Bradley Terreon TDB3103 User manual

Installation
Instructions
TDB3103
Terreon®36" Semi-Circular
Deep Bowl Washfountain with Air
Metering Control
WF3203
Terreon®Extra Height 36" Semi-
Circular Classic Washfountain with
9" Deep Bowl and Air Metering
Control
215-1479 Rev. A; EN 02-089
Page 1 of 24
P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
Main water supply to the unit
should be ON at all times.
This installation manual and parts
list should be filed by the owner’s
maintenance department.
IMPORTANT
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . . . 2
Model TDB3103 Washfountain Dimensions . . . . 3
Model WF3203 Washfountain Dimensions . . . . . 4
Washfountain Rough-Ins . . . . . . . . . . . . . . . . . . 5-7
Installation Instructions . . . . . . . . . . . . . . . . . . .7-12
Air Valve Troubleshooting . . . . . . . . . . . . . . . . . .13
Terreon® Cleaning/Maintenance . . . . . . . . . . . . .14
Gel-Coated Fiberglass Cleaning/Maintenance . . .14
Stainless Steel Cleaning/Maintenance . . . . . . . . .15
Soap Dispensing Valve Repair Parts . . . . . . . .16-17
Soap Recommendations and Maintenance . . . . . .18
Sprayhead Troubleshooting/Repair Parts . . . . . . 19
Manual Mixing Valve Repair Parts . . . . . . . . . . .20
Angle Volume Control Valve Repair Parts . . . . . .21
Actuator Module Assembly Components . . . . . .22
Metering Air Valve Maintenance . . . . . . . . . . . . .23
Vernatherm™ Mixing Valve Maintenance . . . . . .24
TDB3103
WF3203

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
TDB3103, WF3203 Installation Instructions
Bradley Corporation • 215-1479 Rev. A; EN 02-089
2
Pre-Installation Information
IMPORTANT: Read this entire installation manual to ensure proper installation.
IMPORTANT: Flush all the water supply lines before making connections.
Air Metering valve
The air valve pushbutton allows each user to activate an air metering valve (starting the flow of
water) by pushing and releasing the pushbutton. The air metering valve is factory-preset to run for 10
seconds and can be adjusted to run from 5-45 seconds.
Supplies required for installation:
• (4) 1/2" lag bolts, screws or other fasteners to anchor washfountain pedestal
• 1/2" hot and cold water supply lines and fittings (refer to rough-ins on page 6)
• Reducing fittings and 1/2" nom. copper tubing supply lines for types with supplies from
above
• Standard P-trap (refer to rough-ins on pages 5-7)
• 1-1/2" drain lines and fittings (refer to rough-ins on pages 5-7)
• Pipe sealant
Terreon™ Semi-circular Washfountain Warranty
Bradley Corporation warrants to commercial and institutional purchasers only each unit free from defects in material
and workmanship under normal use and service upon the following terms and conditions:
1. This warranty is limited to replacing or repairing, at our option, transportation charges prepaid by the purchaser,
any Bradley unit or part thereof which our inspection shall show to have been defective within the limitations of
this warranty.
2. The period during which Terreon™ semi-circular washfountain components are warranted is as follows:
• Terreon™ bowl warranted for two years
• All other semi-circular washfountain components warranted for one year.
3. This warranty does not cover installation or any other labor charges and does not apply to any units which have
been damaged by accident, abuse, improper installation or improper maintenance.
4. The replacement or repair of defective units as stated in this warranty shall constitute the sole remedy of the pur-
chaser and the sole liability of Bradley Corporation under this warranty. Bradley Corporation shall not otherwise
be liable under any indirect damages caused by defects in the repair or replacement thereof.
5. This warranty extends only to commercial and institutional purchaser and does not extend to any others, including
consumer customers of commercial institutional purchasers.
6. This warranty is in lieu of all other warranties, expressed or implied, including any implied warranty of mer-
chantability or fitness for a particular purpose or otherwise.

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
Installation Instructions TDB3103, WF3203
Bradley Corporation • 215-1479 Rev. A; EN 02-089 3
Semi-Circular Washfountain Dimensions
Air models are ADA Compliant on
Model TDB3103 only
Optional equipment may not comply
with all ADA dimensional guidelines
36" Semi-circular - side view
(Model TDB3103 shown)
Back view
Bottom View
Top view
Figure 1a
*ADJUSTMENTS TO VERTICAL DIMENSIONS
FOR VARIOUS RIM HEIGHTS
Rim Height Application Adjustment
34" Adult Height ADA, TAS Adult Height None, as shown
32" TAS Ages 11 thru 14 or 15, Subtract 2"
Grades 6 thru 8 or 9
30" TAS Ages 4 thru 10 or 11, Subtract 4"
Grades Pre-K thru 5 or 6 &
Proposed Juvenile Height ADA

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
TDB3103, WF3203 Installation Instructions
Bradley Corporation • 215-1479 Rev. A; EN 02-089
4
Semi-Circular Washfountain Dimensions
36" Semi-circular - side view
(Model WF3203 shown)
Back view
Bottom View
Top view
Figure 1b
*ADJUSTMENTS TO VERTICAL DIMENSIONS
FOR VARIOUS RIM HEIGHTS
Rim Height Application Adjustment
34" Adult Height ADA, TAS Adult Height None, as shown
32" TAS Ages 11 thru 14 or 15, Subtract 2"
Grades 6 thru 8 or 9
30" TAS Ages 4 thru 10 or 11, Subtract 4"
Grades Pre-K thru 5 or 6 &
Proposed Juvenile Height ADA

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
Installation Instructions TDB3103, WF3203
Bradley Corporation • 215-1479 Rev. A; EN 02-089 5
Rough-In Specifications continued . . .
Figure 1c
*ADJUSTMENTS TO VERTICAL DIMENSIONS
FOR VARIOUS RIM HEIGHTS
Rim Height Application Adjustment
34" Adult Height ADA, TAS Adult Height None, as shown
32" TAS Ages 11 thru 14 or 15, Grades 6 thru 8 or 9 Subtract 2"
30" TAS Ages 4 thru 10 or 11, Grades Pre-K thru 5 or 6 Subtract 4"
& Proposed Juvenile Height ADA
Rear View

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
TDB3103, WF3203 Installation Instructions
Bradley Corporation • 215-1479 Rev. A; EN 02-089
6
Rough-In Specifications
NOTE: Supply lines for one to two
washfountains should be 1"; for three
washfountains, 1-1/4". For more than
three washfountains, pipe sizes should
be increased proportionately.
Figure 2a
NOTE:
Drain P-Trap &
Supplies
by Others
NOTE: Supply lines for one to two
washfountains should be 1"; for three
washfountains, 1-1/4". For more than
three washfountains, pipe sizes should
be increased proportionately.
*ADJUSTMENTS TO VERTICAL DIMENSIONS
FOR VARIOUS RIM HEIGHTS
Rim Height Application Adjustment
34" Adult Height ADA, None, as shown
TAS Adult Height
32" TAS Ages 11 thru Subtract 2"
14 or 15, Grades 6
thru 8 or 9
30" TAS Ages 4 thru Subtract 4"
10 or 11, Grades
Pre-K thru 5 or 6 &
Proposed Juvenile
Height ADA
Figure 2b

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
Installation Instructions TDB3103, WF3203
Bradley Corporation • 215-1479 Rev. A; EN 02-089 7
Installation Instructions
Step 1: Rough-In Drain & Supplies
1. Rough in supply and drain piping as
required for your installation (see
pages 5-6 for rough-ins of optional
installations).
Step 2: Bowl/pedestal mounting
and assembly
1. Attach the stainless steel pedestal base
to the pedestal using supplied screws
and finishing washers. For wall-
mounted models, see Pages 3-4 for
pedestal height.
2. Position the pedestal at the desired
location and mark the position of the (4) pedestal wall mounting locations.
3. Secure the pedestal to the wall with suitable fasteners, 1/2" anchors and 1/2" bolts (supplied by
installer) (see Figure 1b for wall mounting locations).
4. Using two to three people, carefully lift the bowl onto the pedestal (see Figure 4).
5. Position the bowl so that the threaded rods in the bowl mate with the slotted holes in the
pedestal (see Figure 4).
NOTE: Before attaching 1/4" wing nuts and washers to threaded rods, remove red protective caps
from threaded rods. Discard sleeve caps after removal.
6. Using 1/4" wing nuts and washers, secure the bowl to the pedestal, three places (see Figure 4).
CAUTION: BOWL SURFACE IS SMOOTH. APPROXIMATE WEIGHT OF BOWL IS 75
POUNDS. HANDLE WITH CARE!
Figure 3
4-3/4" (121)
Types A and O
Figure 4

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
TDB3103, WF3203 Installation Instructions
Bradley Corporation • 215-1479 Rev. A; EN 02-089
8
Installation Instructions continued . . .
Step 3: Installing drain spud in bowl
NOTE: Seal between drain spud and drain hole with plumber’s putty (supplied by installer).
1. Secure drain spud with lock nut and washers as shown in Figure 5.
Figure 5
Step 4: Supply Stop Valve,Tubing Connection, and P-trap Installation
NOTE: Flush supply lines before making connections.
1. Using pipe thread sealant, thread supplied 1/2" street elbows into the 1/2" angle supply stops
(see Figure 8, page 11).
2. Again using pipe thread sealant, thread supply stops onto stub-outs.
3. Follow the procedures below and refer to Figure 6 when installing 3/8" tubing into sprayhead to
ensure that you achieve a leakproof seal.
• Using a sharp knife, cut tubing squarely and remove any burrs. DO NOT pinch or crush end
of tubing.
• Loosen nut on fitting. Moisten end of tube and push into fitting until it is firmly seated.
Tighten nut to secure tube to fitting (make sure nut is securely tightened).
• If connector leaks, reseat tubing according to above procedure. If leaking persists,
replace male connector, or call your Bradley representative for assistance.
4. Connect P-Trap (supplied by installer) to tailpiece and drain outlet.
NOTE: Flush supply lines before making connections.
NUT TUBING
MALE
3/8" TUBE
CONNECTOR
145-105
SPRAYHEAD
Figure 6
TUBING

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
Installation Instructions TDB3103, WF3203
Bradley Corporation • 215-1479 Rev. A; EN 02-089 9
Installation Instructions continued . . .
Step 5: Cylindrical Air Valve assembly for A drain and O drain units
1. Install hemmed end (not sharp end) of support tube with gasket onto bowl.
2. Place sprayhead with 3/8" tubing onto support tube as shown in Figure 7 on page 10. Run tubing
down through support tube. Make sure spray holes point away from the wall.
3. Place upper tie bar (notched at corners of both ends) on top of sprayhead parallel to wall.
Connect the two threaded tie rods together using the coupling nut with hex head set screws. Run
the tie rod down through upper tie bar (see Figure 7) and secure from underneath the bowl using
the lower tie bar (no notches) and hex nut with socket head set screw. A minimum of 1-1/2" of
threaded tie rod should protrude below the lower tie bar, this will be required to attach the valving.
4. Place actuator module assembly on top of sprayhead. Rotate until actuator locks in with tie bar.
Drop the 1/8" diameter supply tube down to pedestal.
NOTE: Skip to Step 5 for units without soap.
• For units with soap option, install the spacer, soap dispenser and cover using the coupling nut,
third tie rod (8-5/8" long) and second coupling nut as shown (see Figure 9 on page 12).
5. Secure actuator module cover and top cover with acorn nut and socket head set screw.
6. Holding the valve assembly outside of the pedestal, connect 3/8" supply tubing and the 1/8" air tub-
ing from the sprayhead to valve assembly tube connectors (see Figure 8 on page 11).
7. Thread one supplied 3/8" nut onto the tie rod. Slide valve assembly on next and secure with
another 3/8" nut.
FOR “A” UNIT: Connect flexible hoses to supply stops using suitable fittings.
FOR “O” UNIT: Install 1/2" nom. copper tubing supply lines (pass through holes in cover,
down through support column) and connect flexible hoses to supply stop valves using suitable
fittings.
8. Turn on the supplies and check piping installation for leaks.
9. Clean sprayhead if necessary. See page 17 for sprayhead troubleshooting. Adjust volume
control valve, if necessary, to control the flow of water.

Terreon® Deep Bowl 36" Semi-Circular Washfountain with Air Metering Valve
TDB3103, WF3203 Installation Instructions
Bradley Corporation • 215-1479 Rev. A; EN 02-089
10
PEDESTAL ASSY.
S17-287
DRAIN
269-1597
TIE BAR
MODULE COVER
S04-083
TIE ROD
176-008
SUPPORT TUBE
S57-006
SUPPORT TUBE
GASKET
125-011
TIE ROD PRE-PACK
S45-1336 TOP COVER
107-099 (A)
107-179 (O)
ACTUATOR MODULE
ASSEMBLY
S65-134
TERREON™ SEMI-CIRCULAR DEEP BOWL
(ADA bowl shown, classic bowl is optional)
Part no. varies with color of bowl. Contact your
local Bradley Representative for assistance.
VALVE ASSY.
SEE FIGURE 8 FOR PART NUMBER
SPRAYHEAD
S05-054A
A/O UNITS
(A shown)
Figure 7
3/8" FLEXIBLE
SUPPLY TUBE
R68-600014
COVER
TIE ROD
PRE-PACK
TIE
ROD
COUPLING NUT
AND SET SCREW
SECTION VIEW OF
A/O UNIT ASSEMBLY
SPRAYHEAD
INFRARED
MODULE ASSY.
TIE
BAR
SUPPLY TUBE
ACCESS PANEL
186-1260
Installation Instructions continued . . .