Bradley S19-110SS User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
215-145SS Rev. H; ECN 08-517
© 2008 Bradley Corporation
Page 1 of 5 8/11/08
S19-110SS
Free-Standing Drench Shower
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . 2
Installation Instructions. . . . . . . . . . . . . . . . . . 3
Assembly of Components . . . . . . . . . . . . . . . 4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2
S19-110SS Installation
8/11/08 Bradley Corporation • 215-145SS Rev. H; ECN 08-517
IMPORTANT
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to the
eyewash should be “ON” at all times. Provisions shall be made to prevent unauthorized
shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per ANSI
Z358.1.
The inspection and testing results of this equipment should be recorded weekly to verify
proper operation. This equipment should be inspected annually to ensure compliance
with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment per ANSI
Z358.1.
For questions regarding the operation or installation of this product, visit www.
bradleycorp.com or call 1-800-BRADLEY.
Product warranties and parts information may also be found under ”Products” on our
web site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
P.O.Box309,MenomoneeFalls,WI53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetriebprüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051

3
Installation S19-110SS
Bradley Corporation • 215-145SS Rev. H; ECN 08-517 8/11/08
Installation
Supplies Required:
• (3) 3/8" floor anchors and bolts
• Pipe sealant
• Piping to 1-1/4" NPT water supply inlet on unit
• Adequate supply pipe supports
• Min. 4" drain to accommodate 30 gallons per minute
discharge for shower waste
• OPTIONAL: sign-mounting hardware
Step 1: Secure base to floor
1. Install three suitable anchors (supplied by installer)
for 3/8" bolts in the floor.
2. Bolt the base to the floor anchors using 3/8" bolts
(supplied by installer).
Step 2: Assemble components
1. Assemble the remaining unit components as
shown on page 4.
• Apply pipe sealant (by installer) to all male-
threaded pipe joints.
• Use the rubber grip pad provided or a strap
wrench around pipes when tightening to prevent
marring. Place the grip pad on the pipe, then
put the wrench over the grip pad and turn the
pipe with the wrench.
• Bottom edge of showerhead should be 7'-0"
(2134mm) from floor.
Step 3: Connect water supply
IMPORTANT: Do not rely on Bradley’s
Combination Unit to support supply piping.
1. Connect water supply piping to 1-1/4" NPT inlet
on unit (piping by installer). Provide adequate
supports (by installer) for supply pipe using pipe
hangers or other means.
2. Hang the safety sign from the unit with the curtain
hooks provided (or mount it to the wall using sign-
mounting hardware by installer).
3. Open water supply lines. Test for leaks and
adequate water flow.
NOTE: All dimensions assume standard thread
engagement. Variations in manufacturing allow for
+/- 1/8" (3mm) per threaded joint. To find the tolerance
of a dimension, add the number of thread joints in
between a dimension and multiply it by 1/8" (3mm).
Ø9" (229mm) Flange with
(3) Ø3/8" (10mm) Holes on
Ø8" (203mm) Bolt Circle
9"
(229mm)
26-1/2"
(673mm)
7'-0"
(2134mm)
to Floor
24"
(610mm)
3.7"
(94mm)
41-1/2"
(1054mm)

4
S19-110SS Installation
8/11/08 Bradley Corporation • 215-145SS Rev. H; ECN 08-517
Assembly of Components
P.O.Box 309, Menomonee Falls,WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift.Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signe en bas.S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O.BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-050
16 16.1
17
18
1
2
3
4
5
5
7
8
9
13
10
14
15
12.1
11
6
12.2 12.11
12
2
1-1/4" NPT
Supply Inlet
1-1/4" NPT
Supply Inlet
NOTE: If tee
(upper Item 5) is
used as the supply
inlet, then relocate
coupling (Item 4) to
this location.
NOTE: Items 12.1–12.2 come preassembled as Item 12.

5
Installation S19-110SS
Bradley Corporation • 215-145SS Rev. H; ECN 08-517 8/11/08
Parts List
1 131-062 1 Base
2 269-1048 2 Coupling
3 113-1182 1 Pipe, Stainless Steel 1-1/4" NPT x 32"
4 169-1066 1 Pipe Plug Coupling
5 269-237 2 Tee 1-1/4" NPT
6 113-541 1 Pipe 1-1/4" NPT x 19"
7 113-583 1 Pipe, Stainless Steel 1-1/4" NPT x 22"
8 269-238 1 Sq. Head Pipe Plug 1-1/4" NPT
9 269-236 1 Reducing Bushing
10 151-001 2 Curtain Hook
11 113-006NX 1 Pipe 1" NPT x 9"
12 S30-061 1 Ball Valve Assembly
12.1 S27-276 1 Ball Valve 1" with Jam Nut
12.11 161-079 1 Jam Nut only
12.2 128-142 1 Handle
13 128-156A 1 Pull Rod 24" Long
14 113-006MN 1 Pipe 1" NPT x 12"
15 169-1074 1 90° Elbow 1" NPT
16 S24-191 1 Stainless Steel Showerhead Assembly
16.1 S24-187 1 Flow Control Assembly, 23 GPM
17 114-050 1 Safety Sign
18 204-421 1 Emergency Inspection Tag
19 269-915 1 Grip Pad (not shown)
Item Part No. Qty Description Item Part No. Qty Description