
by method claims of certain U.S. patents
and other intellectual property rights
owned by Macrovision Corporation and
other rights owners. Use of this
copyright protection technology must be
authorized by Macrovision Corporation,
and is intended for home and other
limited viewing uses only unless
otherwise authorized by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.
SAFETY INFORMATION
Region Management Information
Region Management Information:
This Mobile DVD Player is designed and
manufactured to respond to the Region
Management Information that is recorded
on a DVD disc. If the Region number
described on the DVD disc does not
correspond to the Region number of this
Mobile DVD Player, this Mobile DVD
Player cannot play this disc.

DISC NOTES
5
Disc formats supported by this player
DVD
12 cm disc
Video CD
12 cm disc
CD
12 cm disc
MP3
12 cm disc
Discs which cannot be played with this
player
•DVD-ROM
•DVD-R/DVD-RAM
•CDV
•CD-G
Handling and Cleaning
•Dirt, dust, scratches and warping disc
will cause misoperation.
•Do not place stickers or make
scratches on discs.
•Do not warp discs.
•A disc should always be kept in its
case when not in use to prevent from
damage.
•Do not place discs in the following
places:
1. Direct sunlight
2. Dirty, dusty and damp areas
3. Near car heaters
4. On the seats or dashboard
Disc Cleaning
Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Note:
A disc may become somewhat scratched
(although not enough to make it
unusable) depending on your handling
and conditions in the usage environment.
Note these scratches are not an
indication of any problem with the player.
Preparing New Discs with Rough
Spots
A new disc may have rough edges on its
inside and outside edges. If a disc with
rough edges is used, the proper setting
will not be performed and the player will
not play the disc. Therefore, remove the
rough edges in advance by using a ball
point pen or pencil as shown on the right.
To remove the rough edges, press the
side of the pen or pencil against the
inside and outside edges of the disc.
Rough spots
on inside edge
Ball point pen
or pencil
Rough spots on
outside edge
Label side up
Do not touch
the underside
of the disc
Do not bend
Wipe the disc from center
toward the outside edge

6
THE PLAYER
FRONT VIEW
1. (POWER BUTTON)
2. (EJECT BUTTON)
3. SETUP
4. MENU/TV SEARCH
5. SOURCE
6. DISC SLOT
7. PLAY/PAUSE ( )
8. STOP ( )
9. PREV / CH- ( )
10. NEXT / CH+ ( )
11. VOLUME
12. VOLUME
13. / , / cursor buttons
14. ENTER
15. Indicator Light for DVD
16. Indicator Light for TV
17. Indicator Light for AV
18. VIDEO IN
19. AUDIO IN L
20. AUDIO IN R
21. IR
22. RESET BUTTON
1821322 20171615 14 19
2410135 8 7 9 61 11 12

7
THE PLAYER
BACK VIEW
23. DC 12V INPUT Socket
24. DC 12V OUTPUT Socket
25. DIGITAL AUDIO
26. REMOTE Socket
27. S-VIDEO Socket
28. AUDIO/VIDEO OUTPUT 1
29. AUDIO/VIDEO OUTPUT 2
30. DIVERSITY ANTENNA INPUT
2829272625242330

8
Notes:
•Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
•Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected properly
and the unit and the system work
properly.
•Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
•Consult with your nearest dealer if
installation requires drilling holes or
other modifications of the vehicle.
•Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.
•If installation angle exceeds 30˚from
horizontal, the unit might not give its
optimum performance.
•Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front”(conventional DIN Front-
mount) or “Rear”(DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
30˚
TAKE OUT SCREW BEFORE
INSTALLATION
Before install the unit, please remove the
two screws.
DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be installed in any dashboard
having an opening as shown below:
Installing the unit
Be sure you test all connections first, and
then follow these steps to install the unit.
1. Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's positive (+) terminal.
2. Disconnect the wire harness and the
antenna.
3. Lift the top of the outer trim ring then
pull it out to remove it.
4. The two supplied keys release the tabs
inside the unit's sleeve so you can
remove it. Insert the keys as far as they
will go (with the notches facing up) into
the appropriate slots at the middle left
and right sides of the unit. Then slide
the sleeve off the back of the unit.
182 mm
53 mm
Take out screw before installation
INSTALLATION

9
5. Mount the sleeve by inserting the sleeve
into the opening of the dashboard and
bend open the tabs located around the
sleeve with a screwdriver. Not all tabs
will be able to make contact, so
examine which ones will be most
effective. Bending open the appropriate
tabs behind the dashboard to secure
the sleeve in place.
6. Reconnect the wire harness and the
antenna and be careful not to pinch
any wires or cables.
7. Slide the unit into the sleeve until it
locks into place.
8. To further secure the unit, use the
supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap
to the mounting bolt on the back of
the unit. If necessary, bend the metal
strap to fit your vehicle's mounting
area. Then use the supplied hardware
(Tapping Screw (5x25mm) and Plain
Washer) to attach the other end of
metal strap to a solid metal part of the
vehicle under the dashboard. This strap
also helps ensure proper
electricalgrounding of the unit.
Outer Trim Ring
L Key
Sleeve
R Key
Sleeve
Dashboard
Screwdriver
Tabs
9. Reconnect the cable to the vehicle
battery's negative (-) terminal. Then
replace the outer trim ring .
Removing the unit
1. Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's negative (-)
terminal.
2. Remove the metal strap attached the
back of the unit (if attached).
3. Lift the top of the outer trim ring then
pull it out to remove it.
4. Insert both of the supplied keys into
the slots at the middle left and right
sides of the unit, then pull the unit out
of the dashboard.
Spring Washer
Tapping Screw
Plain Washer
Hex Nut
Metal Strap
Mounting Bolt
INSTALLATION

10
Dashboard or
Console
Side view showing
Screw Holes marked T, N or S
Factory Radio
Mounting
Bracket
Hook
Screw
Screw
Hook
DIN REAR-MOUNT (Method B)
If your vehicle is a Nissan, Toyota or
Suzuki, follow these mounting instructions.
Use the screw holes marked T (Toyota),
N (Nissan) or S (Suzuki) located on both
sides of the unit to fasten the unit to the
factory radio mounting brackets supplied
with your vehicle.
To fasten the unit to the factory radio
mounting brackets.
1. Use a screwdriver to loose the hook's
screws on the front left and right sides
of the unit and remove the hooks.
2. Align the screw holes on the bracket
with the screw holes on the unit, and
then tighten the screws on each side.
3. Fasten with the supplied truss screws
(5x5mm) or flush surface screws
(4x5mm), depending on the shape of
the screw holes in the bracket.
Note: the outer trim ring, sleeve and the
metal strap are not used for method B
installation.
INSTALLATION