BPE Amstel Dock User manual

BPE Amstel Dock
User Manual

1. Safety Information....................................................................1
1.1. Important safety instructions.....................................1
2. Speci ication...............................................................................2
2.1. Datasheet......................................................................2
3.Preparation for Installation.....................................................3
3.1. Installation requirements............................................3
3.2. Electrical Wiring Diagram............................................4
3.2.1. 230V Single Phase.........................................4
3.3. Installation Considerations.........................................4
4.In the Box.....................................................................................5
5.Installation Instructions...........................................................6
5.1. Step-by-Step Installation Instructions for:................6
7.Maintenance Instructions........................................................7
7.1. Product Servicing..........................................................7
7.2. Warranty Description...................................................7
7.3. Safety Notice.................................................................7
User Manual Contents......................................................1

• Read this entire document before installing the Amstel Dock.
• Keep children away from the Amstel Dock.
• The Amstel Dock must be grounded through a permanent wiring
system or an equipment grounding conductor.
•Donotinstallthemountingbracketnearflammable,explosive,harsh,
orcombustiblematerials,chemicals,orvapours.
• Never spray water or any other liquid directly at the wall mounted
Amstel Dock.
•Donotusethe Amstel Dockifitisdefective,appearscracked,frayed,
broken,orotherwisedamaged.
•Donotattempttodisassemble,repair,tamperwith,ormodifythe
Amstel Dock yourself. Any maintenance must be performed by
authorised technical personnel or our company’s technical support.
Contact us for anyrepairsormodification.
• Handle with care when transporting the Amstel Dock. Do not subject
ittostrongforce,impactorpull,twist,tangle,drag,orsteponthe
Amstel Dock to prevent it or any components from damage.
1.1. Important Safety Instructions
This document contains important instructions and warnings that
must be followed for both installation and maintenance of the
Amstel Dock.
1. Safety Information
WARNING
1

2.1 Datasheet
2. Specication
2

Installation of the EV Charger requires that you:
•Calculatetheexistingelectricalloadtodeterminethe
maximumoperatingcurrent.
• Calculate the distance to ensure minimal voltage drop.
• Obtain any necessary permits from the local authority that has
jurisdictionandconrmthatthefollow-upinspectionhasbeen
scheduled by an electrician after the installation is complete.
• Use only copper conductors.
• Use conductors that are sized in accordance with local wiring
regulations. The selected cable must be able to sustain periods
of constant load of up to 40A.
• Use protective devices. The circuit protection device chosen
must incorporate a suitable residual-current device (RCD)
and over-current protection in relation to the electrical load
selected.
Choose the Best Location for the EV Charger:
• Determine the parking location of the vehicle to ensure that
the charge cable will reach the charge port.
• Determine the parking location of the vehicle to ensure
that the current charge cable reaches the charge port in an
enclosedgarage,typicallyonthevehicle’schargeportside.
•Inawell-ventilatedarea.Avoidinstallationinanenclosedbox,
or adjacent to hot appliances.
• 1.2m above the ground.
•190mmfromanyobstacletoallowcablecollected.
Note:
The Amstel Dock is approved for outdoor use. Protection from
rain is recommended but not required.
3. Preparation for Installation
3.1. Installation Requirements
3

3.2. Electrical Wiring
3.2.1. 230V Single-Phase
The L,N and PE should be wired according to local requirements.
The phase used must measure 230V (±10%).
• WARNING: Each ground must be connected to neutral
atonlyonepoint,ortheEVchargercannotoperate.
• WARNING:BeforeinstallingtheAmstel Dock,identify
the type of utility service connection available on site. If
you are unsure about the type of connection available
at theservicepanel,consultanelectricianfor
assistance.
3.3. Installation Considerations
Three configurations are available to install the Amstel Dock:
The location of the conduit determines which installation method to
follow.Iftheconduitrunsalongtheoororlowtothewall,usethe
bottomentryconguration.Iftheconduitcomesfrominsidethe
wall,usetherearentryconguration.Iftheavailableconduitcomes
fromtheceiling,usethetopentryinstallation.
Note: Throughoutthemanual,“conduit”isusedasthestandard
term for the protective tubing that houses the service wiring. In
regionswhereconduitisnotused(Europeforexample),acable
comprised of service wiring enclosed in a protective jacket may be
substituted for conduit if allowed by local regulations.
Here are some additional guidelines:
• Conduit openings are sized for 32mm conduit.
• Conduitneedstobemetalandameretardant.
• Use an appropriate circuit breaker.
• Tokeepthehousingwaterproof,usecableglands.
4

4. In The Box
1234
5 6
NO. Item Quantity
1Amstel Dock - Front Cover 1
2Amstel Dock - Back Box 1
332mm cable gland 1
4Mounting Template 1
58 x 40mm anchoring screw 1
6 M6*8 Screws 4
5

5.1. Mounting the Amstel Dock
Step 1
Position
Position the template on
the wall where you wish to
install the EV Charger.
The picture shows
the distances we
recommend.
At a minimum of 120cm
fromfloorlevel.
Drilling pilot holes.
Drill two holes according
to the instruction on the
position template.
Step 2
Insert the 8*40 Flat head
screwsintotheholes,and
use the screw driver to
makethe2pcs8*40at
head screws anchor the
wireboxontothewall.
>0.5M
>1.2M
Wall
Drill
Side of wall
Floor level
Two points on the
top and bottom of
position plate
Screwdriver
Wirebox
8*40 Flat head
screws
Note: Hooks and socket are not
included. For reference only.
6
5. Installation Instructions

In order to ensure the normal service life of the Amstel Dock and
reducetheriskduringits life,itmustbeservicedwithinthe
specifiedtime period; the service of the equipment should be
carried out by professionals,andqualifiedandcorrecttools
shouldbeused.
7.1. Product Servicing
• Regularly check whether the product is damaged.
•Ensurethatthecircuitbreakerdedicated for the Amstel Dock is
switched off at the consumer unit
•Ifagroundfaultoccurs,firstmakesurethatthegroundingcable
carriesvoltage,andthencheckthatthereisnohighvoltagein
thesystem,andthenrepairtheAmstel Dock.
7.2. Warranty Description
• BPE Amstel Dock has a 5year warranty.
• Ensure that the Amstel Dock has undergone proper installation.
Duringthewarrantyperiod,ifquality problemsoccurunder
normaluse,thecompanywillprovidea replacement.
•Theuser’simproperhandling,installation,incorrectuseand
maintenance,negligenceornaturaldamagetotheproductand
failure of normal use are not covered by the warranty.
7.3. Safety Notice
Operation and maintenance risk notication
• Do not disassemble the Amstel Dock while it has power
connected, otherwiseitmaycausefireandelectric shock
accidents.
•Intheeventthe Amstel Dock gets damaged,theremaybea
riskofelectric shock. Ensure that the power is switched off
before carrying out any maintenance.
7. Maintenance Instructions
8
• Do not disassemble or modify charging facilities and wiring
withoutauthorisation,otherwiseitmaycausefireandelectric
shock accidents.