Bradley Aerada 900 Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
Aerada™ 900 Series
With Accu-Zone®(AZ) Infrared Control
Table of Contents
Supplies Required ...............................2
Dimensions and Configurations.....................2
Installation .....................................3
Multi-Faucet Wiring ..............................4
Replacing the Sensor ............................5
Troubleshooting .................................5
S53-341TL - 4" Centerset
S53-341TMA - 4" Centerset w/ TMV
S53-343TL - Centershank
S53-343TMA - Centershank w/TMV
S53-345TL - 4" Centershank w/8" Trim Plate
S53-345TMA - 4" Centershank w/ 8" Trim Plate, TMV
WARNING
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
CAUTION
A DC plug-in adapter (supplied by Bradley) should be used in conjunction with the 900 Series Futura (AZ)
Faucets. The DC plug-in adapter supplied by Bradley is 12V DC regulated. Direct connection to 120V/220V
50/60Hz could result in personal injury and will damage the sensor.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file
this manual with the owner or maintenance department. Compliance and conformity to local codes and
ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
When the faucet is mounted on a fixture with a stainless steel bowl, it is recommended that the bowl have a
satin finish rather than a mirrored or highly polished finish.
Product warranties may be found under “Products” on our web site at bradleycorp.com.
215-1680 Rev. D; ECN 16-02-004
© 2016 Bradley
Page 1 of 6 11/18/2016

2
Aerada 900 Series Faucet Installation
11/18/2016 Bradley • 215-1680 Rev. D; ECN 16-02-004
Supplies Required
• 120V/220V 50/60Hz power source using Bradley supplied 120VAC/12V DC plug-in adapter
• Tempered hot and cold supply piping and fittings to solenoid valve (1/2" NPT)
• 1/4" O.D. tubing
• Pipe fittings, pipe sealant as required
Dimensional Information
Centershank Mounting Centerset Mounting
7"
(178)
4"
(102)
Washer
3/4" (19)
Drilled Hole
Copper Tubing
Nut
3/8" (10)
Drilled Hole
1-1/8" (29)
Drilled Hole
Nut &
Washer
Faucet Stud
Copper Tubing
8"
(203)
1-1/8"
(29)
Flow Control
Aerator Assy.
(S05-142A)
Adapter
(153-467)
Sensor
Window
(269-604)
Accu-Zone Sensor
Fitting Assy.
(S05-193)
Faucet Components
Centershank
Faucet Shown
1
2
34
5
6
7
8
9
10
1
2
4
6
7
8
8
9
9
Mounting Configurations
Centerset Mounting
Ref. Part No. Description
1 110-115 Mounting Nut
2 112-002CB Mounting Washer
3 161-151 8" Trimplate
Mounting Screw
4 S27-224 Mounting Prepack
5 159-399 8" Trimplate
6 161-078
Sensor Bracket Nut
7 142-002BS Sensor Bracket
Washer
8 - Sensor Bracket
9 269-1184-DC Accu-Zone Sensor
10 160-169 Sensor Mounting
Screw
Centershank Mounting
Parts List
2-5/16"
(58)
(mm)

3
Installation Aerada 900 Series Faucet
Bradley • 215-1680 Rev. D; ECN 16-02-004 11/18/2016
Cold Inlet
1/2" NPT
Hot Inlet
1/2" NPT
1/4" O.D. Tubing
(Supplied by Installer)
(30" max. length, IPC,
section 604.5; UPC,
section 604.12)
Solenoid
Valve
TMA Navigator®
Shown
Centershank
Faucet Shown
Mount Faucet on Deck
Deck
Centerset
Faucet
Shown
Washer
Nut
1
ADrill holes in deck to the size and position
for your faucet configuration, as shown on
previous page.
BAttach faucet and trim plate (if applicable)
securely to deck. Seal around faucet and
trim plate with plumber's putty.
Connect Water and Electrical Supply
2
120VAC/12V DC
Plug-In Adapter
For units equipped with a TMA Navigator
Mixing Valve, complete steps 3 and 4 of this
installation manual.
Connect Faucet Harness
Connector to Mating
Connector on Solenoid Valve

4
Aerada 900 Series Faucet Installation
11/18/2016 Bradley • 215-1680 Rev. D; ECN 16-02-004
Multi-Faucet Wiring
One plug-in adapter operates up to four
faucets at one time. Additional plug-in
adapter(s) are required for installations
with more than four faucets.
H
C
DO NOT SKIP THIS STEP!!!
This valve is NOT factory preset. Upon installation, the temperature of this valve must be checked and adjusted
to ensure delivery of a safe water temperature. Water in excess of 110°F (43°C) may cause scalding.
This step only applies for units equipped with a TMA Navigator Mixing Valve.
Adjust Temperature with Running Water
3
ALoosen cap screw about 1/4" (4-6 turns)
and lift up cover (do not remove).
B
Using cover, turn cartridge gently until
desired water temperature is reached. Do
not turn past stops as this may damage
unit. Push cover down and tighten screw.
Test Unit
4
This step only applies for units equipped with a TMA Navigator Mixing Valve.
A
Shut the hot water inlet off by closing
hot water inlet valve. While the hot water
supply is turned off, check to make sure
the cold water flow is reduced. If the cold
water is reduced properly, reopen the hot
water supply.
B
Shut the cold water inlet off by closing
the cold water inlet valve. While the cold
water supply is off, check to make sure
that the hot water flow has shut down.

5
Installation Aerada 900 Series Faucet
Bradley • 215-1680 Rev. D; ECN 16-02-004 11/18/2016
Replacing the Sensor CAUTION To avoid personal injury and/or damage to the faucet,
TURN OFF the electrical power and water BEFORE
beginning any cleaning, troubleshooting or maintenance.
NOTICE! Sensor must be flush and parallel with the lens.
Do not force or bend the bracket!
Troubleshooting – Solenoid Valve
Problem Cause Solution
Faucet fails to shut off and drips. The cartridge valve is defective. Replace cartridge.
Faucet fails to turn on. A failed valve or loose electrical
connection to the connectors.
1. Repair loose connection.
2. If possible, determine whether sensor, power adapter
or valve is defective by swapping parts with an adjacent
faucet. Replace defective part.
Ref. Part No. Description
1 118-334 Valve Body
2 S27-352 Cartridge
3 125-165 O-Ring, #2-013
4* 125-160 Flow Restrictor, .5 GPM
Parts List for S07-068-DC
Centerset Mounting
Centershank Mounting
Accu-Zone
Sensor
Bracket
* Not included with S07-068-DC.
S07-068-DC
A
Disconnect the faucet harness
connector from the solenoid
valve and remove the faucet from
the deck.
B
Following the illustrations at right
for your faucet configuration,
remove the screws and /or
nuts holding the bracket, then
carefully remove the bracket and
sensor assembly from the faucet
shell.
C
Remove screws securing the
existing sensor to bracket.
Installation of the new sensor is
the reverse process.
1
2
3
4

6
Aerada 900 Series Faucet Installation
11/18/2016 Bradley • 215-1680 Rev. D; ECN 16-02-004
Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions:
• If stop valves are used, make sure that they are fully open.
• Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-
connections or leaking stop valves.
• Check the hot water heater output to make sure that it is at least 10° F above the set temperature.
Troubleshooting – Thermostatic Mixing Valve
Close the appropriate shut-off valves prior to disassembly and reopen valves after inspection and
repair is complete.
Problem Cause Solution
External leaks. Damaged cartridge or
O-rings.
Replace cartridge with part number 269-1927
Improper water temperature or
temperature fluctuation.
Hot water supply is not 10°
above desired set point.
Increase hot water supply temperature
Valve temperature is not
properly set.
Adjust the temperature as shown on page 4 step 3.
Limited water flow. Dirt and debris have built
up in the valve or strainer.
1. Check to make sure both hot and cold supplies are connected to the
Navigator mixing valve and that they have water flow.
2. Remove cover and U-clip. Remove the cartridge and clean the
strainer. It is not required to grease cartridge, however if desired, use
silicone grease only.
Do not use grease on check valves.
Ref. Part No. Description
1 160-463 Cap Screw
2 107-582 Cover
3 269-1927 Thermostatic Cartridge
4 198-014 Check Valve*
5 132-051 Retaining Ring*
6 146-079 U-Clip
7 118-319 Valve Body
* Included with Prepack S65-326
1
3
2
7
45
6Strainer
173-028
Tempered Line Adapter Option:
Part no. S39-804
Parts List for S01-526
S01-526